Cisco Switching/Routing :: WRT110 - Two Router LAN - Wrong IP?
Feb 27, 2012
I currently have a wired router (Cisco RV042), a wireless router (Cisco WRT110), and a switch for my network. I have the RV042 on a 192.168.5.1 subnet, and that is where my server and other local resources are. I wanted to add wireless for guests, but do not want the guests to have access to local resources, so I plugged the wireless router into RV042 and configured it for a 192.168.1.1 subnet. I can get internet access, but when I connect with a laptop to the wireless router, I end up being assigned an IP in the 5.1 subnet. I set up the VLAN setting in the RV042 for the correct port, but for some reason I am still being assigned the wrong IP, and I can hit local resources on the wireless.
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
I just upgraded my power supply's from 2500Watts to 4000watts, however the show power still shows 2500watts.how do i make the 6513 recongize the change? I do have 250volts at 30 amps connected to each power supply.
system power redundancy mode = redundant system power total = 2331.00 Watts (55.50 Amps @ 42V) system power used = 1741.74 Watts (41.47 Amps @ 42V) system power available = 589.26 Watts (14.03 Amps @ 42V)
Setup is like this: Poly com IP phones -> Cisco 2960 switches -> Cisco 2621XM router running 12.28(r). A Windows 2003 server running on HP Proliant DL380 G4 with the correct DHCP scope is configured for the IP phones, also sitting on a Cisco 2960 switch.
A typical port config on the 2960 is: interface FastEthernet0/1 switchport mode access switchport voice vlan 60 mls qos trust cos auto qos voip trust spanning-tree portfast spanning-tree bpduguard enable
Relevant section of the config on the 2621XM router: interface FastEthernet0/0 no ip address no ip redirects no ip proxy-arp ip pim sparse-dense-mode [Code] .......
This used to work on a Windows 2000 server which sat on different piece of hardware, but stopped immediately after the migration to Windows 2003 server was done. There was no change on the router or switches prior to or after the server migration. I see DHCP server log on the 2003 server giving DHCP NACK because the phones are apparently asking for IP's in the data VLAN.
- Incoming frames on three of a blade's four switchports are being put into VLAN 1 even though the ports are either in other access VLANs, or are configured as trunks with different VLAN IDs being tagged by the server. - When the ports go down the access VLAN is removed from the port.
Switch stack: 4x WS-CBS3120X-S, 12.2(58)SE1 HP blade: HP BL460c Gen8
This combination has been used successfully elsewhere.
Switchport configuration:
! interface GigabitEthernet1/0/13 -------> THIS PORT IS OK switchport mode trunk
it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?
I am trying to allow clients coming in from my "DMZ6" interface with source IPs from the subnet 192.168.2.0 /24 to ping and access hosts on my "DMZ1" interface with destination IPs in the subnet 10.5.11.0 /24. I think I have the associated static NATs and the ACLs set up to allow this to happen. What I have noticed from syslog messages is that the PIX is trying to build the TCP connection to the "Inside" interface, rather than to DMZ1. Even though the destination host (10.5.11.12) is directly connected on DMZ1, the PIX is still trying to send the traffic to the "Inside" instead. I tried adding a host route to force 10.5.11.12 /32 pointing to DMZ1 and the PIX still tries to send the packets Inside. This only seems to happen when I try to go from DMZ6 to DMZ1. If I try to access hosts located in DMZ3 for example, which is also a directly connected interface on the PIX, it appropriately builds the connection to DMZ3. Here are the pertinent rules. Why would the PIX want to build the connection to the Inside, even though it knows that the destination host IP is directly connected to DMZ1?
ip address DMZ1 10.5.11.1 255.255.255.0 ip address DMZ6 10.5.16.1 255.255.255.0 ip address inside 10.5.18.17 255.255.255.240
I tried to find a suitable firmware for it & found this, Wireless Router, but when I upgrade the device with this firmware , every thing go wrong .. no english language cant upgrade anymore I tried to reset the device to its factory defaults by pressing the reset botumn but the nothing changes
We have an ASA5520 running ver 7.0(8), nat-control is disabled. On the "outside" interface we have a closed network which is publicly addressed i.e. no access to Internet. We also have two Vlan interfaces on a trunk connection i.e. "inside" interface (Vlan7) and "dmz" interface (Vlan802). Traffic from the "outside" to "inside" is statically NAT'd such that the public IP is translated to a private IP when accessing the "inside" interface. However, our OSS servers on the "dmz" interface need to be able to receive packets from the public IP addresses on the "outside" . All is okay with the outside to inside traffic and traffic initiated from the OSS servers on the "dmz" to the outside works okay (snmp gets etc) i.e. the servers receive reply packets from the public addresses of the outside devices.
However, traffic that originates on the "outside" interface (snmp traps etc) which is destined for the "dmz" is actually being routed to the "inside" interface and therefore the public source address is being NAT'd by the static NAT command. The access-list "in_on_outside" has relevant entries to allow connectivity from outside to dmz, we have tried a static nat command (outside, dmz) to maintain the public addressing but this made no difference and also a nat exempt. With ########nat-control disabled - do I still need a translation or NAT exempt for the "outside" <> "dmz" traffic flow, if so how should this look ?
I bought this router last year (out of warranty) and it has worked great... until 3 days ago. I came home and noticed my laptop (Dell Inspiron 1525) only had "local access only" in the network center. "Local only" both in a wired and wireless connection. I then unplugged my modem, my router, and restarted my computer. I turned everything back on and still nothing. I also checked for wires and the other simple stuff like that. The internet connection works normally when I plug Ethernet cable directly into my computer and bypass the router .My iPhone will connect to the router as well... just with no internet connection?
The unit seems to be Ok, but it's not. Power light is solid blue, Internet light is flashing blue when connected to cable modem, when wireless is on wireless light flashes blue, when ethernet cable is connected the correct 1-4 blue light flashes.The unit issues IP addresses wirelessly with or without security, and on ethernet, but with no Internet access.I can log on to the router and have upgraded firmware to 1.0.07. Tried reset button a number of times, makes no difference.When logged in to the router and looking at the Status screen, it shows no IP address, no Subnet Mask, no Default Gateway, no DNS, thus I can't get on the Internet. Connection type is Auto Config - DCHP. It does show the correct domain name as other wireless routers show.
Tried everything I could find on the boards (hard reset for 30 seconds, cycling power). The power light's the only one that's coming on and I can't tell if it's on continuously or just blinking really fast.
No problem with direct connection to the modem via ethernet, but I can't see the WRT110 via ethernet or wireless. It just suddenly stopped working yesterday.
When I type the routers IP address in teh brower window, nothing happens so I cannot access the router setup. I have a WRT110. What am I missing. I was able to do that when I first setup the router.
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
I am trying to update my WRT110 which has 1.0.04 firmware on it right now but when i try to update it toVer.1.0.05 all i get is this message.... i dont know what to do i never had a problem updating my older router's befor i had this one this is the first time im updating this one i tryed updating it on IE 8 RC1 & also Safari 4 but i get the same message . I've also tryed saving the firmware file in it's own folder still no luck try updating on my xp desktop & my laptop with vista with same message? is it a problem with linksys with the file on there website maybe?
The WRT110 is hooked up to Cable through Comcast and works fine with LAN connections. The problem comes in with more than one wireless laptop tries to connect. First, it was loaded with 1.0.4 firmware and my girlfriend's XP laptop would connect but drop the connection a lot. My Windows 7 laptop wouldn't connect at all. After trying everything someone recommended upgrading the firmware to 1.0.7. Well, now my Windows 7 laptop connects but the XP laptop will not. The DHCP won't assign it an IP, although it says it's connected.
I see that many people have the same problem, random disconnects. I am a long term sufferer from this. I have called support before they can't fix it. and being knowledgeable with routers has not worked at all. I turned off every wireless device in the house, even the microwave it still happens. I change the channel countless times it still happens.
I have a WRT110 wireless router which disconnects suddenly and continuously. In addition, its performance is really poor. The current firmware installed is 1.0.03. I found a new firmware for this model (1.0.04.10) but when I try to install it, I choose the .bin file downloaded from Linksys TechSupp website, click on the "Start Upgrade" button, but I always get the following message "Please designate the path to the firmware".
I have a WRT110 wireless router. My problem is that my laptop has issues connecting to my router. It sees it and shows that there is a strong signal but sometime it will connect other times not. My laptop has no problem connecting to other wirelss routers. And my other devices have no problem connecting to our router. I've reset the router several times and changed the router to no password or security of any sorts. How can I get my Laptop to connect to my router?? I feel like it is a setting issue between the Router and the laptop. Is there a way I can erase the history of the router from the laptop and start fresh?? Like I've said I have reset the router several times. Does it have to do with my firewall?? It's just frustrating that my laptop can connect to anything but this Router. And my other devices like our blue-ray and Wii can connect to the router without problems so why can't my laptop and router connect to each other?
I have a WRT110 router connected to my desktop computer. The router works great for the desktop and one laptop, but if I try to connect a second laptop it disconnects the first one.
When I type the routers IP address in teh browser window, nothing happens so I cannot access the router setup. I have a WRT110. What am I missing. I was able to do that when I first setup the router.
I have a WRT110 router (firmware v. 1.0.04) and a PC and an XBox 360 connected to it (both via cable). Every 15-20 minutes the connection is dropped for appr. 1-2 minutes. I tried modifying several router settings, but the connections are still being dropped
I have a WRT110 that let's a wired connection through to the internet but none of the wireless connections. I'm connect to a new Motorola DSL modem provided by AT&T. (Lightening killed the last one) My wireless stuff can talk to each other but can't access the internet.
I'm trying to upload some images for my job but everytime I hit the up load link to get the image loader I get a redirect to [URL]
What does this mean? I know its a router thing because I tried getting the image loader by using the computer directly from the modem and I didn't run into the issue. Do I have to open a port or something cause all I know is the router is on security lock down.
i have problem with wi-fi network and WRT 110. Seems to me that router only accepts 1 device. I used to have only 1 device (laptop) using wi-fi and desktop connected with ethernet as a second device. It worked just fine. Recently I added 2 wireless devices : apple tv and ipad 2. I can access wireless network only with one of them being “on” at the time (e.g. apple tv works when ipad and laptop don't use wi-fi. As soon as I connect another device router stops working (i'm loosing connection for wi-fi and ethernet) and I don't have internet access until I reboot router. (it happened only once for short period of time – about 40 min.- that I was able to connect to wi-fi with 2 devices. After that it never happened again). I'm not sure if I need newer router or I can still make it work with wrt 110.
Mac airport shows full bars in network connnection and green connected dot, but no access to internet. Ethernet connection works fine. I also couldnt connect with my Iphone.
I have Charter cable with Motorolla SB6121 modem. I've reset the modem, rebooted everything, cloned my ip address, all several times .......but still no go.
Linksys says they don't support this router anymore accept for a pay for support service, which I would like to avoid.
I have a Linksys wrt110, and we didnt have a password on it for a while, i went and changed it so we had a password,now i have put a password on it, and now it wont let me connect any device to the internet, checked iphone and mac, nothing will work.
My brother has an HP G60 from 2009 with windows 7 home premium and 64 bit operating system. Whenever he turns it on and connects it to the internet, the whole network crashes. My xbox, ipod, laptop, and the main desktop (Which we also just changed to a Dell one.)downstairs all cannot connect to the internet. This lasts from anywhere between 2 and 15 minutes and it continues to crash the internet in about 15 minute intervals as long as his computer is connected to the internet. No other devices in the house cause this as I can have all of my stuff connected and nothing happens. We have a Linksys WRT110 router but I don't think that or the modem is the problem as we have changed both multiple times. This has been happening for about a year ever since my oldest brother gave my brother the laptop.
I have a hardwired HP computer with no problem connecting. The remainder of my wireless devices will not access internet. No problem until about 3 weeks ago then all of a sudden it stopped. All wireless devices detect the router/network, but will not allow access to the internet.
Set up: Router: WRT110 1 computer connected via ethernet cable 1 computer using a wireless nic card from cisco
The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).
The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
I don't understand how to even frame this problem in a concise manner, much less seek information as to how to resolve it. It's seemingly giving all priority to the computer connected via ethernet but I that's just intution speaking.
we upgraded our router from WRT54G V5.0 to WRT110. before we dont have any issues using the ACCESS RESTRICTION from WRT54G but now on WRT110 we encounter a GLOBAL BUG. we are blocking the website like Youtube, Friendster, Facebook etc. on the EDIT LIST TAB we specify 4 IP Address that will not going to access the said websites. The problem is...all Computers (about 15 PC) that are using the Internet cannot access the said website also but we did not enter the other IP's.
A couple days ago I noticed that my wireless internet connection on my iPhone would cut in and out, then stopped all together. I also had no connection on my mac which is wired to the WRT110. I bypassed the WRT110 and then I had a connection on my Mac meaning the WRT110 is the problem. I haven't changed or added anything lately that could've caused this....
