I recently purchased a Slingbox PRO-HD and the iPad software to view HD on my iPad when I'm away from home. When I setup the Slingbox using their web-based configuration program, it reports that I do not have my network configured for the best performance for internet viewing, which is what I need for the iPad. I suspect that I don't have port forwarding for port 5001 correctly setup on my system. I can successfully connect to my Slingbox away from home on my iPad and my laptop, but the performance is indeed poor.
I have a cable modem and two E2000 routers. The first E2000 is connected to my cable modem in my home office and the second E2000 is in my home theater. I used Cisco Connect on separate PCs to setup the two routers. Here are the details:Cable modem:Scientific AtlantaModel DPX2203 SeriesPart number 4006351'Ethernet' connected to Router 1 'Internet' connection.
How to forward a single port to a different port to a specific computer for the WRV210 router?
I would like to forward port 10100 to port 25 to my mail server. There are times when our people are at a hotel and they block port 25 and I have done this in the past on a BEFSR11 and BEFSR41 router. There does not seem to be a Single Port Forwarding setup page and the Port Forwarding setup page only allows you to forward a range to a specific computer, it does not give you a different port you can assign an incoming port to.
I have the most current firmware revision, 18.104.22.168, and Hardware Version WRTR-221G_V01.
I currently have cable internet connected to one router (Linksys E2000 w/ firmware v1.0.03). That router is connected to another router, a Linksys E3200 w/ firmware v1.0.02. In order to properly forward ports through the E3200, I understand that I need to set up a static IP on that router.I've basically followed the steps outlined in this video, but when I enter all the IP addresses for Static IP settings, it won't allow me to access the router's setup page. I try entering the new IP that I've given it (which it tries to direct itself to automatically after I save the settings) and the connection times out. I am able to access the internet otherwise, however. From here I'm forced to do a factory reset on the router and start from square one.
So currently I'm having issues with changing my nat type to open for my ps3. I've tried to use DMZ and port forwarding to change the nat type, but sadly I couldn't get this to work. Most the guides on the forums are for xbox's which wouldn't work for a ps3. Any handy guide to change my nat type to open for my ps3?
At the E4200 there is a limit of (free to make) 15 Single port forwarding and 15 port range forwarding to fill in.I get as suggestion that I must give up a total range of ports where all the ports I use where in.But for security reasons I will not do that.
The Port 80 port fowarding stops functioning after a few hours and requires the router to be rebooted to start forwarding again. The firmeware is the latest 1.0.04 Build 7. I require it to operate reliably for many days without intervention. I assume that it is a port forwarding problem because I can access the IP on my network from within my network even when I can't access it from outside my network. I am using the correct IP addresses as it sometimes works OK. A characteristic is that when I can't access the page it loads as completely blank white with no error message.
I've been wanting to port forward this game called Minecraft for quite awhile now, but never got around to it, but now that I've wanted to let my friends that can't play with hamachi play with me. I wanted to port forward it so that they go into the game without using hamachi, or any other networking program. I've already tried once and whenever I ran my server, I would say "FAILED TO BIND TO PORT" or just ask me this "Is another running on that port?"
I did read the thread entitled ''WRT160N Can't save settings'', but I believe this might be different. My router is actually communicating with my computer (physically plugged in), since I can save all other settings EXCEPT the port-fowarding ones.I am trying to save settings for a gaming application in the Single Port Forwarding section of my router settings. After clicking both ''save settings'' and ''continue'', it simply returns to the Single Port Forwarding section, except everything is blank, as though nothing was saved.
Here are my specs:
WRT160Nv1 Firmware Version: v3.0.03
Here are the steps I have already undertaken:
1- Erase browser cache and cookies
2- Updated to latest firmware (v3.0.03), 10-second reset button, 20-second power cycle.
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
I cannot add or modify the informations in the Single Port Forwarding . I get a message saying: Invalid Character(s) found. All characters are good. I get the same message when only click on the "SAVA" button. I have the latest firware V22.214.171.124
Is there a way to forward a single port, while leaving the others alone? For instance I want to forward all https traffic on a public IP to an internal server on port 4443. At the same time traffic on all other ports for this IP needs to be forwarded on the original port. It looks like creating a Network Object will allow a single port to be forwarded, but what happens to the remaining traffic? I attempted to create Service Objects that I then assigned to NAT statements.
After a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
Im trying to open up some ports on my e3000 for the use of Teamspeak and my Teamspeak server. However when i get of the information filled into the single port forwarding under the Gaming & Applications tab, and click save settings. The page just refreshes, with none of the changes being saved.
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Linksys E1200 Router not saving Port Forwarding changes.I have tried:
-Restarting the Modem -Restarting the browser -Restarting the computer -Tried to Port Forward through both the Single and Ranged Port Forwarding
IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
I upgraded to a 6500 from a e4200. I use ports 81-84 on test web servers set to static Ip,s when I open the ports nothing can get through from the outside. I can hit the pages internally on those ports and IP's but not from my external ip to those ports. When I set my old router everything is fine.