Linksys Cable / DSL :: WAG120N Establish A Ssh Connection To Remote Server
Jun 15, 2011
I have WAG120N and I want to use ssh tunneling to browse the net.In windows, I have to use a software like putty or xShell to establish a ssh connection to remote server.It works perfectly and I don't have any problem with it.The problem occurs when I want to use this ssh account in linux.At first,connection established without any problem or error.After 2-3 minutes it seems ssh dies and no data transmitted through ssh tunnel.I tried this with Symphony ADSL modem(Wired only) and I have no problem with it.I want to know if there's any specific problem or configuration for WAG120N to solve this problem?I like this modem/router and I don't want to sell it and buy any other modem/ router.I have to mention that usually I use wired connections to WAG120N,but at some cases I need to use its wireless features.
View 4 Replies
ADVERTISEMENT
Sep 6, 2012
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies
View Related
Mar 22, 2011
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies
View Related
Jul 18, 2011
I have 2 Router (Cisco WAG120N) and (Micronet SP3364)I am connected to the Internet with MicronetUse Cisco Only ACCESS PointI am putting Cisco on a bridge and OnlyBut I am having problem ... Cisco is always disconnected, but I have internet on the wireless network through the Cisco.
View 2 Replies
View Related
Mar 23, 2012
I will just explain my setup:
I have a ADSL Huwavi modem by my ISP installed at my place.. Now the wireless from that device is very bad.. So I purchased WAG120N to setup a daisy-chain kind of setup in my other bedroom. I also put another D-link DIR-600 in between to give a connection to the first floor (via Ethernet cable).
So my huwavi is the ISP device, then a LAN from it goes to the dlink internet (WAN) port. then one cable from the d-link LAN port to the LAN1 of WAG120N and another upstairs.
Now all of this was working perfectly.. I put same SSIDs and Pwds on both ISP router and WAG120N and i was getting seamless net..
Now yesterday we removed the ISP modem to do some shifting.. Upon reconnecting, the ISP modem, Dlink work as before, but the WAG120N refuses to connect to the net.. it shows DSL down and doesn't access the www.
What I felt is that since i changed LAN ports on my ISP device and dlink, the static IP settings on the WAG120N should be changed.. i modified it, set to to point to the dlink for internet and huwavie for DHCP.. yet nothings happening..
I even connected the WAG120N directly to the Huwavie, yet it fails to connect to the net..
View 1 Replies
View Related
Nov 24, 2010
I don't know if this because buggy firmware (i updated to V1.00.16) or there something wrong with the device but if i set radio band to AUTO which enable wide-channel, my wireless connection become unstable when i ping to the modem, i got 200ms - timeout randomly
my family notebook that on other side of room connection also become more worst , ping to the modem (192.168.1.1) timeout so often
the connections seems better if i set radio band to standard - 20Mhz channel even though it seems WAG54G2 have more stable wireless connection (i replace it because the ethernet port dead) i also tried to change the channel, but the issue still persist, it seems the default is the most stable (channel 9 for wide, 11 for standard)
should i RMA the product as i just purchase last week? or it just because the bad firmware ?
View 9 Replies
View Related
Jun 1, 2011
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
View 1 Replies
View Related
Jul 6, 2012
Recently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
View 5 Replies
View Related
Aug 15, 2011
From time to time, when I wake up an specific station from sleep mode, the router loses its connection with Internet. It still has the line synced, but there is no Internet connection.I still can access the router through browser though. If I hit "connect" to establish a manual connection, it does not work. I have to switch the router off and on and wait for the whole process of syncing and connection, then I have Internet again.
I thought this could be something on that PC (old XP) sending some weird packet to router when I wake it up, but I tried with a newer PC (Win 7 64 bits) and the same problem persists. Also, this only happens when I wake up the PC. If it is off and I turn on, or if I restart, the problem does not happen.
The router (WAG120N) has an old firmware version (V1.00.12) because the latest available is buggy and had some problem with my ISP (limiting the bandwidth). However, I have this firmware for like 6 months and the problem only started 2 months ago.
View 4 Replies
View Related
Aug 28, 2012
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies
View Related
Jan 1, 2011
I have a problem with my wag120n and iphone or ipad or macbook.The connection works well for about 1-2 hours then stops.so with macbook i have to disable airport and connect to the network again with iPad or iPhone i have to turn-off and REturn-on the wifi.I have already changed the wireless channel but this didn't work form me.
View 5 Replies
View Related
Jul 17, 2012
i am trying to establish a VPN connection between two remote offices.In the home side I have Cisco 1811W and on the far side CiscoSRP541.
What is the best solution to build a site-to-site VPN between those two locations. I originally thought to configure a GRE tunnel on the routers, but faced some issues with that.
View 9 Replies
View Related
Jul 15, 2012
I have a sky router (Netgear DG834GT), which i have connected a secound router to which is a D link DIR-615 (with DD wrt firmware D4).I can get access to the sky router remotely without any issues even when changing the port number. its the Dlink router i cannot get access to remotely (within the network i can by typing in the dlink's ip address and works). Main router Sky router IP is 192.168.0.1 - Currently the port number is 8081.Secondary router Dlink IP is 192.168.0.2 (Static ip) - currently the port number is 8080.I have tried to configure the ports but it just dont want to open. Ive tried to open the ports on main netgear and tried all the option my dlink for port forwarding. i must be missing something fundametal here.
View 2 Replies
View Related
Jul 16, 2012
We have two sites, Site-A with a ASA 5520 (Remote Access IPSEC VPN server) at one end and a new ASA 5515-X at Site-B. Users at Site-B are unable to establish a VPN connection to Site-A via Cisco VPN client from behind the new ASA 5515-X. They see the following error:
"Secure VPN Connection terminated locally by the client.
Reason 412: The remote peer is no longer responding.
They are able to access the same from home or elsewhere so I believe there is nothing wrong with Site-A ASA vpn config which we have been using for a while now. The new 5515-X (version 8.6) has a very basic config with all outbound traffic allowed. I'm pasting the config below. Do I need to enable/allow anything for it to work?
CISCOASA# sh run: Saved:ASA Version 8.4(3)!hostname CISCOASAenable password xxxxxxxxxxxx encryptedpasswd xxxxxxxxxxxxxx encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address x.x.x.x 255.255.255.248!interface Ethernet0/1 nameif backup security-level 0 ip address
[Code]....
View 15 Replies
View Related
Aug 28, 2012
My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.
View 1 Replies
View Related
Jan 2, 2012
I have an issue with a Cisco 4900M switch with a WS-X4908-10G-RJ45 half card. The link connection between a 10Gbase-T server nic and the switch does not establish, i believe it is an auto negotiation problem. The link fluctuates constantly between connected and disconnected when set to auto negotiate. When the 10G half card port groups are configured for 1G connections it does the same. If i hard code the server nic to 1G the link remains up when the port group is at 1G. If i hard code the server nic to 10G the link stay down, i don't think the port speed and duplex can be hard coded on the switch end. I have tried updating the drivers on the server as well as diagnostic tests on the nic, which passed. The 4900M IOS code is version 15.0.2-SG2. If i plug a laptop into the 1G configured port the switch and the laptop negotiate at 1G. Also, i believe, if the 10G server nic is plugged into another 1G only switch the link auto negotiates to 1G as normal. The server nic is an INTEL Server Adapter AT 10G, which became end of life in 2009. I believe the half card came out in 2010.
View 5 Replies
View Related
Aug 24, 2012
Is there any way to disable WPS feature on my WAG120?
View 1 Replies
View Related
Mar 31, 2011
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies
View Related
Jul 20, 2011
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies
View Related
Apr 19, 2012
I have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies
View Related
Mar 27, 2011
I've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies
View Related
Jul 22, 2011
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies
View Related
May 14, 2012
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
View 1 Replies
View Related
Jan 31, 2012
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies
View Related
Jan 24, 2011
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies
View Related
Oct 24, 2010
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
View 6 Replies
View Related
Nov 22, 2011
I configured my router Linksys WAG120N as DMZ, but not forward port 80, only port 80.
View 1 Replies
View Related
Apr 18, 2010
I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
View 4 Replies
View Related
Apr 18, 2013
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies
View Related
Apr 4, 2012
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies
View Related
Oct 3, 2011
1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
View 1 Replies
View Related
Apr 24, 2013
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies
View Related
Aug 23, 2011
After the upgrade in v1.00.16 Annexe A, I've a problem ADSL sync with the WAG120N, the router don't need the sync, how to back the v1.00.12 Annexe A.
View 1 Replies
View Related
