I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies
on IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)I can see errors in the TCAM if I issue the command
View 21 Replies View RelatedI am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies View Relatedcan I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedI have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies View RelatedIs there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies View RelatedI just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies View Relatedi am currently trying to configure a four port ISDN BRI interface on a Cisco 2811 router.Upon upgrading to a later version of IOS, c2800nm-advipservicesk9-mz.124-25d.bin, access to the HWIC-4B-S/T module is lost, the router no longer detects it. In fact iI can only get the router to detect the module using the original IOS version c2800nm-advipservicesk9-mz.124-20.YA3.bin.
Is there some special feature needed in the IOS code to support these modules, if so what would be a suitable version/train to upgrade to?I have tried using the Cisco Software advisor tool but it generates an error when searching on a hardware configuration containing this module type.
The reason for upgrading the code is we have a potential bug with the current version which appears to be preventing the BRI interface syncing up with the providers switch (switch type correctly defined and provider confirms isdn line has been provisioned correctly).
The debug error seen is:
GMT: ISDN BR0/0/0 SERROR: L2_Go: at bailout DLCB is NULL
L2: sapi 63 tei 127 ces 0 ev 0x650
My main question though is why the module is not being detected after a code upgrade and if there is a specific code version/train needed to support this module in a 2811?
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies View RelatedDoes ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies View RelatedMy ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View RelatedI m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedI have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
On 2921, how do you quite service-module session and get back to the router?
View 3 Replies View Related[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
i have question about router 2811, for now, all HWIC in 2811 is full,
Slot 0 : VIC2-2E/M
Slot 1 : VIC2-2E/M
Slot 2 : WIC-1T=
Slot 3 : HWIC-1FE
But we need add more 2 module VIC3-2E/M. can we use Network Module ? example : add one NM-HD-2V + two VIC3-2E/M ?
Can we do that? and whether it is the same as we use the VIC2-2E / M on HWIC slots
I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies View Relatedhow we can select a network module for 2811 router?gigabit or ethernet Hwic?
View 1 Replies View RelatedI have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
I have an issue where I am trying to start my VPN and continually get the following message: Error 56: The Cisco Systems, Inc. VPN Service has not been started. Please start this service and try again.
So I have been into Services to 'start' Cisco Systems, Inc. VPN Services - this then always comes up with this error: Error 1053: The service did not respond to the start or control request in a timely fashion
The solution mentioned on other posts on disabling the ICS but it was already disabled. When I try to start VPNGUI I also get error 56 and when I try to use services.msc to start the service I get error 1053. Then also when I try to start from task manager services(cvpnnd) i get access denied.
I have done new configuration for CPI 1.2. while i tried to start service i got belw error. [code]
View 3 Replies View RelatedI have a 2811 with 512 of memory installed (two by 256). The router has been sitting spare for sometime and I know there was once a memory problem with it long ago. It has two 256M Non ECC DIMMs installed and seems to work fine. I recently tried to install a 512M DIMM ECC and all I get is 'Unsupported DIMM" error - same if I remove the other 256M DIMM leaving just the 512M. I have tried three different DIMMs - and all have the same error message. One of the DIMMs is 'cisco supported' and based on what I can find in the web - seems to be the correct spec. I have also tried non ECC 512 DIMM and 'unsupported DIMM" error message is still coming up. If I did not know better, I would say that there was something that needed changing in the config to allow 512M DIMMs to be installed.
View 6 Replies View RelatedDHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies View RelatedI had a virus. I think I got rid of it. Avast scans and boot time scans and Super Anti Spyware and TDSS killer report all clear. However, the network shield of Avast and the Internet don't work. Points to note: 1. In services, the DHCP and DNS cannot be started. I get the error 1075: service has been marked for deletion or one of it's dependancies are missing. (close to that)
I've checked the dependancies of both, and reinstated the ADF module in device manager after selecting the 'View Hidden' option.
We have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active) SerialNo : SAL1521E035
Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port 1 2 3 4 5
-------------------
U U U . F
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.
Have spa module on 6509E experience that error:
!
sh log | b crash
SLOT 3: Aug 18 12:52:10 CST: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on
Ingress ESF Engine: Control Store Parity Error
SLOT 3: Aug 18 12:52:10 CST: %ESF_CRASHINFO-2-WRITING_CRASHINFO: Writing crashin
fo to disk0:crashinfo.esf_20110818-175210
[Code]....
I have a 2811 Router that keeps cycling through reboots. About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below. It then does a dump and reboots. This cycle just continually occurs.
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)
I an currently running Cisco (ACS 5.2.0.26.3) and attempting to get my Cisco 5508 WLC's (7.0.98.0) loaded into ACS for TACACS+ authentication for managment users.
However I keep getting the following error:
*emWeb: Sep 14 14:44:45.931: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed for the user:test_tac. Service-Type is not present or it doesn't allow READ/WRITE permission.
Now I've attempted the step-by-step using the following URL but to no avail.( there are some slight differences in ACS 5.2)
[URL]
Latest WLC configuration guide I could find (Software Release 7.0 June 2010) isn't much useful either.
I had a problem during setup of a new module N7K-M148GS-11 into a Nexus 7000 10-Slot chassis.The module was powered-dn and removed by platform with the following message: [code]
Do I need to upgrade nx-os? There is a workaround?
