Cisco Switching/Routing :: 2960 / Recovering Switch With Wrong BAUD Rate?
Oct 20, 2012
it seems that i made a mistake when typing the BAUD rate of a 2960-Switch in rommon.I can't start the switch now, because there is no image on it (because I deleted it before) and the baud-rate has wrong settings. When connecting via console cable i can't see anything (except some strange hieroglyphics) when starting. I tried all the speeds in teraterm... without success.what can i do, to recover the switch back?
View 8 Replies
ADVERTISEMENT
Mar 18, 2013
how to change the Baud Rate on Cisco 2900 SW utilizing ROMON ?
View 8 Replies
View Related
Dec 29, 2011
Setup is like this: Poly com IP phones -> Cisco 2960 switches -> Cisco 2621XM router running 12.28(r). A Windows 2003 server running on HP Proliant DL380 G4 with the correct DHCP scope is configured for the IP phones, also sitting on a Cisco 2960 switch.
A typical port config on the 2960 is:
interface FastEthernet0/1
switchport mode access
switchport voice vlan 60
mls qos trust cos
auto qos voip trust
spanning-tree portfast
spanning-tree bpduguard enable
Relevant section of the config on the 2621XM router:
interface FastEthernet0/0
no ip address
no ip redirects
no ip proxy-arp
ip pim sparse-dense-mode
[Code] .......
This used to work on a Windows 2000 server which sat on different piece of hardware, but stopped immediately after the migration to Windows 2003 server was done. There was no change on the router or switches prior to or after the server migration. I see DHCP server log on the 2003 server giving DHCP NACK because the phones are apparently asking for IP's in the data VLAN.
View 14 Replies
View Related
Nov 5, 2009
To rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
View 4 Replies
View Related
Nov 14, 2011
I have a 2960 that I need to limit the uplink port to 50Mbps for 3 vlans and 350Mbps for another vlan. Would the following config achieve that or is this even possible for the 2960?
class-map match-any VLAN50-51-52
match vlan 50-52
class-map match-any VLAN53
[Code].....
View 1 Replies
View Related
Jan 27, 2013
I've configured all my devices in the lab to use 115200 baud rate, so I can speed things up a little at the console. For whatever reason, I can't get my 3550 to save the 115500 baud rate. I power on the switch, hold the mode button, at the switch: prompt I type 'set BAUD 115200' followed by a reset. I power the cycle the switch once more, yet it still holds at 9600. I did the same process on my 3560's and it worked like a charm.
View 3 Replies
View Related
Apr 18, 2010
Having trouble resetting the baud rate to 9600 on a 3750-E. Basically the device cannot be set to anything other than 115200 baud rate. I have changed this via startup-config (which lost connection) reconnected and saved config but after reload was back to 115200. Tried via bootloader to 'set 9600' but the termial program paused for a bit then the switch prompt returned. Tried the same to 'unset baud' but the same thing as above happened. I have erased and reloaded flash etc
View 8 Replies
View Related
Jul 6, 2010
Cannot access console baud rate has been changed by customer and I have tried all the standard ones 1200,2400 ect, have tried the J7 baud jumper on the mother board....?
View 11 Replies
View Related
Aug 8, 2012
I need to use very long console connection it over 56 feet (17m) (I used Cat6 wire with connection on oth ends as console wire 12345678-87654321) According to the below table
Data rate (bps)Distance (m) 2400
60
4800
30
[Code]....
View 1 Replies
View Related
Feb 14, 2013
I have a 2921 router with 1 etherswitch module installed. I haven't done it before and was trying to change the baud rate to 115200 for installing an IOS on the etherswitch module which had been deleted. I ended up "unsetting" the baud rate on the etherswitch and rebooted. Now, when I try to session into the etherswitch, its opens the connection but I can no longer see any text on the screen. Im using Teraterm. I've tried different baud rate settings for my serial port in TeraTerm but still cant see any text on the screen. I dont know of any commands from the router prompt. Any suggestions to fix this? If can start seeing the text, then I can probably configure and set up the etherswitch module.
View 1 Replies
View Related
Mar 17, 2011
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
View 5 Replies
View Related
Oct 30, 2011
I am trying to limit traffic inbound to 10Mbps on a gig interface 0/48 set to 100/full. So I downloaded some big files over this link and I'm able to see 30- 40Mbps or more. You can see from the show int - rate-limit command that parameters are never showing exceented so nothing has been dropped. [code]
View 3 Replies
View Related
Oct 8, 2012
I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
View 3 Replies
View Related
Feb 13, 2012
As always, the Cisco LMS is keep sending the follwoing high discard error from the Cisco switches WS-C2950T-24:
EVENT ID = 0004SX3
ALERT ID = 00019LF
TIME = Tue 14-Feb-2012 08:56:35 GMT
[Code].....
View 4 Replies
View Related
May 14, 2012
I seem to have managed to set a 2960 to 230400 baud in the boot loader. Is there anyway to reset the variables in the boot loader? Maybe a set of pins to short? I can't access the console port reguardless of what I set the rate too. I've tried both the USB console cable and a USB to serial. Is there anything I can do short of an RMA?
View 4 Replies
View Related
Jan 9, 2013
Here iis a diagram of my current lab where I am using IP SLA to automatically switch from ISP 1 to ISP 2 should the connection go down (and vice versa)
My switches are C3550 Layer 3 switches. Both ISP's do work so connectivity is not the problem.
If I shutdown the fa0/19 port on SW1 the SLA kicks in and changes my defualt route out 10.0.1.0 without a problem. And when I do a no shut it comes back to tge 192.168.10.0 netowrk just as we would expect. No problem there.
When I disconnect the ISP 1 cell phone the SLA does switch the defualt route to the 10.0.1.0 netowrk. Okay, just fine so far. Here isthe problem, when i reconnect the cell phone the SLA does not come back to the 192.168.10.0 netowrk without first having to delete the SLA and then recresting it (both switches).
View 8 Replies
View Related
Jan 15, 2012
I had to format flash and recover. I did the quicker way by using set BAUD 115200...once the .bin was across I forgot to set the baud back to 9600. I have followed instructions: go back to switch: set BAUD 9600 then reset. also tried the unset command. problem is it always comes back up with a BAUD of 115200. CWill I have to label 1 switch as 115200?
View 38 Replies
View Related
Jan 14, 2013
I am trying to recover a corrupted ios, from rommon after configure all steps of IP_ADDRESS, TFTP_SERVER and so on, copy files correctly, but after it need router 5 minutes to erase flash, or something else....after it i can not boot from ios loaded as i show below:
!!!!!!!!!!!!!!!!!!!!!!
File reception completed.
Copying file /c2600-advsecurityk9-mz.123-11.YZ2.bin to flash.
Erasing flash at 0x61fc0000
program flash location 0x60ea0000
[code].....
View 1 Replies
View Related
Aug 2, 2011
We installed a 7200 with a NPE-G1 at a new site and the QOS policy-map is not reporting the correct offered rate. Below is the interface 5 minute rate which is correct and the policy map rate. I am afraid this might through off the measurement on our priority queue policing. It just doesnt add up.
I checked bug tracker and another IOS version...same issue.
disk2:c7200-advipservicesk9-mz.151-4.M.bin"
GigabitEthernet0/1 is up, line protocol is up
5 minute input rate 4000 bits/sec, 7 packets/sec
5 minute output rate 2000 bits/sec, 2 packets/sec
[code]....
View 2 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
Jan 24, 2012
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
View 4 Replies
View Related
Nov 28, 2012
I need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies
View Related
Feb 19, 2013
Currently Being Moderated password recovery
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Oct 22, 2012
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies
View Related
