Cisco :: Wrong IOS On A Switch Service Module?
Mar 11, 2013
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies
ADVERTISEMENT
Feb 25, 2012
My folks have Time Warner (Roadrunner) Internet service. They power-down their Dell every night. When they shut down last night they had no problems and were running Time Warner (Roadrunner). When they booted the computer this morning the computer is trying to connect to Adelphia.
They changed nothing. The wiring to the computer was not compromised in any way.
Time Warner tried to "ping" their modem and could not "see" the modem. They think it is a line problem - but the fact that the computer is looking to connect to an alternate service provider makes me think that it is possibly a problem with a setting in the computer.
View 1 Replies
View Related
Jan 1, 2013
can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies
View Related
Dec 5, 2011
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies
View Related
Jun 3, 2013
Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies
View Related
Mar 20, 2013
I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
View 2 Replies
View Related
Apr 12, 2012
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
View 2 Replies
View Related
Mar 10, 2013
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies
View Related
Mar 27, 2012
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies
View Related
Dec 27, 2011
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies
View Related
Sep 1, 2010
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies
View Related
Dec 2, 2012
My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
View 2 Replies
View Related
Jul 25, 2012
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
View 3 Replies
View Related
Jun 17, 2012
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies
View Related
Jun 8, 2011
I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies
View Related
Dec 12, 2011
I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
View 4 Replies
View Related
Jun 9, 2012
On 2921, how do you quite service-module session and get back to the router?
View 3 Replies
View Related
Oct 18, 2012
[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
View 1 Replies
View Related
Jun 6, 2013
I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies
View Related
Mar 17, 2011
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
View 5 Replies
View Related
Feb 26, 2012
I am trying to get the temperature reading from one of our 3560G Switches using SNMP. When I run an snmpget on the Switch it returns back to me a "1".
So when I run the following I get:
> snmpget -v1 -c public 192.168.x.xxx 1.3.6.1.4.1.9.9.13.1.3.1.3.1005
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1005 = Gauge32: 1
But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
View 4 Replies
View Related
Oct 20, 2012
it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?
View 8 Replies
View Related
May 14, 2011
Windows 7 with wireless adaptor connection
I switched to Win. 7, because XP getting slow in general. I've using the brand new Netgear wireless adaptor on Win.7 while the older wireless adaptor is still on XP, but I never use XP after switch to Win.7.
On XP, Wireless connection had no issue at all, however on Win.7, the wireless connection often saying 'not service available' at the right bottom corner.
On XP, Netgear was 150 and Win 7 is 300.
Just wonder whether I should take off the wireless-adaptor from the XP if that would work to boost the wireless connection on Win.7?
View 1 Replies
View Related
Aug 8, 2012
I have a Ethernet module (SM-ES3G-16-P) installed in a 3945 router and noticed during first boot no licenses are active at all. I would assume at a mimimum ipbase would be active. With this module, does static routing work with just ipbase?
Example:
interface g0/1
no switchport
ip addr 192.168.254.2 255.255.255.0
[code]....
View 3 Replies
View Related
Jun 5, 2012
Does the Network Module "C3KX-NM-1G" and "C3KX-NM-10G" for Cisco Catalyst Switch 3750X Comes with a transciever like GLC-SX-MM or SFP-10G-SR or do I need to order in seperately.
View 1 Replies
View Related
Oct 11, 2011
We have Cisco 3945 Router with SM-ES3-24P Switch Module. when we tried to configure routing in Router and Layer 3 ports on Switch module, the inter-communicaiton is not working?
how we can use routing in 3945 with SM-ES3-24P module?
View 2 Replies
View Related
Jan 5, 2013
I have one 3945 router with SM-ES3-16-P module with SL-ES3-16-IPS. I am not seeing any license for this module in CLI output of my router. How do I add license for this module and activate. do I need IP Service IOS for this module
View 1 Replies
View Related
Mar 19, 2012
can you enable dhcp service on a 3560 switch.
View 3 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Sep 3, 2012
Any doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies
View Related
Apr 28, 2012
We have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies
View Related
Sep 18, 2012
I'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies
View Related
Jan 12, 2013
i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies
View Related