Cisco Switching/Routing :: Cat6500 SUP-2T Service Module
Apr 12, 2012
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status Service Module is Cisco wlan-ap0 Service Module supports session via TTY line 67 Service Module is failed Service Module reset on error is disabled Service Module heartbeat-reset is enabled Service Module is in fail open Service Module status is not available
I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
I am trying to figure out if the new code for ASA SM 9.0(x) or 9.1 is compatible with CAT6500 but I could not find any document that explicity confirms the the INCOMPATIBILITY. This table from the Release notes is not quite clear.
[URL]
It says that code 8.5 is compatible with Cat6500 and version 9.X is compatible with R7600.So are the two different trains now, one for Cat6500 and one for R7600?
My real goal is to find the correct software versions (not interim) that provides compatilibity with Catalyst 6500 with Supervisor 2T and ASASM.
how to clear vty line? Please see below. A sh tcp <line number> shows that the TCB is waiting for TCP Process. The TCP processs TCB is waiting for is SSH. I believe because of this ssh process still running, the vty line cannot be cleared.
sh users Line User Host(s) Idle Location 1 vty 0 pf 10.10.20.8 9w1d 10.10.1.54 2 vty 1 pf 10.10.1.16 35w0d 10.10.1.54 3 vty 2 pf 10.10.1.16 1y14w 10.10.1.54
What this crash means? This is a 6509 with a single Sup720 Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI, RELEASE SOFTWARE (fc2)System returned to ROM by s/w reset at 04:42:07 PST8PDT Mon Jan 2 2012 (SP by bus error at PC 0x40C6681C, address 0x424B).
We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
I recently rebuilt the configuration of our Cat6500 multilayer device for use as a user stack. The device is funtioning as it should be, but I am unable to set SSH using the 'crypto key generate rsa' command. The crytop command isn't avaiable at all, which suggests a firmware issue.
I have configured a hostname and Ip domain-name and the image is the only one available.
The show version output is listed below. show verCisco Internetwork Operating System SoftwareIOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-VM), Version 12.2(18)SXF12, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2007
i have a campus network with 2 core Cat6500 and multiple 4500 series distribution switches plus 2960 series access switches,we have deployed IPTV system in the network but currently 50 TVs are working through sattelite stream from streaming server Cisco's DCM 9900.we are planning to add more 300 TVs in the network and i am wondering that when all of them will be deployed then what will happen for switches cpu utilizations when all the Tvs will be running on the same time with different different channels.
If I monitor a trunkport on the rootbridge in both directions I get Duplicate Multicast Packets on the perticular VLAN. The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
When you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
