I get a unclear log entry in a VSS system.
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
Me_Kr #1 ME_KR_ERROR_CNT_LTL_PARITY_ERR_ITRP_0_0[01C8] : INTR= 0001 MASK= 0001
[code]....
I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
An error appear in console (many times in one minute):
Jan 3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
What is the problem? What is the solution?
I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
I'm getting constant %C4K_S2W-4-WRITECALENDARERR: Calendar write operation Failed errors on the console. I was also getting them on the original IOS version.
Anything I've seen say's to ignore them but their very frequent filling up the logs.
There's very little return on google and no bugs to report on Cisco?
I have in logs following error message:
%DEVICE_TEST-2-PWR_MGMT_BUS_FAIL: Module 1
Has failed test SpineControlBus 20 times on device Power Mgmt Bus on slot 10 due to error Spine control test failed error number 0x00000002.
Have a small stack of two 3750 routers. Get the following error message every few secounds:
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
%STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP
Now I replaced the stacking cables but no joy. It was ok for an hr or so but then the error messages popped up again. Also random links on this stack back to access layer user switches have been going up and down randomly. So I have decided to take the next step and upgrade the IOS.
Although when I try and copy a new IOS I get the following error:
%Error writing flash:/c3750-ipservicesk9-mz.122-55.SE6.bin (No space left on device)
Seems this image is 130MB while the image that is currently on it is 74MB and free space is 54MB. How do I get the image onto the router? If I delete the current image from flash will that cause the router to stop functioning?
Also I noticed there seems to be more than one flash directory. See below:
copy tftp: ?
flash1: Copy to flash1: file system
flash2: Copy to flash2: file system
flash: Copy to flash: file system
null: Copy to null: file system
nvram: Copy to nvram: file system
running-config Update (merge with) current system configuration
startup-config Copy to startup configuration
system: Copy to system: file system
vb: Copy to vb: file system
The current router image seems to be in flash1 and flash 2 also. Could I delete the image from flash1. Upload it there and then boot the router from flash1?
my MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies View RelatedWe are running a small network business and as funs of ciscos we own a some of the 4948s.We are facing an issue with couple of them as we get the below error message
C4K_CHASSIS-3-INSUFFICIENTPOWERSUPPLIESDETECTED:Insufficient power
supplies present for specified configuration
First thought to replace the power supply didn't actually work as we did that with no result.Power consumption is not an issue as well because all other 4948s work fine with 1 power supply (forgot to mention is 1 power supply in all of them).
I recently upgraded my network to have two 3750x core, one interface on the Cisco is connecting to a Net gear switch via a fiber converter. I am keep getting the vlan flapping error message in my log as below.
003396: Sep 17 01:46:16.328: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003397: Sep 17 01:46:19.843: %SW_MATM-4-MACFLAP_NOTIF: Host 5c0e.8ba7.0a5c in vlan 2 is flapping between port Gi2/0/15 and port Gi2/0/13
003400: Sep 17 01:49:58.769: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/17, changed state to down
[Code] .....
After my research i think this is a looping issue but I'm unsure how to address it.
I have a Cisco 2800 series and it doesn't boot, only shows this message in the CLI>
Bad RAM at location 0xA0000304: wrote 0xA0000304, read 0xA0000004
What means this? I have to change the RAM?
I am receiving the following error message on a Cisco 3750 switch stack. Need troubleshooting this error message.
00:03:13: %SW_MATM-4-MACFLAP_NOTIF: Host 00d0.7400.2730 in vlan 600 is flapping between port Gi2/0/3 and port Gi2/0/2
I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
I have Nexus 7K installations in 2 locations. Both of them have multiple VDCs. In default VDC there are continous tacacs error message though tacacs is not configured. The requests are from various public IPs where thsi VDC is not exposed to Internet at all. What would be t he cause of it?
%AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user root from 195.2.219.2
2012 Dec 11 16:25:28 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25797]
2012 Dec 11 16:25:34 IDC-FBDTB-AMR2-CN7K-01 %AUTHPRIV-3-SYSTEM_MSG: pam_aaa:Authentication failed for user nagios from 67.78.206.226
- sshd[25799]
[code]....
NEXUS 7000 Octopus internal error in device 78 message. I got this on NEXUS 7000 logs:
Nov 12 22:05:14 smale-outside : 2012 Nov 12 21:05:14 BRST: %MODULE-2-MOD_DIAG_FAIL: Module 2 (serial: JAF1548AMKB) reported failure on ports 2/1-2/32 (Ethernet) due to Octopus internal error in device 78 (device error 0xc4e0025b)
Nov 12 22:05:17 smale-outside : 2012 Nov 12 21:05:17 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
Nov 12 22:05:18 smale-outside : 2012 Nov 12 21:05:18 BRST: %MODULE-2-MOD_FAIL: Initialization of module 2 (serial: JAF1548AMKB) failed
[code]....
I only have found:
[URL]
which does not match reality : No one was configuring Vlans.
When i connect the Router 2821 through the Consol get error message at regular interval of time %ENVMON-4-FAN_LOW_RPM: Fan 1 service recommended.
View 2 Replies View Relatedhow to clear vty line? Please see below. A sh tcp <line number> shows that the TCB is waiting for TCP Process. The TCP processs TCB is waiting for is SSH. I believe because of this ssh process still running, the vty line cannot be cleared.
sh users
Line User Host(s) Idle Location
1 vty 0 pf 10.10.20.8 9w1d 10.10.1.54
2 vty 1 pf 10.10.1.16 35w0d 10.10.1.54
3 vty 2 pf 10.10.1.16 1y14w 10.10.1.54
[code].....
What this crash means? This is a 6509 with a single Sup720 Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI, RELEASE SOFTWARE (fc2)System returned to ROM by s/w reset at 04:42:07 PST8PDT Mon Jan 2 2012 (SP by bus error at PC 0x40C6681C, address 0x424B).
View 1 Replies View RelatedI am planning to upgrade my cat6500 using ISSU but can not find my doc to follow yet.
View 1 Replies View RelatedUsing the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
I wonder whethere it is possible to check the the IOS version on the standby sup720 of a 6500? if yes, what command would you use?
View 5 Replies View Relatedi will be creating combination of SPAN and RSPAN on catalyst 6506 according to the link
[URL]
im planning to implement this on two 6506 switches will this work? or do i violate the number of monitor session? sorce span?
sw1
monitor session 1 source interface Fa5/18monitor session 1 destination interface Fa5/48
monitor session 2 source interface Fa6/34monitor session 2 destination interface
[Code].....
I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
View 0 Replies View RelatedI recently rebuilt the configuration of our Cat6500 multilayer device for use as a user stack. The device is funtioning as it should be, but I am unable to set SSH using the 'crypto key generate rsa' command. The crytop command isn't avaiable at all, which suggests a firmware issue.
I have configured a hostname and Ip domain-name and the image is the only one available.
The show version output is listed below.
show verCisco Internetwork Operating System SoftwareIOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-VM), Version 12.2(18)SXF12, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2007
[Code].....
i have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more 300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.
View 1 Replies View RelatedIf I monitor a trunkport on the rootbridge in both directions I get Duplicate Multicast Packets on the perticular VLAN. The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.
View 2 Replies View RelatedThe router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
I’m deploying new images on my switch 2960 24TT L. After installing the new image (c2960-lanbasek9-mz.122-58.SE1.bin) and reboot the switch I have always this error message : “Error loading "c2960-lanbasek9-mz.122-58.SE1.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c2960-lanbasek9-mz.122-58.SE1.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ ”
But the switch still boot well. Why do I have this error message?
LMS installed on Windows 2003. Backup fais with message "Backup failed.ERROR(1297): Fatal error: Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mode.."
dbbackup.log attached.
i am attaching the image which i recieved last night when i was assigning the IP but i got the error message which does not resembel to IP conflict error messsage
View 1 Replies View Relatedtying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies View RelatedAs soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message. I’ve google’d and turned up nothing so far. I assume I need to allocate more memory to this process.
%PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 312% exceeds warning level 310%
Here's a sh mem:
#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 3008A008 1758530508 647878488 1110652020 1110104020 1109994164lsmpi_io 98FEB1D0 6295088 6294120 968 968 968
We recently upgraded our any connect client from -2.5.3055 to -3.0.07059. This is running on a ASA HA pair running 8.4(2)8. Since the upgrade our users are seeing continual disconnects.
View 2 Replies View RelatedWe have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.