I have one 3945 router with SM-ES3-16-P module with SL-ES3-16-IPS. I am not seeing any license for this module in CLI output of my router. How do I add license for this module and activate. do I need IP Service IOS for this module
View 1 RepliesI am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 1 Replies View RelatedI have a Ethernet module (SM-ES3G-16-P) installed in a 3945 router and noticed during first boot no licenses are active at all. I would assume at a mimimum ipbase would be active. With this module, does static routing work with just ipbase?
Example:
interface g0/1
no switchport
ip addr 192.168.254.2 255.255.255.0
[code]....
We have Cisco 3945 Router with SM-ES3-24P Switch Module. when we tried to configure routing in Router and Layer 3 ports on Switch module, the inter-communicaiton is not working?
how we can use routing in 3945 with SM-ES3-24P module?
We want to implement HSRP between two 3945 ISRs:
RouterModelIOSModuleR1Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-1.T.binNME-AIR-WLC12-K9
R2Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-4.M1.binNME-AIR-WLC25-K9
The issue that we are experimenting is that, although the module's interfaces are up and HSRP in correctly configured, the show standby summary displays that the Active router is local in both routers. We also have some GigabitEthernet in the routers and they are correctly running HSRP. Does the WLC Modules physically support HSRP?
if the Cisco 3945 router requires any license for it to run HSRP. Also advise which IOS runs HSRP on the 3845 router.
View 3 Replies View RelatedI've a 3945 with SM-ES3G-24-P module installed and tried to configure some routing but it doesn't work .
1. L3 interface on the switch modules (with ip address configured)
2. OPSF on the router with connected interface redistribute (which includes the switch module L3 interfaces)
I don't see any of the switch module L3 interfaces routes in the router, not even the connected interface.
SM
-----
int g0/1
no switchport
ip add 1.1.1.1 255.255.255.0
Router
---------
int g0/0
ip add 2.2.2.2 255.255.255.0
router ospf 1
redistribute connected
network 2.2.2.2 0.0.0.0 area 0
We just recently purchased a 3945 ISR G2 router and have a SRE-910 module (with two hard drives) configured in a Raid 1. We are running a stand-alone version of ESXi on the service module and I'm trying to figure out how to monitor the status of the Raid on the drives (along with other health issues). SNMP has revealed nothing so far and even opening a support case for which MIB's to use has proved fruitless. All the documents I find on monitoring the modules say to use LMS which is now Cisco Prime. I've downloaded the trial copy, put in the SNMP settings and scanned the router. I get device results and it shows that I have the SRE-910 module installed, but I get no other configuration / device informaiton from the module itself.
I tried to create a new Monitoring template using the NAM health as the base template (which I'm assuming this is the correct template). Unfortunately, when I actually try to deploy the template against the discovered router, I get an 'Unexpected end of list' error which makes me assume I'm still doing something wrong.
I try to connect a cisco blade switch 3020 to Nexus 2232 with etherchannel, but when I connect the second link a obtain flapping on vlans. [code] why the vlans are flapping ? it's something wrong on the config ? [code]
View 7 Replies View RelatedI have 4 cisco 2960 switches to which many users are connected. No vlans are the only default vlan 1 is there. Now I want to make ether channel on switch 1 whcih has 24 fast etherenet ports. Can I make port 1- 8 as one ether channel which are connected to users or i can only make ethere channel of ports that are connectd to other switchs. If I can, how the other switchs will comnicate with the switch ports bundalled in the ether channel in switch 1.
View 6 Replies View RelatedI'm trying to upgrade an asr1001 (r1) from asr1001-universal.03.02.00.S.151-1.S.bin to asr1001-universalk9.03.02.00.S.151-1.S.bin. i've put in the boot system flash asr1001-universalk9.03.02.00.S.151-1.S.bin command and reloaded but the box keeps loading first image the configuration register is 0x2102. i've tried the license module command to enable adv enterprise but it made no difference so i removed it again. my license is now;
License Package Information for Module:'asr1001'
Module name Image level Priority Configured Valid license
asr1001 adv enterprise 1 NO adv enterprise adv ip services 2 NO adv ip services ip base 3 NO ip base
I recieved my IPS module license for my ASA 5525 . I enetered the key via the ADSM and it prompted me to restart the firewall .. After that i cannot get into the firewall via the ASDM .
View 3 Replies View RelatedI'd like to establish a more robust border router/switch redundancy plan and would like to know if this seems like it would be reliable.I'm looking at using a couple of 3945 routers and 3750 switches in the configuration shown below.
The article found at [URL] outlines the config between a single switch and router but I am looking at doing this with dual routers and switches.
We are having problems with a two router 3945 in HSRP and a switch 2960.The two routers are connected to the switch 2960 through differentes ports. The problem is that we loose connection between the router and the switch.When we excute the command: show cdp neighbor at router, it shows nothing.If we try to make ping to the 2960 switch it is no reachable.If we make ping to the other router 3945 it is not reachable.All other function of the router are o.k.We are attaching the IOS of the routers and switch 2960 and a document in which make reference to a BUG in which mention about arp overwrite due arp attack which produce DoS.
View 2 Replies View RelatedI am using Cisco 4510 Switch with Default LAN Base image. Now I have purchased 10G Upgrade license. The part number for Upgrade license is WS-C4500-10G-LIC. I have received a CD from Cisco (named as 'Includes License and Warranty'). Any License upgradation is required for this license? Or this is only a paper License.
I could not find out any .lic file on the CD. Also there is no paper with PAK.
I used to have this situation where I need to replace faulty ASA5510 (this FW did not failover to standby FW) with the new one.
But the problem is the new ASA5510 came with Base License only not with Security Plus License which is needed to allow this brand new device to be configure failover.
how do I pull out Security Plus License from old FW and switch it to new FW (Base License) and activate to Security Plus License.
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies View RelatedDoes the Network Module "C3KX-NM-1G" and "C3KX-NM-10G" for Cisco Catalyst Switch 3750X Comes with a transciever like GLC-SX-MM or SFP-10G-SR or do I need to order in seperately.
View 1 Replies View RelatedI have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?
View 7 Replies View RelatedSuffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies View RelatedAny doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies View RelatedWe have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies View RelatedI'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies View Relatedi have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies View RelatedWe got a new Cisco 2911 router (CISCO2911/K9) with a switch module (SM ES2-16-P) on it. Everything works fine after the configuration except for the power. We got 4 WAP that we will connect to the switch module that needs power. So the switch module with POE doesn't give any power out.
[code]....
Recently on two switches, both being same cisco WS-C3750E-24PD, running with same IOS c3750e-universalk9-mz.122-58.SE2.bin got noticed that the license state of one switch is showing incorrectly as shown below [code] I will not be able to execute any changes/modifications on switch as of now.
View 9 Replies View Relatedhow to configure FWSM module in cisco core switch 6500
View 2 Replies View RelatedWe have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.
View 1 Replies View Related I have a problem with a newly bought ws-x4548-rj45v+ i've plugged in the module but when i do show modules all , it show as unsupport
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 2 Supervisor IV 1000BaseX (GBIC) WS-X4515 JAE1048GAXQ2 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB064806WN3 48 10/100/1000BaseT (RJ45) WS-X4448-GB-RJ45 JAB063005DB4 0 Unsupported module WS-X4548-RJ45V+ JAE1545056U
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 0007.0e64.f880 to 0007.0e64.f881 5.2 12.2(20r)EW1 12.2(46)SG Ok2 000b.5fa4.da20 to 000b.5fa4.da4f 1.0 Ok3 0009.e844.d760 to 0009.e844.d78f 1.0 Ok4 ccef.4815.9bf0 to ccef.4815.9c1f 2.0 Unsupport
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View RelatedI have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
Trying to find some documentation as to whether there are any other steps for inserting this new module in our N7K. We have 2 blades in already and 2 Sups in 5 & 6. I'm assuming its like the 6500s, where we just slide it in and the OS configures the global parms for it and the default VLAN.
View 2 Replies View RelatedWe having a VSS switch (9 slot chasis) with ios "s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI4", slot 7-9 are currently free. We wanted to install WS-X6708-10G-3C module on slot 7. Once we installed the module it didnt come, after waiting for 15-20min again we removed and inserted, but module didnt come up and we could see following logs on the console:
Jan 12 08:57:40.146: %ISSU-SW2_CFC2-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
*Jan 12 08:57:40.330: %ISSU-SW2_SPSTBY-3-ERP_AGENT_SEND_MSG: client/entity send failed; error code is timeout
Jan 12 08:57:40.146: %ISSU_ERROR-SW2_CFC2-3-START_NEGO_FAILED: ISSU NTI Client(2040): failed to start negotiation (ISSU_RC_CLIENT_ENTITY_DOES_NOT_EXIST_IN_PEER)
[code]....
Afer some time VSS switch didnt response to console commands and all the users in access switches were not able to reach the gateway (VSS). Then the problem disappeared once we rebooted both the switches in VSS.why the VSS switch become non-responsive?