I have a one 3750x switch and 10 nos of 2950 switch, i want to configuration etherchanel between 3750 to 2950, for that i need 10 nos of etherchanel interface(virtual), but the 2950 switch support maximum of 6 nos of etherchanel port?
View 9 RepliesI have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies View RelatedAny experience with bundling a 10GB interface on a 3750G-16TD-S with a WS-C3750X-48T-S with a 10GB interface. I have worked with 5 different TAC engineers and so far I have not gotten an answer on why the switch will not let me bundle the 10GB with another 10GB interface.
Same switch Stack – not a cross stack.
Tried every configuration possible with no luck. I originally thought it might be the stack-ring speed – I corrected that today and it is running at 32GB –
The only thing I can think of now is it might be a hardware limitation on the 3750G-16TD-S ?
Q. What performance of the 10 Gigabit Ethernet port on the Cisco Catalyst WS-C3750G-16TD switches?
A. The Ten Gigabit Ethernet uplink on the Cisco Catalyst WS-C3750G-16TD switches is 1.25:1 oversubscribed and provides maximum throughput of 8Gb/s. –
I am installing a several new Cisco VM servers. The VM hosts are losing connectivity when we apply the etherchannel config in the core stack. VMware has stated that the etherchannel load balance needs to be src-dst-ip in order for the etherchannel to work.However, my current stack has 2 etherchannels configured to other switches through out the bldg in network closets. The current load balance configuration is src-mac.My question....when I make the change to src-dst-ip, will my network connectivity go down? I saw there was an older article on this that doesnt provide an answer just a work around. Here is the article. [URL].
View 1 Replies View RelatedWhen I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
I am trying to configure etherchannel on 2 2960S connected by a flexstack with 2 ports g1/0/52 and g2/0/52 on each 2960.
these switch are connected to a CAT4500, I know that I can only use LACP because of cross-stack but when I force the switch to use LACP witch channel-group 2 Mode active the switch do this :
%With PAgP enabled, all ports in the Channel should belong to the same switchCommand rejected (Port-channel2, Gi1/0/52): Invalid etherchnl mode
% Range command terminated because it failed on GigabitEthernet1/0/52
I don't know how to bundle the 2 ports on the 2960 stack. each time I use : channel-group 2 mode on there is no error
but the switch do this :
*Mar 1 00:45:32.290: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2 and will be suspended (trunk mode of Gi2/0/52 is dynamic, Po2 is trunk)
*Mar 1 00:45:32.531: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2
[Code].....
I have a Cisco catalyst 2950 and would like it's basic setup. It is connected to a Cisco ASA5510 on GigabitEthernet0/1. The ASA has two v lans configured. 101 and 102. I would like to configure my switch to be managed on the following IP which is on the 102 sub net:
172.16.102.253/24
Also, i would like to configure GigabitEthernet0/1 as a runk port to allow both v lans.
Configuring a network with Rapid Spanning Tree Protocol. There's a combination of Cisco 3650s, 2950 and 2960 switches. It is a flat Layer 2 network with a single VLAN. CLI configuration?
View 3 Replies View RelatedI am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies View RelatedService Provider will config a Q-n-Q connection between (2) datacenters. I would like the traffic encrypted over that connection.
Could I use a 3750X at each location and configure Macsec?
I went to configure RADIUS on my 3750X with IOS 15, and lo and behold it is not where it used to be. Did it get moved somewhere else that I can't seem to find very easily?
View 2 Replies View RelatedPossible to configure multichassis port-channel between a VSS and 3750X (Port-channel not in the same switch on the 3750X stack). I got it using LACP but I need Pagp to get VSL redundancy “dual-active detection pagp trust channel-group 1”. I am using the last VSS IOS version 15.0(1)SY. I can’t get the option “switch 1 preempt”, has it changed with other option?
View 2 Replies View RelatedI have two stacks 3750X on two different sites with two links L_2_L, and I want to configure the port channel to aggregate the two links.
Site A Site B
3750X -A1 --------------------------------------( )--------------------------------------- 3750X -B1
( L-2-L )
3750X -A2 --------------------------------------( )--------------------------------------- 3750X -B2
Below the configuration that I have put the two stacks.
site A
interface Port-channel5
description Etherchannel group entre le stack 3750X-A et Switch Lan_2_Lan
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 11,12,999
switchport mode trunk
switchport nonegotiate
speed 100
But the problem is only one link is Bundeled in channel group, see below
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
5 Po5(SU) LACP Gi1/0/15(I) Gi2/0/15(P)
I have a etherchannel defined between 2 L2 switches using LACP as shown below. The etherchannel works fine, however when I hard code speed/duplex on both ends the etherchannel fails. What is causing this behaviour?
SW02:
interface Port-channel5
interface GigabitEthernet1/0/1
switchport mode trunk
[Code]....
how to use Subinterfaces on an Etherchannel for a Lan Failover link?I successfully bundled e0/0-1 and e0/2-3 to 2 Port-Channels with a 3750X Stack - and was able to set my "nameifs" and "security level" on Port-Channel Subinterfaces like "Port-channel1.4" As a lan based failover link the subinterfaces seem to be unusable ....
View 1 Replies View RelatedI am trying to implement an etherchannel on a cisco 2901 (IOS 15.1). i have already created the port-channel but i cannot assign the gig interface to the channel group.
View 1 Replies View RelatedI have two switches 6509 one switch is confire with VTP domain ABC Other switch is configure with ABZ, At present the switch is configure with the L3 interface and one fiber cable is connected between two switches.I want to remove L3 configuration wants to make L2 etherchannel and wants to ceraeate Loop back will assing same ip both side.The OSPF is configure both side , i will not do any changes in the OSPF as L3 ip is advertise in OSPF.
View 1 Replies View RelatedIf the ports on a 5508 can only perform etherchannel(no LACP or PAGP), only on mode, how does a 5508 create a bundle with a nortel switch?
View 1 Replies View RelatedI am about to configure 4 Gig ports for EtherChannel. I've been reading about EtherChannel and it seems easy enough to configure. I have a host (server)which I am going to connect to these 4 - gig ports. This is new for me and would like some feedback for those that have used EtherChannel on their layer 2 switches. The gig ports will be an access port with VLAN XX.
View 6 Replies View RelatedIs it possible to have ether-channel across 2 switches? As an example, having a server with 2 ports connect, 1 port to Switch-A and the other to Switch-B and then use those two links on the sepatate switches but to the same server to form an Etherchannel.
The Switch-A and Switch-B are 3560 series
We have two 6k5 configured as vss and it is working fine. For each floor we have a 3750 stack. In each 3750 stack we have 4 switches. From the first 3750 we have a fiber link to the first 6k5 and from the fourth switch we have another fiber link to the other 6k5 switch, for each floor/3750 stack, both configured as etherchannel. We installled each 3750 stack/floor in different maintenance windows; in all these installations we have problems configuring the etherchannel. After we configure the etherchannel on 3750 stack and in the vss, the etherchannel does not go up/up. We see the etherchannel up/down; after a lot off work, try and error, configuring shut/ no shut, adding and excluding links from the etherchannel; in any aleatory moment the etherchannel goes up/up and works fine. Is there any bug related with these IOS versions, or is there any right procedure to configure etherchannel from vss to 3750 stack?
3750 stack config (IOS
Cisco IOS Software, C3750 Software (C3750-IPBASEK9-M), Version 12.2(50)SE1, RELEASE SOFTWARE (fc2))
interface GigabitEthernet1/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface GigabitEthernet4/0/1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunkchannel-group 1 mode on!interface Port-channel1switchport trunk encapsulation dot1qswitchport trunk allowed vlan 100,101,371,372switchport mode trunk
[code]....
I am trying to review the port-channel configuration on a 6500 series. I am issuing the "show etherchannel summary" command and the out put shows the Group, Port-Channel, and Ports. It does not show me the protocol that is in use such as PAgP or LACP. Does this have to do with the Etherchannel in the "On" mode rather than "active", or "Auto"?
View 2 Replies View RelatedWe have a problem with the throughput over etherchannel in LACP with 2 or 4 ports. It is iSCSI traffic (vmware esxi 4.1 U3) is going from 2 separate NICs (ports) to the etherchannel (with 2 or 4 ports) that has a SAN connected (Nexenta).
The SAN is configured in passive LACP and the switch is in active LACP. Actually it does not matter if we do LACP or just MODE ON, still same result: ~1GBit/s throughtput in either direction. Like already mentioned, 2 or 4 ports in the etherchannel make no difference, or the configuration of the etherchannel.
I will post some config data below, but here is the question: Why can't we see traffic beyond 1GBit/s? Source and destination are capable of doing much more than that (vmware esxi RAID 5 of 1TB SATA; SAN 16 x 1TB NL-SAS). If we look with CNA, we can see that the traffic is balanced equally over the etherchannel ports. With or without QOS or flowcontrol, no difference. This whole traffic happenes on this switch.
!
port-channel load-balance src-dst-ip
!
interface Port-channel5
[Code]....
When you aggregate multiple fiber GBICs together on the 3508G, do you configure it as an etherchannel, or as fibre-channel? I've looked around online for hours, but can't find it mentioned anywhere.
View 3 Replies View RelatedI have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies View RelatedIs it possible to to build a Layer 3 ether channel from two separate physical switches (layer3) that are trunked together?I know you can easily do this on a single switch and on stacked switches which I've done but in this case the customer have purchased two 3560X's which are not stackable yet want redundancy. The purpose of the etherchannel is to connect both switches to a private circuit provided by the hosted partner then route to the same setup in the DR location to different subnets.
View 4 Replies View Relatedseeking for configuration assitance on etherchannel between catalyst 3750 and 6506
View 3 Replies View RelatedI was configuring link aggregation between a Cisco3750 and Cisco SG200 and the switched network went down just a few minutes after the port channel came on.I rebooted the SG200 and all hosts came back up for a minute before I lost them again. The etherchannel was between two trunking ports. I never set link aggregation on the SG200, could that be the reason? All machines are connected to the SG200. The 3750 is only being used as a layer 3 device for inter vlan traffic.
View 1 Replies View RelatedMaybe this was listed in the release notes for the product and I missed it, but can this item support Etherchannel in a 2801 router? I installed the module into the router and the router recognizes the module. I can configure the ports as access or trunk ports, but I am unable to configure the channel-protocol or the channel-group for the Etherchannel. The IOS on the router is 15.1 M with the upgraded Bootloader version 12.3.
View 1 Replies View RelatedWe have a new building where we added 3 network closets with 3750x stacks.We have 2 fiber gig ports connected to 2 microwave units and etherchanneled the to ports
We have the same setup at the corporate office except the connection is 2 fiber gig ports on a 6509. The 6509 is doing the routing
Now the problem is that we lost the connection to the management interface on only one of the three closets after a few days running. But some workstations at the corp office could reach it... others could not. The workstation were on the same VLAN. We solved the problem for a few days by shutting on of the fiber ports on the etherchannel. But is started happening again... now with PCs being installed at the new location.
The PC that was not working on the 3750x side could ping across to the 6509 but no further then that. It seems like an arp issue not routing because some devices are reachable and fully operational throughout the network.
Here is the configuration:
3750x:Cisco IOS Software, Version 12.2(55)SE1
Current configuration : 118 bytes!interface Port-channel1switchport trunk encapsulation dot1qswitchport mode trunkno snmp trap link-statusend
!interface GigabitEthernet1/1/1description 2gig to STB-6509switchport trunk
[Code]......
I been practicing with the configuration of layer 3 etherchannel configuration and i am facing a problem here. I have two 3560 switches and i want a layr 3 ether channel configuration setup between the first 2 ports of bothe the switches. I assign IPs to the Port-channel 1 of both the switches "10.1.1.1 /24 and 10.1.1.2 /24" but i am unable to get a successful ping. what am i doing wrong. below are the configs for bothe of my switches.
3560_1
Building configuration...
Current configuration : 1274 bytes
!
version 12.2
no service timestamps log datetime msec
no service timestamps debug datetime msec
[code].....
I would just like to confirm if it is possible to create a 2x10G etherchannel on a 4948.
View 4 Replies View Related