D-Link DIR-825 :: No Connection On Port Service Web (HTTP)
Feb 5, 2013
Since a few days, when I go on Web with my cable connection, the pages of sites stay on a blank page and that does not connect. Having made diagnose, I had the following message:The distant ring road(peripheral) or the resource does not accept the connection.The ring road(peripheral) or the resource [URL] is not configured to accept the connections on the port " Web Service (HTTP) ".I phoned at my FAI ( Videotron) and having discussed for a long time, it happened at the conclusion that it was a problem of router (when I connect the computer directly on the modem, that works very well).Of an other one quoted(esteemed), a connection Wireless telegraphy works with no problem at all, fortunately because I shall not be here.I am to go to my router D-Link Dir-835 and I returned to the former(old) protection(saving) of the configuration. And now that re-works again. But the enjoyment was short-lived because this morning, the problem returned.What do you think about it? I Should make a reset of my router even if it means re-configuring everything again?
Foreach computer I need to go and configure the browser proxy settings and some people are getting smart and turn it to automatic configuration again.
So what i want to achieve is to have my DIR-655 to route all the HTTP/port 80 traffic to the proxy server. That way it is transparent and then it is not needed to configure each computers browser settings.
I am pretty new to this and the router configurations.
The proxy server works fine if i configure the browser manually.
We have ASA5520 and we want to configure a VPN IPSEC profile so that a partner of ours can access only a server and only on HTTP port.I've tried configuring split tunneling with an Extended ACL but probably I'm missing something. I just configured the ACL so that it included any source to our server's IP on HTTP port but when testing, it didn't work.
However, if I configure a Standard ACL on the split tunneling I can access the server and all the services it provides.Do you know if I'm missing anything on the Extended ACL configuration?
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
I need to redirect all http and https traffic from one source in a dmz network, to port tcp/8080 on a proxy server on the inside network.
The source device doesn't handle proxying very well, so i've been advised to redirect the tcp/80 and tcp/443 ports to tcp/8080 as it passes through the firewall.
I need to configure a keepalive that check an url in a server (http in port 9500 not in port 80) and check the port 443 in the same server. If any of them not response . the service should go down.
1.I use it as a AP, no connection in the internet port, however I only see the DNS setting in the WAN interface, so some url setting can not normally run. Do it has AP mode or other setting that can resolve the DNS.
2.I notice that the Time will suddenly wrong something, even I set it to use local time or ntp.
3.I change the wireless setting to WPA Enterprise, and notice that always disconnect and reconnect, When it is disconnect, notebook and phone can not search the wireless, but ping in local is still alive, log also only show that reconnect, what is happen?
4.I run the internet wizard (not at beginning), I do not change new password in the second phase of wizard, however, after the end of wizard, restart the DIR 655, I can not use the password I set before to login and also I try to leave blank in password flied, it also failed, I use the same password in the user(not admin), I can login, is it the bug of wizard, if this situation need to reset the router, can I take the config first?
I recently bought a EA6500 to replace a EA4500 (defective). Prior to the EA4500 I had a 160N which I now use as a WAP for 801.11G devices. I thought the 4500 was good from the media server functions it offered.However since installing the 6500 I noticed:
1. I have port forwarding for http to a web server. It works fine from machines on the outside but from my local subnet 192.168.1.x I can't access the web server (I can't even ping the external address - and yes I turned the anonymous filter off). I am not using ddns and I have a static ip address (cable modem connected) to the outside world.
I need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
We are testing a Zone Based FW config since 1month, everything run smooth but we're having problem ( big slow speed access ) when a user try to reach a website on a non-standard port ( 8080 in that case ). All the trafic stay in our LAN, using a IPSEC/EZVPN connection between the 2 sites.As soon as I have disabled the Zone Based FW, the speed was much better.
I'm sure I'm missing a parameter to fix that problem but I tried many different options and I didn't find anything yet. All the routers are Cisco 1811 running adv IP Services 15.1.2.T1 IOS.A port-map has been created to map the port 8080 to the HTTP protocol for the inspection.The PC will have an IP address in the 10.2.2.x/24 and will access a server on 10.2.3.x/24, both devices are part of the zone private in each site/LAN.All the access between sites are managed by an ASA; the IPSEC/EZVPN peer.Little summary, it's gonna be something like : SiteA with a PC on private zone then on public zone for the EZVPN to SiteB on public zone and then private zone to access the server in the LAN.
I installed the DIR 655 router using the install disk. I hooked up my Vista desktop machine via the ethernet port. I also activated a Roku box and my Itouch successfully via the wireless.I turned MAC filtering on and manually entered the MAC addresses for the three devises. Everything worked fine.After I rebooted the desktop, I could no longer get to the internet via the desktop connected through the ethernet. The Roku Box and I-Touch both work fine and enjoy a strong wireless connection.I've tried rebooting the desktop several times, but still can not access the web. I also can not access the router by typing in 192.168.0.1. I entered the configsys stuff and verifited that I am using the right numbers.
The Port 80 port fowarding stops functioning after a few hours and requires the router to be rebooted to start forwarding again. The firmeware is the latest 1.0.04 Build 7. I require it to operate reliably for many days without intervention. I assume that it is a port forwarding problem because I can access the IP on my network from within my network even when I can't access it from outside my network. I am using the correct IP addresses as it sometimes works OK. A characteristic is that when I can't access the page it loads as completely blank white with no error message.
I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map parameters message-length maximum client auto
I've configured my 655 and I can access the internet through it. Network cable from PC goes to the DLINK, DLINK to the DSL modem, DSL modem to the big scary internet. This all works great. Now for the Wi Fi.I've set up the Wi Fi on the 655 and can both see and connect to my newly configured home network from my laptop, but I can not access the internet from the laptop.
I have tracked about 7 unique IPs originating from China where these scans for accesses to my network are causing 2-10secs of downtime in realtime gaming. Never had this problem when I was using Firmware 1.34NA. Stuck with 1.35NA and its causing lots of eyesores even though Wifi has been great with my laptop and phone for N/G. I only keep my main PC on and my 2 fileservers are offline until need to start archiving data or fetch something from them. Wifi is disabled until I need my laptop and phone. I personally had my ISP do an inhouse checkup and fixed some splitter issues and a new coax cable so signal issue is fine. Motorola 6120 Cable modem. Was pushed to contact my ISP Abuse group to figure this out but it might be a lingering issue for awhile.
As the subject says, I've hooked up a Samsung BD player to a BEFSR41 router. The router has the current firmware version. When I run the connection test for the player, the local connection is good but the Internet connection fails and the message is " The HTTP port is disabled."
I've searched high and low for a solution to no avail. I did searches on the forum and couldn't find anything. As a test, I connected the BD player directly to the DSL modem and the Internet connection worked perfectly so it appears that the blockage is within the router.
I've serched through the router setup and have changed most settings to try and find something that would work. Nothing worked so I have returned my setup to its original state.
Firmware version 1.3.3.5 STAR 9202 Chipset 64 MB DRAM 8MB Flash DOS, Block WAN Rq, Remote mgmt all OFF IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
Region : Germany Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 121127
is it possible to use the Print Server on the TL-WR1043ND without installing the "Printer Controller Utility"? I have a HP LaserJet 1022 (in compatiblity list) connected which is recognized by the TL-WR1043ND. I want to connect the printer manually to my Windows PC using standard tcp/ip port, but I can't get it working. I tried RAW with Port 9100 and LPR with lp1. What are the right settings??
I currently have a vlan/SVI on my 6506 for the WiSM service-port. The WiSM has an address on the same subnet. To manage the WiSM, I either https to the Management interface address or use 'session slot X proc Y' from the the 6506. Since I am essentially only using two addresses from a subnet for this service-port I would like to free up the subnet. Can I keep my current functionality by having a vlan only (with the wism service-vlan XX command) with no SVI?
I have a 4402 and recently I have not been able to access the device via the service-port interface. The service-port has an IP Address and it is connected to an access port in the Vlan which I am coming from, however it cannot even ping it's gateway, which as mentioned is within the same network. When I am at the console of the controller I can ping the service-port interface IP that I have assigned, just nothing else.
I recently configured CISCO 3310 box with MSE version 7.2. Services are up and running in the box, I could add the MSE to WCS and also able to track the location using WCS. However, I could not connect the third party software to MSE web services to get the location information there. When I hit the server url "https://<my mse>" I get list of possible services like:
Error 404 - Not Found.No service matched or handled this request. Known services are:
I browsed through the documentation (CAS_71.pdf) and found a text saying:
Note Port 80 will be enabled on the MSE if the enable HTTP command was entered on MSE. Ports 8880 and 8843 will be closed on the MSE when the CA-issued certificates are installed on the MSE. I am running the test system so I do not really want to install CA signed certificate, so I used self signed certificate and restarted the server, but it did not work.
We are trying to set up Out of band connection for Cisco 5508 WLC and when we try to ssh to the Service port from a remote switch, this fails. SSH or Telnet to the Management IP address works fine. The Service port and Managment IP are in the same IP scope but different subnet..i.e 172.16.10 for Management and 172.16.99 for Service port. Also, as this set up will be HA (AP SSO) in future, for which DHCP is recommended for the service ports, just wondering if SSh will be possible.
I have Site(s) Ani....i=1,..10 sites which communicate with site B to access a website/application. That's simple enough. However, the traffic is http well we primarily don't need https on ipsec tunnel right?. But since attacks related to eavesdropping of traffic come a real reality once it gets terminated by the ipsec device on both side.I have two options either to purchase a third-party ssl certificate to encrypt the traffic between two nodes or use a custom made one.I don't want to use a custom made one because this make the browser prompt an ugly untrusted certificate message; its ugly not from security perspective but for clients inconvenience and assuring users confidence in our systems is a critical issue for us. ?
a) How its possible to remove ugly certifcate message from user screen? Does the company need to register its certificate to some kind of CA body? or what ...
b) Due to some tcp acceleration issues, ssl traffic slows down the traffic between the nodes so we only require the encryption to stand just during the initial handshake when the username and password are being validated ; after that we want to revert back to http?
Goal: To forward requests over port 80 from my LAN to an external server on a specific port, that is I would like to forward all requests over http to an external proxy.
I know that this can be done with IP-Tables, but I would like to do the same thing with my D-Link. I have looked at Advanced --> Routing, but that seems to be specifically for inbound requests. I want to do this for outbound requests. This can be achieved with the D-Link DIR-655?
Region : Australia Model : TD-W8968 Hardware Version : V1 Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n ISP : Bigpond
I am trying to setup port-forwarding (6360 for IP 192.168.1.111 & 6361 for IP 192.168.1.112) on this TD-W8968 modem. But when I test it on [URL]. I get a message "connection refused".
I am replacing an old Fw with a New ASA 5510 and I have a problem with a TCP Connection on My LAN InterfaceI joined a picture of what I want to do. [code] From the PC,I can Ping the Video Camera But I can't connect to it with HTTP.I don't understand, Packet Tracert allow the Http packet too. [code]
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
I am trying to set up a custom service on my netgear configuration page. I have a netgear router model# Wnr834m. every time i click the "add custom service" button the page redirects to "system authentication failed" and logs me out. What can i do to set up the new port?
I've been configured my device to forward FTP service to my server, however, I can't access this service outside from my network. I used Single Port Forward and not worked, after, I've used Port Range Forwarding starting in 20 to 21 and not work again.I've sniffed my computer and I've found just 3 outsides packages without response.I've tried with directly IP ADDR and DYNDNS ADDR, but neither one or other worked.
