Cisco Switching/Routing :: Default IOS Image Of WS-C4900M
Jan 11, 2012
I'm not able to find in all the datasheets what's the default (out-of-the-box) IOS image of a WS-C4900M.When I buy a WS-C4900M I know that there is an IP-BASE IOS but which version?
On the datasheet there is a 12.2SG but is an IPBASE with SSH? W/O SSH? UPGRADE SSH? I'm trying to make a comparison between this image and a cat4500e-entservices-mz.150-2.SG2.bin (Advanced Enterprise Services) on the feature navigator to make sure the our customer need this last IOS Upgrade.
View 7 Replies
ADVERTISEMENT
Jul 4, 2012
I have an C4900M with twingig converter and SFP GLC-LX-SMD in. So the SFP supports DOM function. It is running on 12.2(53)SG2.
I would to the see the optical power level of the SFP, but it does not recognize 'show interface transceiver' command as showed in 4500 software guide.
View 5 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Apr 14, 2013
When I config BGP on my 3750X Switch, it show error as below:
protocol not in this image
should I need to upgrade the IOS or Where I can found a supported image (support BGP)
View 1 Replies
View Related
Jan 9, 2013
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies
View Related
Mar 8, 2013
I have 4948E module switch at customer site and below is the show version output. Image on the switch is not supporting 'AUTO QoS' as i need to enable Auto Qos on it to prioritize Voice traffic. Which image supports Auto QoS feature . Image should have L3 functionality also i mean it should support Routing protocols. I tried to enable auto QoS using by configuring "QoS' globally but no luck...with existing image.
{ URL}
ROM: 12.2(44r)SG9
Hobgoblin Revision 20, Fortooine Revision 1.22
Switch up time is 12 hours, 1 minute
System returned to ROM by reload
[ code]...
Configuration register is 0x2012
Switch#sh boot flash:
-#- --length-- -----date/time------ path
1 25793234 May 31 2011 15:20:20 cat4500e-entservicesk9-mz.122-54.SG.bin
2 25005209 Mar 08 2013 09:53:18 cat4500e-entservices-mz.122-54.SG1.bin
70033408 bytes available (58249216 bytes used)
View 1 Replies
View Related
Oct 31, 2012
I wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies
View Related
Feb 29, 2012
i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies
View Related
Dec 2, 2012
We've ordered a 4500 core switch and 4948 Server Farm switch for our client, but the switch box does not include a IOS image CD or anything related to IOS image and now the client is asking us why is this item missing as the IOS
-S45UK9-32-1502SGCAT4500e SUP7e Universal Crypto Image
-S49IPB-12253SGCisco CAT4900 IOS IP BASE W/O CRYPTO
View 4 Replies
View Related
Aug 24, 2012
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
View 1 Replies
View Related
Aug 7, 2012
I own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies
View Related
Feb 15, 2012
I have a simple question: In 6500 CatOS, we had that feature of image synchronization, which added the ability to download the image from the active supervisor to the standby via internal TFTP of the CatOS. Can this be done on IOS? I was looking fot this over the Internet and couldn't find anything.
View 1 Replies
View Related
Dec 14, 2012
I have a cisco 6503 - e series switch which runs c6sup22-psv-mz.121-26.E4.bin. Both superviser engine and MSFC2 card run the same IOS image i guess. In my boot flash their is another image c6msfc2-jsv-mz.121-4.E1. o what is the difference between these images c6msfc2-jsv-mz.121-4.E1 and c6msfc-boot-mz.121-4.E1.
View 5 Replies
View Related
May 13, 2013
I'm having difficult getting this switch to boot from flash. I do not understand why it is trying to load "b1" from "bs1" instead of something from flash. [code]
View 2 Replies
View Related
Apr 24, 2013
I have L3 switch 3560 v2 cisco switch. If i connect the switch via the console cable in XP system i am not getting any responce. I think i need to install via XY mode.
how can i install the ISO iamge via XY mode in cisco switch 3560 v2.Cisco Model: WS-C3560v2-48tS-S.
View 10 Replies
View Related
Jun 12, 2012
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
View 5 Replies
View Related
Sep 10, 2012
i am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies
View Related
Jan 8, 2013
I am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
View 14 Replies
View Related
Jan 8, 2012
Customer has ordered the following routers, which will go in three separate locations.
1. 3945 W/SPE150, IP Base Image
2. 3945 Voice Bundle, includes PVDM3-64 and (1) 2-port T1 MFT
3. 2911 IP Base Image.
If the customer wants to move the Voice image from the existing 3945 to the 3945/WSPE150, would he just need to contact Cisco Licensing, or would the customer have to pay for a software upgrade on the 3945/WSPE150?
Same scenario, except moving the Voice Image to the 2911 router.
View 5 Replies
View Related
May 18, 2013
after upgrading IOS image to V15 on four 2960S switches: Should I make the boot loader image to match the IOS version?I never thought about this while upgrading IOS image unless there is boot issue. I googled for answer but no luck there...
I checked download section on Cisco.com for C2960S-48FPS-L switch and there is simply no boot loader image..The running boot loader is C2960S-HBOOT-M Version 12.2(55r)SEThe running IOS is: 15.0 (2) SE2.
View 7 Replies
View Related
Mar 17, 2011
I inadvertantly copy the wrong image on to a 35609-X switch and now it gets stuck in a particular mode.
The original image was: c3560e-universalk9-mz.122-53.SE2/c3560e-universalk9-mz.122-53.SE2.bin and I replaced it with: c3560e-universalk9npe-mz.122-55.SE1.bin ( this is what the download site identifies as the image for 3560X-24P-S)
It now sticks at: Front-end Microcode IMG MGR: Programming device 0...rrrrrrwssssssssssssssssssspssssssssssssssss
How can I get back on to delete this image? It ignores the break key.
View 5 Replies
View Related
Apr 25, 2013
find what feature set is supported on this IOS S45EUK9-33-1511SG The client requires Layer 3 functionality so do i need to apply any license with it or it will perform layer 3 routing (like rip, ospf, bgp, ipv6, ospfv3) ?
View 1 Replies
View Related
Jan 20, 2013
What features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies
View Related
Nov 15, 2011
I was trying to upload image to sup x4516 V10G from Rommon using the management port but did not succeed. The steps which I did as mentioned below: [code]I got the tftp request on the tftp server but from the switch was showing access violation
View 0 Replies
View Related
Apr 8, 2013
We have a N5K-C50510P-BF. When these nexus starts that didn't booting any further than the kickstart. Here's the boot sequence log
User break into bootloader
Loader Version pr-1.3
loader>
[Code]....
View 0 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Nov 19, 2012
I'd like to know if is it possible to load lan base image on Cisco Switch 2960 TC-S. This model (WS-C2960-48TC-S) come with lan lite image and it's the same (phisically) of the 2960 TC-L (lan base image).If I try to upload the lan base image on flash of 2960 TC-S will works?? ..or the switch goes damaged?
View 2 Replies
View Related
Oct 31, 2011
I've 3750X switch that isn't loading email. then I went to rommon mode and accidently for "format flash". after that I loaded 15.0 SE2 s/w on it using tftp server but it doesn't boot up with that image. flash had only .bin file after I loaded it from tftp server.
since it wasn't booting up, I did format flash again and thought to load image again from tftp server but now, it doesn't load image from tftp server.
View 9 Replies
View Related
Jan 22, 2008
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies
View Related
Jun 10, 2012
whether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies
View Related
Nov 9, 2011
End user have had problem with IP phones that are connected to 3750 stack; many times IP phones lose connection with CallManager and the only way to clear this issue is with clear arp command. DHCP for IP phones is configured in 3750 stack.
At the beginning 3750 stack was set a VTP server, and the others as VTP clients, we detected another VTP server switch so we thought that was the problem, but after removing the issue remains. Finally we set all switch in transparent mode.
Base on this we decided to change the software image 12.2(35)SE1 C3750-ADVIPSERVICESK ---> 122-53.SE2 IPSERVICES I'm going to follow the procedure 3750 Series Switch Stack IOS Upgrade − Automatic .
as it show in the following information there are 4 differents models of 3750 switches, I have already download c3750-ipservicesk9-tar.122-53.SE2.tar for 3750G-24TS.
I have two doubts:
1. There is no problem for using this tar file for all models?
2. I followig command is correct for the change I plann to do ?
Switch#archive download-sw /allow-feature-upgrade /overwrite tftp://192.168.0.24/c3750-ipservicesk9-tar.122-53.SE2.tar
#sh inventoryNAME: "1", DESCR: "WS-C3750G-24TS" 16MB Flash 128 DRAMPID: WS-C3750G-24TS-E
[Code].....
View 3 Replies
View Related
Oct 12, 2011
I have just taken over the management of a Cisco Catalyst 6540. The os image has been erased from the switch (as I have just been informed) and that we need to install the os ourselves.
Any hints on how to install the OS on a switch with no OS installed!
I've started reading on the Internet but am currently confused by "supervisor/msfc", "Cisco IOS/CatOS" and "hybrid/native".I think that we would want ideally to install Cisco IOS using the Native Mode but how would I go about doing that?
View 14 Replies
View Related
