Wireless Connection - Service Not Available After Switch To Windows 7
May 14, 2011
Windows 7 with wireless adaptor connection
I switched to Win. 7, because XP getting slow in general. I've using the brand new Netgear wireless adaptor on Win.7 while the older wireless adaptor is still on XP, but I never use XP after switch to Win.7.
On XP, Wireless connection had no issue at all, however on Win.7, the wireless connection often saying 'not service available' at the right bottom corner.
On XP, Netgear was 150 and Win 7 is 300.
Just wonder whether I should take off the wireless-adaptor from the XP if that would work to boost the wireless connection on Win.7?
View 1 Replies
ADVERTISEMENT
Apr 5, 2012
For some reasons my laptop "lost a wireless connection to the internet. Basically each time I try to connect I get the following message "The window wireless service is not running on this computer.On the other hand If I connect directly to the modem I get internet connection.
View 8 Replies
View Related
Jan 18, 2012
A client is using Tmobile VOIP using the aforementioned WRTU54G-TM 2-line VOIP wireless router with 4-port hub. What they would like to do is to place this in their network and NOT have it change (route) the network addresses being assigned to devices 'behind' this router so even their wireless devices are all "on the same network" as the wired devices BEFORE this unit, In essence, preserve the same 'network and subnet mask' that is being issued by their DSL router via it's integrated DHCP server. ... Rather like operating this unit like an 'access point' instead of a router.Under most circumstances, I might try to assign this router a static IP outside the scope of the DHCP range the DSL router would supply, then plug the (gigabit) Ethernet network cable into one of the 4 Ethernet ports on the rear of this router - but apparently this does not 'facilitate' a connection to Tmobile's VOIP service.When attempting to do this, the connected telephone devices do not get a phone line connection and the status light(s) that normally indicate proper operation do not illuminate.
View 3 Replies
View Related
May 9, 2012
Inspiron 1720 lost wireless connection after Service tech had me reboot Wireless router for other issue not relating to this computer. Now when I look for wireless connections can not find any. Hard wire works fine. Trouble shoot states there may be a problem with one or more of my network adapters. Not very computer savy....But did find a way to run a Ping test and pass. Clicked on my 1502 Draft 802.11n WLAN Mini card and it states this device is working properly. Opened Broadcom control suite and it shows a Red X on the intergrated controller and the wireless card. with option to run a test or explanation of the Red X.
Do I need a new card or is there something else conflicting with it.. I find it hard to believe the card crashed right when I rebooted the Router...ISP sent a tech out but was not able to find problem.
View 7 Replies
View Related
Dec 25, 2011
I keep seeing this pop-up on the firewall (from both source & destination hosts) What app/service uses 47727 on Windows 7?
Edit: It shows up as UDP occasionally, too.
View 2 Replies
View Related
Mar 11, 2013
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies
View Related
Jan 17, 2011
when i trying to share on window xp based computer and access to another computer it givs the message " The Server service not started
View 9 Replies
View Related
Dec 7, 2011
I am running Windows XP. The machine used to be on a Domain, but I took it off. Now, when I reboot the machine, the Server service is gone, and I have to get it back buy Uninstalling then Reinstalling Microsoft File and Printer Sharing in the internet connections dialog. Is there some security policy or something that prevent the Server service from running at boot?
View 7 Replies
View Related
Feb 23, 2013
I've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows
Current OS: Windows 8 PRO
Model: ASUS K43SV
View 1 Replies
View Related
Dec 2, 2012
My HP laptop was working perfectly using wireless Internet but after an update of the SERVICE PACK 1 it now isn't working. It connects to the Internet but it says 'LIMITED ACCESS'. It's clearly something to do with that update as the Internet works perfectly on all over devices in the house
View 3 Replies
View Related
Mar 19, 2012
can you enable dhcp service on a 3560 switch.
View 3 Replies
View Related
Mar 15, 2011
i have a server with windows server 2003 that SQL server 2008 is installed on it.regulary server service will be stoped automativcaly and all shared folders will be unshared and i must restart server and waiting for next stop and .
View 1 Replies
View Related
Feb 15, 2013
I've been able to duplicate my problem by using another WinXp computers instead of a USB drive plugged into my router. Same exact problem. So, the bottom line is that I can access (and modify) the files across the network if I'm doing so manually, but my Windows service fails when trying to do the same thing. If I run the program through Visual Studio, it works. If I run that same exact code as a Windows service, it fails.
I've created a Windows service that needs to access a common network location. To test it at home, I plugged a USB drive into my Netgear N600 WNDR3400 router. The USB storage settings show the workgroup name as Workgroup, and the file path is. [code]
View 1 Replies
View Related
Sep 25, 2012
My Network Layout is as, Firewall (with Routing)------>Cisco 3560 Switch (L3)------> connected 8 Cisco 2960 switch (L2)----> all users I have configured 20 VLAN's on cisco 3560 switch with Dynamic Pool and Static, Means, 5 Vlan's are Dynamic and remaining are Static Our Company process provides only internet access to existing clients computers. Problem is that, I configured Static VLAN 5 for one of our Client in their seperate room, mean to say, i activated all ports of their room with Static VLAN 5. one day they configured own DHCP server on Windows 2003 Server with same subnet (Same as VLAN5) in their room without any information and now their all computer/ Laptop acquiring ip address Dynamically.
If i have configured Static vlan on that port's then how it is get Dynamic ip from same port's.How to restrict to permit another DHCP server/Service in our premises. I Do not want to give administrative control to Clients to do such kind of thing with LAN.
View 8 Replies
View Related
Jul 5, 2010
I just upgraded my ACS v4.0 to the latest available version v4.2(1) build 15 patch 2 and I've got some trouble with the CSLog service. I performed a successive upgrade first to v4.2 then to v4.2.1 and finally applied the two patches. Everything is working fine, I'm using both radius and tacacs services and they doing great like they were in v4.0. The only problem I have is with Cslog service which doesn't start. To be accurate, it starts but stops just after. I've uploaded some logs from cslog.log in cslog/logs directory.
View 6 Replies
View Related
Feb 5, 2013
Since a few days, when I go on Web with my cable connection, the pages of sites stay on a blank page and that does not connect. Having made diagnose, I had the following message:The distant ring road(peripheral) or the resource does not accept the connection.The ring road(peripheral) or the resource [URL] is not configured to accept the connections on the port " Web Service (HTTP) ".I phoned at my FAI ( Videotron) and having discussed for a long time, it happened at the conclusion that it was a problem of router (when I connect the computer directly on the modem, that works very well).Of an other one quoted(esteemed), a connection Wireless telegraphy works with no problem at all, fortunately because I shall not be here.I am to go to my router D-Link Dir-835 and I returned to the former(old) protection(saving) of the configuration. And now that re-works again. But the enjoyment was short-lived because this morning, the problem returned.What do you think about it? I Should make a reset of my router even if it means re-configuring everything again?
[URL]
View 2 Replies
View Related
Jul 9, 2012
I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?
View 1 Replies
View Related
May 16, 2011
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq
[code]...
View 8 Replies
View Related
Aug 28, 2012
My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.
View 1 Replies
View Related
Sep 14, 2011
How to merge two Internet connection services to one faster Internet connection service?
View 3 Replies
View Related
Feb 28, 2012
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
View 10 Replies
View Related
Sep 16, 2011
I have a work computer...Dell Latitude 6400, AT&T Global Network Client (Company VPN service), using Novatel USB551L from Verizon, with their new 4G LTE. First connect to Verizon, then it automatically launchs ATT Global Network Client, once connected, the system automatically maps drives. I stay on for about 15 minutes average to 40 minutes that's when the Verizon drops/disconnects. This consistantly happens throughout the day!
1. If I connect to a "local" wireless signal NO dropping.
2. If I tether my Sprint Android, NO dropping.
Only dropping with the Verizon. I MUST have the Verizon dedicated to this work computer to run the VPN and hopefully (very soon) a mandated VOIP with Avaya!Called Verizon- they sent me a new USB thinking that might fix it. But same thing. They are showing signal strength 4G. Nothing on their side.
View 1 Replies
View Related
Apr 2, 2012
i have tryed starting it on the services but that willl not do it eitheir. i have tryed almost everything and it stilll does not work. i can not access internet. plus i think a virus messed up my internet protocols. i think i removed the virus though i have been looking for an answer for 7 hours now
View 1 Replies
View Related
Feb 24, 2013
Is it possible to establish a connection to an IPTV service with the N150 wireless router?
View 1 Replies
View Related
Jul 1, 2011
I am running windows 7 home premium 64bit and have a wireless connection. Can I connect a switch to my LAN port on my PC and share my network connection with other devices? Would it operate as a standard switch would operate coming from a router?
View 1 Replies
View Related
Mar 25, 2013
I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
i tried pdshow -brief ANIServer ===> service UP
DNS is working using host file in driversetc i restarted the server
restared the crmdmgtd
unistall / install java plugin
pdterm ANIServer
pdexec ANIServer
NO change ..
View 6 Replies
View Related
Aug 3, 2011
Current network configuration is as follows:Internet -> Router -> 24port Switch (main switch)I have seven network segments, connected to the main switch via 8port switches.Just to clarify, all the segments are in the same subnet.One of the segment, has a wireless N router connected to the 8p switch. The wireless router, actually functions as a wireless switch rather than performing any routing.Occasionally, the segment with the wireless looses network connectivity. When it looses connectivity, the wireless stops broadcasting and the computers connected to the 8p switch (not the wireless) cannot browse the network shares nor ping the computer in that same segment.All we could conclude from this, was that the wireless router somehow crashed and started jamming the switch, preventing anybody from connecting to the switch.
View 3 Replies
View Related
Aug 18, 2012
I had win7 32bit with working wireless internet.Deleted it and installed Win XP and now there is no wireless internet.Downloaded all kinds of drivers from realtek but nothing works for RTL8139/810x Family Fast Ethernet NIC.
View 8 Replies
View Related
Mar 13, 2011
I recently bought a new HP Pavilion dv6 Notebook PC and have been experiencing problems when connecting to my personal wireless network. It seems that whenever I'm downloading anything or using the connection extensively I'll lose internet connection and the wireless icon in the bottom right hand corner of the screen will show an orange star to indicate that connections are available. However if I go to available networks I can immediately reconnect to the network I was on.
I have other notebooks that run on XP that do not have this issue and use the connection without a problem. Also when I connect my notebook directly to my belkin router via Ethernet cable the connection has issues. I'm running my computer on Windows 7 Home Premium 64-bit and my Wireless adapter is an Atheros AR9285 802.11b/g/n Wifi adapter which appears to have up to date drivers.
View 16 Replies
View Related
Apr 24, 2011
This has been a problem 2 months ago and it is still not fixed My ping sometimes goes up to 500 and disconnects, usually every 10 minutes i disconnect from TeamSpeak3. My connection is 3 bars and drops down to 2 which is when it disconnects . My modem is only 4 meters away from me and another laptop is 2 meters away from it but it has perfect connection. My sister upstairs also has perfect connection. Im using Realtek 8185 extensible 802.11 b/g. Sometimes its worse and sometimes better but only by alittle bit
View 15 Replies
View Related
Mar 29, 2011
Conection between the accwss point,Router, or Cable Modem and the internet are broken. Potential problem, missing IP address.
View 1 Replies
View Related
Mar 21, 2012
I have a netgear wna1000m g54/n150 wireless usb adapter. and cannot get it to see my westel at&t network. Adapter is working right in control panel and i can connect to the internet via cat 5 connection but does not see the network with this adapter. Have troubleshoot with netgear and at&t tech's for hours no luck, changed out adapter to a belkin same problem got another gateway and still win7 will not work, something is blocking my connection and gateway checks out and adapter is installed and correcother info to pass on this is very tough and just got the dsl and have not been about to enjoy this desktop with wireless yet hp system bout 7yrs old and working good so any of you have some suggestions that would be beond the norma
View 43 Replies
View Related
Jul 24, 2011
I already uninstalled norton internet security also. Im using a sony vaio windows vista intel pentium dual cpu T2330 @1.60Ghz with ram of 1014 Mb and a system type of 32-bit Operating System.
View 1 Replies
View Related
