Cisco Switching/Routing :: 1941W - Service Module Failed
Jul 25, 2012
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
View 3 Replies
ADVERTISEMENT
Apr 12, 2012
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
View 2 Replies
View Related
Mar 10, 2013
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies
View Related
Jun 17, 2012
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies
View Related
Jun 8, 2011
I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies
View Related
Dec 12, 2011
I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
View 4 Replies
View Related
Jun 9, 2012
On 2921, how do you quite service-module session and get back to the router?
View 3 Replies
View Related
Oct 18, 2012
[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
View 1 Replies
View Related
May 31, 2012
I have been trying to make a stack with two 2960S. They have the same IOS but they behave as they were not connected.One is in production and I am attaching a brand new one to it; in the one that is in production I get these 2 messages:
FlexStack Module SmartChip Authentication Failed.I tried switching the modules and the outcome is the same, so I think the modules are ok.What to you recommend, is there a way to bypass this authentication?
View 6 Replies
View Related
Dec 8, 2012
I have a Cisco catalyst 6513 with sup720-3bxl and WS-X6724-SFP modules , the switch was working fine until yesterday ,but after a maintenance the modue WS-X6724-SFP failed to bring online , the error code is (Module Failed SCP dnld) does it mean the module has hardware problem or i need to replace it ?
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ios version
s72033-adventerprisek9_wan-vz.122-33.SXH7.bin
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
show module
Mod Ports Card Type
Model
[code]....
View 3 Replies
View Related
Jan 2, 2013
Something strange is happening to my Cisco 1941W. Every time I reboot the router i loose the running configuration of the service-module (Access Point module). The weird thing is that the router's configuration remain the same. I made sure i save the configuration by issuing the wr command on the service module console but still happens. My router's current IOS version is 15.0(1)M1 and my AP's is 12.4(21a)JA1.
I also did another test by making sure the startup-configuration was identical to the running configuration and when I reload the router still happens.
View 7 Replies
View Related
Mar 23, 2013
I own a 1941w that is covered by a service contract and I'm entitled to download software for it. But unfortunately I don't see any option to download AP software for it. I need an upgrade for the internal AP to connect it to a virtual WLC.Apparently I need ap801-rcvk9w8-tar.152-2.JB.tar to get this done.I can find it under the 800w series, but I don't own a service contract for that so I can't download anything.
View 1 Replies
View Related
Dec 27, 2012
I'm currently trying to get up to speed on a 1941W ISR. I belive i have most of the configuration correct based on reading the documents on this site. However, i'm noticing that my lan to lan network performance is very slow. Peaking out about 3mbs. I was reading some documentation that suggested MGF (MultiGigabit Fabric) might resolve this problem.
I have a basic setup in my test environment trying to emulate a branch deployment. 1941W connected to a access switch (3400).
- I'm getting slow perfomance (thoughput) between the vlans 66,30,10. Will MGF fix this problem? How do i configure it?
Building configuration...
Current configuration : 7474 bytes
!
! Last configuration change at 09:26:04 PCTime Fri Dec 28 2012 by xxx
! NVRAM config last updated at 09:26:05 PCTime Fri Dec 28 2012 by xxx
[Code]......
View 4 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Jun 12, 2013
I've a Cisco 1941W router which is DHCP server for data-VLANs and uses ip-helper for voice-VLANs. [code] I don't know why I can't have IP from wireless voice VLAN whereas it is OK and wired voice VLAN and conf is the same!
View 4 Replies
View Related
Nov 15, 2011
This is the message that I am getting from my 1941w router. I have a isakmp tunnel built with a GRE tunnel going through it.
View 15 Replies
View Related
Mar 20, 2012
I have a number of devices in my house connecting without issues:
1.) PS3
2.) XBox 360
3.) HP CM1415FNW
4.) Sony Dash
5.) iPone 4g/4gs
6.) Asus EP121
7.) Six Laptops
8.) TV
9.) Denon A/V
My android cant even pickup the SSIDs, I stand beside and still nothing, the SSIDs are not hidden, Ive tried different encryptions, changed from AES to TKIP, tried different channels. I have two seperate SSIDs, one 2.4GHz with B/G/N and a 5.0 with A/N Available, neither SSID is getting picked up
View 4 Replies
View Related
Apr 20, 2013
open specific ports on 1941w Integrated Services Router.This specific router is a wireless VPN router that has a wired module and a wireless module and VPN so I'm getting 3 subnets on my network - 192.168.1.. for the wired connections, 10.100.1.... for wireless LAN connections and 10.100.2... for VPN remote connections.I know that by default all connected computers can access my Linux server data through telnet so the telnet port is open by default, the problem is that I have some other software licensing system on my Linux box that needs to be accessed through port 27000 and most of my users are using wireless connections and can't access that license because post 27000 is closed.what is the comand to open this post or any other port that I need to be open on the wired module, wireless module and VPN or at least poit me to somewhere where I can find all the commands that I can use for this router?
View 6 Replies
View Related
Mar 11, 2013
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies
View Related
Jan 1, 2013
can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies
View Related
Aug 26, 2011
What does the message: Failed to run service When computer first opens, the above message has to be deleted before I can get on internet.
View 1 Replies
View Related
Dec 5, 2011
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies
View Related
Jun 3, 2013
Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies
View Related
Mar 20, 2013
I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
View 2 Replies
View Related
May 18, 2012
My connection status icon has a big red x on it. I can't get on the internet. I tried the cmd stuff( ipconfig,netsh renewand release, and all the other jazz to do) my ip address starts with a 169 # I know that's not good. I go into my networks and I have no network. I go into my LAN ip4 and ip6and there are no addresses no were.I checked the LAN area status and it says not connected.
View 8 Replies
View Related
Mar 27, 2012
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies
View Related
Dec 27, 2011
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies
View Related
Sep 1, 2010
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies
View Related
Dec 2, 2012
My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
View 2 Replies
View Related
Feb 23, 2013
I've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows
Current OS: Windows 8 PRO
Model: ASUS K43SV
View 1 Replies
View Related
Jul 20, 2011
DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies
View Related
Nov 10, 2011
when I made the purchase for Linksys X3000. However, when I reached home and tried to use it. It auto reboot every 1 or 2 mins of usage. It's not just wireless affected but the whole thing rebooted. Reflash the fimware doesn't makes much different. Did a Standard 30-30-30 reset didn't solve any problem. Logged the case and informed linksys customer service that I'll go down to the retail shop for replacement. Case ID Given.On the 8th Nov, I went back to the retailer shop and proceed to get a replacement. The shop was fine, they allowed for one on one replacement. However problem persist. This time it got worse, when I tried to flash the firmware, it got stuck at 98% for half an hour. So I got it rebooted. Next, It can't boot up and the power status shown Red color.
I contacted the same customer service and inform them about the same issue with the replacement. Next I was given the address of the RMA Office at Funan L5-K3. Problem is, the address and location is wrong, the office became a Kawaii Koochi cosplay dessert shop.On the 10th Nov 2011, Checked the address in the net and some stated it's in Bishan and some stated it's in Funan. I called the Number given by the customer service and the line is dead. Called again, this time its Indian CSO and was told by the customer service that they're not operating after 7pm. But the problem is, it's only 5.30pm. Apparently they thought I was in US or Canada. So they transferred me to another customer service but nobody picked up the call. The fella just told me that hey, they not picking up so there's nothing he could do and that's it.I called a number started with 800-1204280, they told me that the office location is in Funan lvl 6 just beside the huge challenger store. I went down again at about 6.30pm and managed to locate the Service Center, I think it's third party as it cater for other product such as lenovo and other brand.This time the RMA center customer service told me that they doesn't carry any stock for replacement. I wasted so many trip just for one router. It's a very dissappointing service overall and this product is highly unreliable.
View 3 Replies
View Related
Nov 14, 2012
After I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.
View 7 Replies
View Related
