Linksys Wireless Router :: E2000 HTTP Port Forwarding Stops After A Few Hours?
Aug 6, 2012
The Port 80 port fowarding stops functioning after a few hours and requires the router to be rebooted to start forwarding again. The firmeware is the latest 1.0.04 Build 7. I require it to operate reliably for many days without intervention. I assume that it is a port forwarding problem because I can access the IP on my network from within my network even when I can't access it from outside my network. I am using the correct IP addresses as it sometimes works OK. A characteristic is that when I can't access the page it loads as completely blank white with no error message.
View 2 Replies
ADVERTISEMENT
Jan 7, 2013
I recently bought a EA6500 to replace a EA4500 (defective). Prior to the EA4500 I had a 160N which I now use as a WAP for 801.11G devices. I thought the 4500 was good from the media server functions it offered.However since installing the 6500 I noticed:
1. I have port forwarding for http to a web server. It works fine from machines on the outside but from my local subnet 192.168.1.x I can't access the web server (I can't even ping the external address - and yes I turned the anonymous filter off). I am not using ddns and I have a static ip address (cable modem connected) to the outside world.
View 2 Replies
View Related
Jun 10, 2011
I recently purchased a Slingbox PRO-HD and the iPad software to view HD on my iPad when I'm away from home. When I setup the Slingbox using their web-based configuration program, it reports that I do not have my network configured for the best performance for internet viewing, which is what I need for the iPad. I suspect that I don't have port forwarding for port 5001 correctly setup on my system. I can successfully connect to my Slingbox away from home on my iPad and my laptop, but the performance is indeed poor.
I have a cable modem and two E2000 routers. The first E2000 is connected to my cable modem in my home office and the second E2000 is in my home theater. I used Cisco Connect on separate PCs to setup the two routers. Here are the details:Cable modem:Scientific AtlantaModel DPX2203 SeriesPart number 4006351'Ethernet' connected to Router 1 'Internet' connection.
Router 1:Cisco LinksysModel E2000IP address 192.168.1.1Wireless enabled.'Internet' connected to Cable modem.'Ethernet' connections:1. Seagate network storage drive2. Desktop PC3. Desktop PC4. Router 2
Router 2:Cisco LinksysModel E2000IP address 192.168.2.1Wireless enabled'Internet' connected to Router 1 'Ethernet 4' connection.'Ethernet' connections:1. Slingbox PRO-HD2. Desktop PC3. A/V Receiver4. Blu-ray player
How do I setup port forwarding for the Slingbox PRO-HD on port 5001? Also, what is the best way to setup two E2000 routers so that I can use both as wireless access points?
View 5 Replies
View Related
Jul 15, 2011
I was wanting to port forward a port that was 25565 for a game of mine, but everytime I try it won't work.
By the way, it's 7AM and I didn't sleep yet so i'll explain more detailed in the morning.
I'm using a E2000 Router.
View 1 Replies
View Related
Jan 2, 2012
I currently have cable internet connected to one router (Linksys E2000 w/ firmware v1.0.03). That router is connected to another router, a Linksys E3200 w/ firmware v1.0.02. In order to properly forward ports through the E3200, I understand that I need to set up a static IP on that router.I've basically followed the steps outlined in this video, but when I enter all the IP addresses for Static IP settings, it won't allow me to access the router's setup page. I try entering the new IP that I've given it (which it tries to direct itself to automatically after I save the settings) and the connection times out. I am able to access the internet otherwise, however. From here I'm forced to do a factory reset on the router and start from square one.
View 6 Replies
View Related
Jul 31, 2011
So currently I'm having issues with changing my nat type to open for my ps3. I've tried to use DMZ and port forwarding to change the nat type, but sadly I couldn't get this to work. Most the guides on the forums are for xbox's which wouldn't work for a ps3. Any handy guide to change my nat type to open for my ps3?
View 5 Replies
View Related
Jan 16, 2010
Having a problem with port forwarding on their WRT400N? I'm forwarding one service (https) and this stops working if it's not accessed after a 10 days or so. The only way to get it to work again is to reboot the router. I’m running the “latest" firmware, which is an oxymoron considering it's been over 12 MONTHS since Linksys updated the code... Which is appalling considering this appears to be their flagship wireless N router.
View 5 Replies
View Related
Jul 15, 2011
I've been wanting to port forward this game called Minecraft for quite awhile now, but never got around to it, but now that I've wanted to let my friends that can't play with hamachi play with me. I wanted to port forward it so that they go into the game without using hamachi, or any other networking program. I've already tried once and whenever I ran my server, I would say "FAILED TO BIND TO PORT" or just ask me this "Is another running on that port?"
View 9 Replies
View Related
Oct 21, 2011
I have a Cisco Linksys E1000 wireless router. It has been working perfectly for the last few months until yesterday when I noticed none of my wireless devices could connect. The SSID was still being broadcast and my computers that were connected through an ethernet cable were still able to access the internet fine. Eventually I pressed the red reset button on the back of the router, which reset my router name, password, etc. I set everything back up and was able to connect again. Several hours later the wireless stopped working again. When I launched the Cisco Connect software I was prompted to update some software (possibly the router firmware) so I did that. After that I was able to connect to wireless again. This morning I woke up and wireless was not working again. This time I changed the password for the router and then I was able to connect to wireless again. I tried to change the router password back to the original password and I couldn't connect anymore. When I changed the router password back to the new password I could connect again.
View 1 Replies
View Related
Dec 2, 2011
I have a philips tv 9000, qnap 210, twonky and e2000. When i using my e2000( wireless/cable) the tv stops playing the vids after 5 min.When i using un very old smc router there's no problem.
View 6 Replies
View Related
Feb 4, 2011
I am using DIR-655 A4 router and I have a server that needs DMZ and a PC that needs a port.So, I have set the dmz to 192.168.0.100 (SERVER) and set the port 2000(or any) to forward to 192.168.0.2 (PC).What I found out was, the port forwarding works well for several hours and suddenly it fails and won't forward until I reboot my 655 router. I am really tired doing this every day. I tried firmware 1.21 to 1.35 and non of them were good.I know that 655 has good performance compare to its price but I think it has world's worst firmware.
View 9 Replies
View Related
Dec 1, 2012
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
View 1 Replies
View Related
Jan 1, 2011
I have a problem with my wag120n and iphone or ipad or macbook.The connection works well for about 1-2 hours then stops.so with macbook i have to disable airport and connect to the network again with iPad or iPhone i have to turn-off and REturn-on the wifi.I have already changed the wireless channel but this didn't work form me.
View 5 Replies
View Related
Feb 19, 2011
My D-Link DIR-655 will no longer let me pull up any web pages after several hours. For example, it works great when first rebooted, but the next morning web pages have timed out. When it is broken, I'm unable to connect to web pages via another wireless access point that i've plugged into the D-Link. I'm unable to use any of the wireless PCs or devices in my house.After it's rebooted, it works well for at least a few hours. It has the latest firmware and has basic, out of the box settings.
View 14 Replies
View Related
Oct 21, 2010
Running Firmware v. 1.00.19 here, which I reckon is the most recent version.
My network consists of two Macbooks, an iMac and two iPhones. It utilizes WAP2 encryption and all devices are well within range, the environment being free of interferences from any other WiFi signals (this is a rural area).
My problem: Bonjour networking stops working after a few minutes or hours. When the problem appears, WIRED devices can see all other peers in the network (both wired and wireless), but WIRELESS devices cannot see any other peers whatsoever (wired or wireless).
I have heard that this could be because of a faulty implementation of uPNP by Linksys, and in particular a problem with multicast filtering (and unfortunately the modem/router's firmware does not provide any relevant settings). But I am not sure.
I purchased this thing with the express purpose to use it on a Mac-only network, and I am thoroughly disappointed to see that it does not work, especially since UPNP is supposed to be supported.
View 1 Replies
View Related
Oct 25, 2011
I am using a RV110W with the latest firmware 1.0.1.6 I have some port forwarding configured, which normally work. But sometimes, all port forwarding stop working. Everything else continues working normally, just all port forwarding don't work any more. I tried disabling the port forwarding and enabling them again, this doesn't work. Also disabling the firewall completely does not work. You have to reboot the router, then everything works fine again. When I make a portscan from outside with a "fresh" started router, the forwarded ports are open. When the error occurs and I make a portscan from outside, all ports that should be open (and have been open before) are closed.
View 8 Replies
View Related
Oct 6, 2011
After a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
View 1 Replies
View Related
Jun 4, 2013
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
View 1 Replies
View Related
Feb 9, 2010
I have noticed that in my router log that the router opes a port automatically without any human interaction and after some the time router closes the port again.Here is the log file of my router that opens the port and close it after a couple of hours.
LOG------------------------------
Tue, 2010-02-09 10:02:16 - AddPortMapping: external NULL:3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP) with timeout:0Tue, 2010-02-09 10:02:16 - no permission rule matched : accept by default (n_perms=0)Tue, 2010-02-09 10:02:16 - redirecting port 3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)Tue, 2010-02-09 10:02:16 - creating pass rule to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)
.....
Tue, 2010-02-09 12:52:59 - DeletePortMapping: external port: 3658, protocol: UDPTue, 2010-02-09 12:52:59 - removing redirect rule port 3658 UDPTue, 2010-02-09 12:52:59 - Trying to delete rules at index 0
View 6 Replies
View Related
Jun 26, 2012
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies
View Related
Feb 26, 2013
I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
View 9 Replies
View Related
Sep 16, 2011
I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
View 5 Replies
View Related
Nov 2, 2012
I am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.
View 9 Replies
View Related
Nov 2, 2012
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies
View Related
Feb 6, 2013
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
View 2 Replies
View Related
Nov 1, 2009
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
View 9 Replies
View Related
Aug 31, 2012
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
View 1 Replies
View Related
Jan 19, 2012
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
View 1 Replies
View Related
Jan 28, 2012
I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
View 2 Replies
View Related
Mar 30, 2013
I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies
View Related
Nov 14, 2012
Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable
View 1 Replies
View Related
Feb 12, 2012
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies
View Related
Aug 18, 2012
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 Replies
View Related
