I have a problem with my wag120n and iphone or ipad or macbook.The connection works well for about 1-2 hours then stops.so with macbook i have to disable airport and connect to the network again with iPad or iPhone i have to turn-off and REturn-on the wifi.I have already changed the wireless channel but this didn't work form me.
View 5 RepliesI have noticed that in my router log that the router opes a port automatically without any human interaction and after some the time router closes the port again.Here is the log file of my router that opens the port and close it after a couple of hours.
LOG------------------------------
Tue, 2010-02-09 10:02:16 - AddPortMapping: external NULL:3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP) with timeout:0Tue, 2010-02-09 10:02:16 - no permission rule matched : accept by default (n_perms=0)Tue, 2010-02-09 10:02:16 - redirecting port 3658 to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)Tue, 2010-02-09 10:02:16 - creating pass rule to 10.1.1.253:3658 protocol UDP for: 10.1.1.253:3658 to 3658 (UDP)
.....
Tue, 2010-02-09 12:52:59 - DeletePortMapping: external port: 3658, protocol: UDPTue, 2010-02-09 12:52:59 - removing redirect rule port 3658 UDPTue, 2010-02-09 12:52:59 - Trying to delete rules at index 0
Running Firmware v. 1.00.19 here, which I reckon is the most recent version.
My network consists of two Macbooks, an iMac and two iPhones. It utilizes WAP2 encryption and all devices are well within range, the environment being free of interferences from any other WiFi signals (this is a rural area).
My problem: Bonjour networking stops working after a few minutes or hours. When the problem appears, WIRED devices can see all other peers in the network (both wired and wireless), but WIRELESS devices cannot see any other peers whatsoever (wired or wireless).
I have heard that this could be because of a faulty implementation of uPNP by Linksys, and in particular a problem with multicast filtering (and unfortunately the modem/router's firmware does not provide any relevant settings). But I am not sure.
I purchased this thing with the express purpose to use it on a Mac-only network, and I am thoroughly disappointed to see that it does not work, especially since UPNP is supposed to be supported.
I have a Linsys E3200 router for almost a year. It's been working fine until recently. It kept losing internet connection every a couple hours or even shorter. I have to power cycle the router in order to make it to work. However, sometimes that won't work either. I also tried to restore the router to the factory default but that doesn't seem to work.
I have updated the router with the latest firmware (1.04). I am using a cable connection and it never gives me any problem if I just connect my computer to it. I also test my network with another old netgear router that works just fine.
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies View RelatedI have an issue with my current network where every couple of hours I will lose my connectivity and it will not come back unless I do a power cycle on my router/modem. I originally thought the issue was with my router, however I'm beginning to think it's an issue involving the modem. I've tried two different routers and this happens on both. My main router is a D-Link WBR-1310 (crap I know but it was free) and has lasted for years, and my modem is a Toshiba PCX2500 from Time Warner Cable. The second router I used to test this was an older Linksys BEFW11S4. I was going to replace my router, but when I saw that both of them reset after a few hours (today was only 5, last night it was connected for over 8 hours as I slept). I ran an IPCONFIG /ALL when I was connected with internet and when I was connected without and the only three changes were: [code]
View 2 Replies View RelatedI have 2 Router (Cisco WAG120N) and (Micronet SP3364)I am connected to the Internet with MicronetUse Cisco Only ACCESS PointI am putting Cisco on a bridge and OnlyBut I am having problem ... Cisco is always disconnected, but I have internet on the wireless network through the Cisco.
View 2 Replies View RelatedI will just explain my setup:
I have a ADSL Huwavi modem by my ISP installed at my place.. Now the wireless from that device is very bad.. So I purchased WAG120N to setup a daisy-chain kind of setup in my other bedroom. I also put another D-link DIR-600 in between to give a connection to the first floor (via Ethernet cable).
So my huwavi is the ISP device, then a LAN from it goes to the dlink internet (WAN) port. then one cable from the d-link LAN port to the LAN1 of WAG120N and another upstairs.
Now all of this was working perfectly.. I put same SSIDs and Pwds on both ISP router and WAG120N and i was getting seamless net..
Now yesterday we removed the ISP modem to do some shifting.. Upon reconnecting, the ISP modem, Dlink work as before, but the WAG120N refuses to connect to the net.. it shows DSL down and doesn't access the www.
What I felt is that since i changed LAN ports on my ISP device and dlink, the static IP settings on the WAG120N should be changed.. i modified it, set to to point to the dlink for internet and huwavie for DHCP.. yet nothings happening..
I even connected the WAG120N directly to the Huwavie, yet it fails to connect to the net..
I don't know if this because buggy firmware (i updated to V1.00.16) or there something wrong with the device but if i set radio band to AUTO which enable wide-channel, my wireless connection become unstable when i ping to the modem, i got 200ms - timeout randomly
my family notebook that on other side of room connection also become more worst , ping to the modem (192.168.1.1) timeout so often
the connections seems better if i set radio band to standard - 20Mhz channel even though it seems WAG54G2 have more stable wireless connection (i replace it because the ethernet port dead) i also tried to change the channel, but the issue still persist, it seems the default is the most stable (channel 9 for wide, 11 for standard)
should i RMA the product as i just purchase last week? or it just because the bad firmware ?
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
View 1 Replies View RelatedRecently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
I have WAG120N and I want to use ssh tunneling to browse the net.In windows, I have to use a software like putty or xShell to establish a ssh connection to remote server.It works perfectly and I don't have any problem with it.The problem occurs when I want to use this ssh account in linux.At first,connection established without any problem or error.After 2-3 minutes it seems ssh dies and no data transmitted through ssh tunnel.I tried this with Symphony ADSL modem(Wired only) and I have no problem with it.I want to know if there's any specific problem or configuration for WAG120N to solve this problem?I like this modem/router and I don't want to sell it and buy any other modem/ router.I have to mention that usually I use wired connections to WAG120N,but at some cases I need to use its wireless features.
View 4 Replies View RelatedFrom time to time, when I wake up an specific station from sleep mode, the router loses its connection with Internet. It still has the line synced, but there is no Internet connection.I still can access the router through browser though. If I hit "connect" to establish a manual connection, it does not work. I have to switch the router off and on and wait for the whole process of syncing and connection, then I have Internet again.
I thought this could be something on that PC (old XP) sending some weird packet to router when I wake it up, but I tried with a newer PC (Win 7 64 bits) and the same problem persists. Also, this only happens when I wake up the PC. If it is off and I turn on, or if I restart, the problem does not happen.
The router (WAG120N) has an old firmware version (V1.00.12) because the latest available is buggy and had some problem with my ISP (limiting the bandwidth). However, I have this firmware for like 6 months and the problem only started 2 months ago.
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies View RelatedI have a Cisco Linksys E1000 wireless router. It has been working perfectly for the last few months until yesterday when I noticed none of my wireless devices could connect. The SSID was still being broadcast and my computers that were connected through an ethernet cable were still able to access the internet fine. Eventually I pressed the red reset button on the back of the router, which reset my router name, password, etc. I set everything back up and was able to connect again. Several hours later the wireless stopped working again. When I launched the Cisco Connect software I was prompted to update some software (possibly the router firmware) so I did that. After that I was able to connect to wireless again. This morning I woke up and wireless was not working again. This time I changed the password for the router and then I was able to connect to wireless again. I tried to change the router password back to the original password and I couldn't connect anymore. When I changed the router password back to the new password I could connect again.
View 1 Replies View RelatedThe Port 80 port fowarding stops functioning after a few hours and requires the router to be rebooted to start forwarding again. The firmeware is the latest 1.0.04 Build 7. I require it to operate reliably for many days without intervention. I assume that it is a port forwarding problem because I can access the IP on my network from within my network even when I can't access it from outside my network. I am using the correct IP addresses as it sometimes works OK. A characteristic is that when I can't access the page it loads as completely blank white with no error message.
View 2 Replies View RelatedWhen I try downloading from fileserve it starts downloading and after maybe 3-4 mb it stops for no reason also in JDownloader it starts and after 3-4 mb it says no permission to write to hard disk all other filehosts are working fine and all other downloads work perfect.I'm using ESET smatr security but I'm disabling Web access Protection and the firewall is set to learning mode so all attempts of any application to connect to the internet would be allowed
View 1 Replies View RelatedI'm having is that every few hours my TCP/IP protocol stops working. The modem lights remain normal but I can't connect to anything. The only thing that works on the internet is traceroutes at the command prompt which function normally. The solution is that I have to reboot and then everything returns to normal until a few hours later when it happens again. There are no error messages on any of my browsers. The page just goes white immediately. When I try to retrieve my email, I get a message about the TCP/IP isn't working.
View 9 Replies View RelatedI bought my new router WAG320N two weeks ago and each morning after 10 hours operation I loose my internet connectivity I can't even remote into the router and press the connect button to connect to the internet again .I have to power cycle the modem to be able to connect to the internet again .? I though this may be ISP related put my old adsl router plugged it in and ran for 2 days no disconnection.
View 1 Replies View RelatedMy internet (wired and wireless) usually works fine, but occasionally (read: every few days to weeks) the connection will suddenly black out for a period of time, anywhere from an hour to a day. I have tried resetting both my router and modem, and going through all the settings on my laptop, but I'm pretty sure it's not my computer, as no other devices can connect either. During the blackouts, when I look at the modem, the internet light will turn on for a second, then go off and then the red "alarm" light (aka "something is wrong" light) starts blinking like crazy, and this keeps repeating. This resolves itself after anywhere from a few hours to a whole day and everything is normal again. The light show, and the fact that I can't find any other problems, leads me to believe that it could be a problem with my provider (or the network itself) and not a hardware or software problem, but I can't be sure of this.Also, during the blackouts, I can connect to the network, but it shows that limited connectivity symbol (exclamation mark thing) and says no internet.
View 5 Replies View RelatedMy D-Link DIR-655 will no longer let me pull up any web pages after several hours. For example, it works great when first rebooted, but the next morning web pages have timed out. When it is broken, I'm unable to connect to web pages via another wireless access point that i've plugged into the D-Link. I'm unable to use any of the wireless PCs or devices in my house.After it's rebooted, it works well for at least a few hours. It has the latest firmware and has basic, out of the box settings.
View 14 Replies View RelatedI have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
I have a WAG54G2 working fine for more than 2 years now. It has the initial firmware version 1.00.10
Recently I mode it from my home to my store, where I have a already working CCTV setup. Initially the router did not work, but once the service provider removed the mac-id binding (with my previous ADSL2+ router) the WAG54G2 was connecting on DSL. However it never got a DNS value. Currently I am using it with a fixed DNS.
After a few days of working I noticed that my remote viewing for the CCTV was not working. On checking the router settings I saw that the router had defaulted to no settings at all. Changing it back to PPPoE did not work since the page would not render completely. Resetting to Factory settings also did not work. However simply switching off the router and restarting it worked. I let it go then. The same thing happened again within a day or two. Each time restarted the router seemed to solve the problem, however temporarily.
I have the SPI firewall enabled also I have application port forwarding set for HTML port 80 forwarding to say port 1234.
I have bought a WAG320 & ever since I've had it the ADSL line keeps dropping every few hours. The LAN network is fine & I have 7 computers connected to the router wirelessly. When I press the re-set button on the back of the router everything is fine for a few hours then it starts doing it again?
View 9 Replies View RelatedIs there any way to disable WPS feature on my WAG120?
View 1 Replies View RelatedJust bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies View RelatedHow do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies View RelatedI have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies View RelatedI've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies View Relatedproblems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies View Relatednormally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies View RelatedMy WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies View Related