Linksys Cable / DSL :: WAG120N / DIR 600 - Internet Connection Failure
Mar 23, 2012
I will just explain my setup:
I have a ADSL Huwavi modem by my ISP installed at my place.. Now the wireless from that device is very bad.. So I purchased WAG120N to setup a daisy-chain kind of setup in my other bedroom. I also put another D-link DIR-600 in between to give a connection to the first floor (via Ethernet cable).
So my huwavi is the ISP device, then a LAN from it goes to the dlink internet (WAN) port. then one cable from the d-link LAN port to the LAN1 of WAG120N and another upstairs.
Now all of this was working perfectly.. I put same SSIDs and Pwds on both ISP router and WAG120N and i was getting seamless net..
Now yesterday we removed the ISP modem to do some shifting.. Upon reconnecting, the ISP modem, Dlink work as before, but the WAG120N refuses to connect to the net.. it shows DSL down and doesn't access the www.
What I felt is that since i changed LAN ports on my ISP device and dlink, the static IP settings on the WAG120N should be changed.. i modified it, set to to point to the dlink for internet and huwavie for DHCP.. yet nothings happening..
I even connected the WAG120N directly to the Huwavie, yet it fails to connect to the net..
View 1 Replies
ADVERTISEMENT
Apr 29, 2011
I have been using it since approx 6months ago. Previously it was working well except for some major signal issues. However, 3 days ago it decided to go haywire. 1) It does not connect to the internet 2) It does not detect/connect to the computer when LAN cable is plugged in (does not load in 192.168.1.1) 3) I have tried resetting the router many times and even holding the reset button for 30 secs and switching off and switching on but to no avail. 4) I have had a linksys live chat with Johnel and he determined that it may be a possible hardware problem 5) Current Status of the Router: It makes no attempt to establish any connection/load whenever turned on, as seen when no lights are blinking when switched on. Upon switching on, Power Light becomes Red and Internet Light becomes Red and the middle Refresh Button become Red. 6) I have tried installing the driver for the router but there is no way I can install the driver because the computer does not detect that the router is connected What can I do about these? 1) Can I get a replacement of a different model? This router has been giving me problems since Day 1 2) I am seriously considering switching my service provider from M1 to Starhub. If that is the case, is there any way I can be replaced with a Cable Modem instead of ADSL Modem?
View 9 Replies
View Related
Aug 15, 2011
From time to time, when I wake up an specific station from sleep mode, the router loses its connection with Internet. It still has the line synced, but there is no Internet connection.I still can access the router through browser though. If I hit "connect" to establish a manual connection, it does not work. I have to switch the router off and on and wait for the whole process of syncing and connection, then I have Internet again.
I thought this could be something on that PC (old XP) sending some weird packet to router when I wake it up, but I tried with a newer PC (Win 7 64 bits) and the same problem persists. Also, this only happens when I wake up the PC. If it is off and I turn on, or if I restart, the problem does not happen.
The router (WAG120N) has an old firmware version (V1.00.12) because the latest available is buggy and had some problem with my ISP (limiting the bandwidth). However, I have this firmware for like 6 months and the problem only started 2 months ago.
View 4 Replies
View Related
Aug 28, 2012
Yesterday I bought the Linksys Wireless-N Home ADSL2+ Modem Router WAG120N (Annex-A version). I configured the modem/router and it was working very well. Today I was surfing the internet just fine and I left my computer for a few minutes, when I came back I noticed that there is no internet connection. The internet light on the modem was no longer on, and the DSL one was blinking. I turned off the device and then turned it back on but the issue was still present. I tried restoring the factory default settings and configuring the modem again but nothing seems to work (resetting the modem, turning off every device connected to it and restarting the modem/router). The DSL light keeps blinking, turns off for a couple seconds and then starts blinking again. The internet light only appears when I restart the modem and it flashes red just after turning the device on.
View 8 Replies
View Related
Mar 22, 2011
when choosing "Mixed" or "N-only" as Network Mode on the Basic Wireless Settings configuration page, the mode resets to "B/G-Mixed" or "G-only" respectively when saving. In other words, it is not possible to use the N network mode.
View 4 Replies
View Related
Jul 18, 2011
I have 2 Router (Cisco WAG120N) and (Micronet SP3364)I am connected to the Internet with MicronetUse Cisco Only ACCESS PointI am putting Cisco on a bridge and OnlyBut I am having problem ... Cisco is always disconnected, but I have internet on the wireless network through the Cisco.
View 2 Replies
View Related
Nov 24, 2010
I don't know if this because buggy firmware (i updated to V1.00.16) or there something wrong with the device but if i set radio band to AUTO which enable wide-channel, my wireless connection become unstable when i ping to the modem, i got 200ms - timeout randomly
my family notebook that on other side of room connection also become more worst , ping to the modem (192.168.1.1) timeout so often
the connections seems better if i set radio band to standard - 20Mhz channel even though it seems WAG54G2 have more stable wireless connection (i replace it because the ethernet port dead) i also tried to change the channel, but the issue still persist, it seems the default is the most stable (channel 9 for wide, 11 for standard)
should i RMA the product as i just purchase last week? or it just because the bad firmware ?
View 9 Replies
View Related
Jun 1, 2011
I have a 3G USB modem connected to my desktop and I would like to share the internet connection to other devices wirelessly using the WAG120n ADSL router. How do I set up the IP's manually on the router and my PC to do this? And which other setting do I need to set?
View 1 Replies
View Related
Jul 6, 2012
Recently, i bought a LinkSys WAG120N ANNEX-A to replace my old speedstrem4200. Well everything was fine, but after 2 days of it installed, it started to drop my ADSL connection.
Sometimes, it remain connected for 4-5 hours, then drop, or sometimes, it drop every 30min-1hour.I tried upgrading the firmware to 1.00.16, but no luck, it still drop the connection.I have 3 computer plugged to the router via cable(wired) plus 1 netbook(wireless) and 1 ipod (wireless).Sometimes, when 1 computer is turned off, it seem to make the ADSL connection drop when the LAN light turn off. I noticed everytime it drop the ADSL connection, in the logs, i get this:
Mon, 2010-11-08 22:24:57 - Terminating on signal 15. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_store. Mon, 2010-11-08 22:24:57 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:57 - Enter: tdb_update. Mon, 2010-11-08 22:24:57 - Couldn't increase MTU to 1500. Mon, 2010-11-08 22:24:57 - Couldn't increase MRU to 1500 Mon, 2010-11-08 22:24:57 - LCP down. Mon, 2010-11-08 22:24:58 - Modem hangup Mon, 2010-11-08 22:24:58 - Connection terminated. Mon, 2010-11-08 22:24:58 - Connect time 215.0 minutes. Mon, 2010-11-08 22:24:58 - Sent 50496235 bytes, received 212267122 bytes. Mon, 2010-11-08 22:24:58 - Enter: tdb_store. Mon, 2010-11-08 22:24:58 - tdb_store: calling tdb_update. Mon, 2010-11-08 22:24:58 - Enter: tdb_update. Mon, 2010-11-08 22:24:58 - Doing disconnect Mon, 2010-11-08 22:24:58 - Exit.
I tried changing the MTU settings in the router to 1492 (my ISP default) but didnt work.
Tried changing the MTU to 1492 on every computer and still got the same problem.For now im using the WAG120N in bridge mode, and still using my old speedstream4200 as ADSL modem.
View 5 Replies
View Related
Jun 15, 2011
I have WAG120N and I want to use ssh tunneling to browse the net.In windows, I have to use a software like putty or xShell to establish a ssh connection to remote server.It works perfectly and I don't have any problem with it.The problem occurs when I want to use this ssh account in linux.At first,connection established without any problem or error.After 2-3 minutes it seems ssh dies and no data transmitted through ssh tunnel.I tried this with Symphony ADSL modem(Wired only) and I have no problem with it.I want to know if there's any specific problem or configuration for WAG120N to solve this problem?I like this modem/router and I don't want to sell it and buy any other modem/ router.I have to mention that usually I use wired connections to WAG120N,but at some cases I need to use its wireless features.
View 4 Replies
View Related
Jan 1, 2011
I have a problem with my wag120n and iphone or ipad or macbook.The connection works well for about 1-2 hours then stops.so with macbook i have to disable airport and connect to the network again with iPad or iPhone i have to turn-off and REturn-on the wifi.I have already changed the wireless channel but this didn't work form me.
View 5 Replies
View Related
Oct 24, 2010
I have a WAG120N which runs speedtest.net at 0.1 Mbs. My old router used to get 6 Mbs.I have tried a firmware update & reset, reduced the MTU to 1300 but still no different.Windows Vista & 7 - two different computers, same speed...
View 6 Replies
View Related
Apr 18, 2010
I am using WAG120N, and it keeps disconnected from internet randomly, normally between 5-10 minutes. The thing is, when it is disconnected, the adsl lamp is still on, so I think that it is not the network problem. When internet lamp turns off , I try to turn off the device (or unplug the phone cable), then turn it on again (or re-plug the cable), and it will work for certain minutes, then gets disconnected again. I already upgraded the firmware to v 1.00.12.
View 4 Replies
View Related
Nov 29, 2012
I recently got a Linksys WAG120n wireless modem but I have a problem with its Wireless.whenever I want to connect to the wireless of the modem I have to reboot the modem. or I cannot connect to it or if I connect I do not have internet access the cable LAN interface of the modem is working is working properly.I used Mixed (b/g/n) as network mode and wpa2/psk as authentication mode with using preshared key.and the channel is 11. no matter if I enable MAC filtering for wireless or not it is just the same.my laptop is a HP G42 with a Ralink 3090 wireless card and I have installed the latest manufacturer driver of the wireless Card.but it is not working .even sometimes laptop cannot find the linksys modem until I reboot the modem.as I have found there is no newer firmwire on cisco site for this modem to upgrade.
View 1 Replies
View Related
Mar 18, 2013
I have a wag120n ADSL modem. When I turn on the modem, after about 30 min to 1 hour DSL LED light flashing and then internet LED light turn off, and disconnect from internet. And modem does not connecting to internet until I turn off and turn on again the modem. I check with other modem it is working fine and DSL line is not the problem. Also I installed the latest firmware and that not solved the problem.
View 1 Replies
View Related
Dec 12, 2011
Recently I shifted to ADSL2+ Internet broadband.So purchased "CISCO Linksys WAG120N" router as my firewall hardware( FortiGate60) had no any port to connect to ADSL.Now I'm accessing internet throug the above Linksys router and do not use the firewall as I don't know how to configure the firewall to get the internet access through firewall from the router.My earlier broadband service was directly connected to the firewall's WAN port as it was compatible.configure the firewall to access the internet from the router through the firewall.
View 2 Replies
View Related
Aug 10, 2012
I am using linksys cisco wag120n adsl2 modem router.When I start the router the internet speed seems great but after some time the speed drops miserably. When I again restart the router the speed seems great for few mins but again drops after sometime.It happens in both LAN and wireless mode.The firmware version of the router is 1.00.16
I was going through the problems posted by some other user but observed that cisco people are not heraing to them.Seems made a mistake by associating with cisco product.This is the worst router I have ever used.The wireless also gets disconnected abruptly.Next time I'll avoid cisco.Cisco is all about stone age products and zero customer care.
View 1 Replies
View Related
Nov 23, 2011
is it possible to moderate sharing bandwitch or/and traffic internet over wireless via WAG120N for some specific client? is there any configuration inside modem OS?without any external software such as Cyberoam or... that they need Always-On PC to work!
View 3 Replies
View Related
Dec 26, 2010
I have local WI-Fi network with 2 Macs, 2 PC's, iPhone, iPod and i Pad at home on Link sys WAG120N router. On i Pad when I try to connect to Internet I have to turn WiFi off and on. It works for a while but after waking i Pad from sleep I have to switch off and on again. It really drives me crazy. Sometimes (hardly ever) it happens on my iPhone 4 (same network setup as on i Pad). Other devices connect to Internet whenever I need.
View 9 Replies
View Related
Aug 7, 2012
Have problem with both of my wag120n routers. I setup remote access, from the intranet it works fine. But from internet instead of showing me the page it starts downloading it. Instead of home page trying to save ¨download¨, if i put a long link like xxx.com/setup.cgi?=etc then it tryes to save ¨setup.cgi¨. All fileas are empty, 7kbytes.
View 7 Replies
View Related
Aug 24, 2012
Is there any way to disable WPS feature on my WAG120?
View 1 Replies
View Related
Mar 31, 2011
Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok, Wireless is lit and DSL is also also lit. Rebooted a few times too.
View 1 Replies
View Related
Jul 20, 2011
How do I set up the WAG120N as a router only as I no longer want to use it as modem and router?I want to connect the WAG120N thru a cable to a modem that will make the internet connection and use the WAG120N as a wireless router only.
View 3 Replies
View Related
Apr 19, 2012
I have a WAG120N modem-router.What i want is to have my public IP on my pc.So... just 1 pc with 1 ip... but whatever i do... nothing works.
View 1 Replies
View Related
Mar 27, 2011
I've got a new WAG120N which seems to lock up about every 24 hours. All the lights are on except the wireless light goes out. Can't login to it and its quite hot.
View 3 Replies
View Related
Jul 22, 2011
problems when I wanted to connect my laptop to my WAG120Nrouter for the first time.First the wireless adapter on my windows xp gives me the error "unable to verify your identity"second when i passed the security verification by bypassing the security options on the connection properties of the adapter, windows tries to acquiring network address and continues it for hours. Seems Windows cannot get any ip address from the router.The router works fine with wired Ethernet devices and my iPhone when i connect it wirelessly.
View 1 Replies
View Related
May 14, 2012
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
View 1 Replies
View Related
Jan 31, 2012
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies
View Related
Jan 24, 2011
My WAG120N does not allow airprint from ipad/ipod to HP photosmart wireless printer. When i replace the linksys router with an old netgear one all works well and the ipad can find the printer and print. Enable the Linksys router and the printer is no longer found on the ipad. other forums suggest this relates to handling of the Bonjour protocol ... any resolution for this so i dont have to go back to legacy speed on my home wifi?
View 3 Replies
View Related
Nov 22, 2011
I configured my router Linksys WAG120N as DMZ, but not forward port 80, only port 80.
View 1 Replies
View Related
Apr 18, 2013
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies
View Related
Apr 4, 2012
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies
View Related
Oct 3, 2011
1) I dis abled the DHCP services on modem router as i was connecting it to a belkin router and after that i cannot accesss the setup of the WAG 120N.
2)If I acces the WAG120N by Lan the internet works fine but if i acces through wirless it does not.
3)Also when ever i connect the LAN cable from BELKIN router to WAG 120N the wirless services stop as well on the BElkin router and i cant figure it out why.
View 1 Replies
View Related
