Cisco Switching/Routing :: 35609-X - Wrong Image On Switch
Mar 17, 2011
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
View 5 Replies
ADVERTISEMENT
Oct 20, 2012
it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?
View 8 Replies
View Related
Oct 31, 2012
I wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies
View Related
Dec 2, 2012
We've ordered a 4500 core switch and 4948 Server Farm switch for our client, but the switch box does not include a IOS image CD or anything related to IOS image and now the client is asking us why is this item missing as the IOS
-S45UK9-32-1502SGCAT4500e SUP7e Universal Crypto Image
-S49IPB-12253SGCisco CAT4900 IOS IP BASE W/O CRYPTO
View 4 Replies
View Related
Sep 10, 2012
i am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies
View Related
Jan 8, 2013
I am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
View 14 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Nov 19, 2012
I'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies
View Related
Oct 31, 2011
I've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
View 9 Replies
View Related
Feb 28, 2011
128 compact flash got corrupted and suddenly not working after i reboot the 2801 router. now i have a new 256 compact flash and 512 compact flash but i cannot still to boot the 2801 properly. it always do looping like booting in rommon and will be the image decompress but in the end theres an error, Wrong system software for this hardware. ive tried different ios but still the same.
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 262144 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabled
Readonly ROMMON initializedprogram load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0x2fae3d4Self decompressing the image : ##################################################################################################################################################################################[Code]....
View 1 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Feb 27, 2012
I currently have a wired router (Cisco RV042), a wireless router (Cisco WRT110), and a switch for my network. I have the RV042 on a 192.168.5.1 subnet, and that is where my server and other local resources are. I wanted to add wireless for guests, but do not want the guests to have access to local resources, so I plugged the wireless router into RV042 and configured it for a 192.168.1.1 subnet. I can get internet access, but when I connect with a laptop to the wireless router, I end up being assigned an IP in the 5.1 subnet. I set up the VLAN setting in the RV042 for the correct port, but for some reason I am still being assigned the wrong IP, and I can hit local resources on the wireless.
View 1 Replies
View Related
Oct 26, 2011
I just upgraded my power supply's from 2500Watts to 4000watts, however the show power still shows 2500watts.how do i make the 6513 recongize the change? I do have 250volts at 30 amps connected to each power supply.
system power redundancy mode = redundant
system power total = 2331.00 Watts (55.50 Amps @ 42V)
system power used = 1741.74 Watts (41.47 Amps @ 42V)
system power available = 589.26 Watts (14.03 Amps @ 42V)
[code]...
View 1 Replies
View Related
Dec 29, 2011
Setup is like this: Poly com IP phones -> Cisco 2960 switches -> Cisco 2621XM router running 12.28(r). A Windows 2003 server running on HP Proliant DL380 G4 with the correct DHCP scope is configured for the IP phones, also sitting on a Cisco 2960 switch.
A typical port config on the 2960 is:
interface FastEthernet0/1
switchport mode access
switchport voice vlan 60
mls qos trust cos
auto qos voip trust
spanning-tree portfast
spanning-tree bpduguard enable
Relevant section of the config on the 2621XM router:
interface FastEthernet0/0
no ip address
no ip redirects
no ip proxy-arp
ip pim sparse-dense-mode
[Code] .......
This used to work on a Windows 2000 server which sat on different piece of hardware, but stopped immediately after the migration to Windows 2003 server was done. There was no change on the router or switches prior to or after the server migration. I see DHCP server log on the 2003 server giving DHCP NACK because the phones are apparently asking for IP's in the data VLAN.
View 14 Replies
View Related
Feb 12, 2013
- Incoming frames on three of a blade's four switchports are being put into VLAN 1 even though the ports are either in other access VLANs, or are configured as trunks with different VLAN IDs being tagged by the server. - When the ports go down the access VLAN is removed from the port.
Switch stack: 4x WS-CBS3120X-S, 12.2(58)SE1
HP blade: HP BL460c Gen8
This combination has been used successfully elsewhere.
Switchport configuration:
!
interface GigabitEthernet1/0/13 -------> THIS PORT IS OK
switchport mode trunk
[Code].....
View 1 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Apr 14, 2013
When I config BGP on my 3750X Switch, it show error as below:
protocol not in this image
should I need to upgrade the IOS or Where I can found a supported image (support BGP)
View 1 Replies
View Related
Jan 9, 2013
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies
View Related
Jan 11, 2012
I'm not able to find in all the datasheets what's the default (out-of-the-box) IOS image of a WS-C4900M.When I buy a WS-C4900M I know that there is an IP-BASE IOS but which version?
On the datasheet there is a 12.2SG but is an IPBASE with SSH? W/O SSH? UPGRADE SSH? I'm trying to make a comparison between this image and a cat4500e-entservices-mz.150-2.SG2.bin (Advanced Enterprise Services) on the feature navigator to make sure the our customer need this last IOS Upgrade.
View 7 Replies
View Related
Mar 8, 2013
I have 4948E module switch at customer site and below is the show version output. Image on the switch is not supporting 'AUTO QoS' as i need to enable Auto Qos on it to prioritize Voice traffic. Which image supports Auto QoS feature . Image should have L3 functionality also i mean it should support Routing protocols. I tried to enable auto QoS using by configuring "QoS' globally but no luck...with existing image.
{ URL}
ROM: 12.2(44r)SG9
Hobgoblin Revision 20, Fortooine Revision 1.22
Switch up time is 12 hours, 1 minute
System returned to ROM by reload
[ code]...
Configuration register is 0x2012
Switch#sh boot flash:
-#- --length-- -----date/time------ path
1 25793234 May 31 2011 15:20:20 cat4500e-entservicesk9-mz.122-54.SG.bin
2 25005209 Mar 08 2013 09:53:18 cat4500e-entservices-mz.122-54.SG1.bin
70033408 bytes available (58249216 bytes used)
View 1 Replies
View Related
Feb 29, 2012
i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
Aug 7, 2012
I own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies
View Related
Feb 15, 2012
I have a simple question: In 6500 CatOS, we had that feature of image synchronization, which added the ability to download the image from the active supervisor to the standby via internal TFTP of the CatOS. Can this be done on IOS? I was looking fot this over the Internet and couldn't find anything.
View 1 Replies
View Related
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
May 13, 2013
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies
View Related
Apr 24, 2013
I have L3 switch 3560 v2 cisco switch. If i connect the switch via the console cable in XP system i am not getting any responce. I think i need to install via XY mode.
how can i install the ISO iamge via XY mode in cisco switch 3560 v2.Cisco Model: WS-C3560v2-48tS-S.
View 10 Replies
View Related
Jun 12, 2012
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
View 5 Replies
View Related
Jan 8, 2012
Customer has ordered the following routers, which will go in three separate locations.
1. 3945 W/SPE150, IP Base Image
2. 3945 Voice Bundle, includes PVDM3-64 and (1) 2-port T1 MFT
3. 2911 IP Base Image.
If the customer wants to move the Voice image from the existing 3945 to the 3945/WSPE150, would he just need to contact Cisco Licensing, or would the customer have to pay for a software upgrade on the 3945/WSPE150?
Same scenario, except moving the Voice Image to the 2911 router.
View 5 Replies
View Related
May 18, 2013
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
View 7 Replies
View Related
Apr 25, 2013
find what feature set is supported on this IOS S45EUK9-33-1511SG The client requires Layer 3 functionality so do i need to apply any license with it or it will perform layer 3 routing (like rip, ospf, bgp, ipv6, ospfv3) ?
View 1 Replies
View Related
Jan 20, 2013
What features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies
View Related
Mar 11, 2013
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies
View Related
