Cisco WAN :: 2811 / Getting Error Unsupported DIMM
Apr 7, 2011
I have a 2811 with 512 of memory installed (two by 256). The router has been sitting spare for sometime and I know there was once a memory problem with it long ago. It has two 256M Non ECC DIMMs installed and seems to work fine. I recently tried to install a 512M DIMM ECC and all I get is 'Unsupported DIMM" error - same if I remove the other 256M DIMM leaving just the 512M. I have tried three different DIMMs - and all have the same error message. One of the DIMMs is 'cisco supported' and based on what I can find in the web - seems to be the correct spec. I have also tried non ECC 512 DIMM and 'unsupported DIMM" error message is still coming up. If I did not know better, I would say that there was something that needed changing in the config to allow 512M DIMMs to be installed.
View 6 Replies
ADVERTISEMENT
Jul 17, 2012
how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies
View Related
Dec 26, 2011
I have a large quantity of ASA5520's and ASA5540's that need to be quickly assessed and RTV'd (if need be) if they are found to be upgraded ASA5510's.
My concern is because of this recent release-note by Cisco: [URL]
Is there a way to check the amount of DIMM slots on a unit through console or do I have to physically check each and every one?
View 2 Replies
View Related
Mar 27, 2012
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies
View Related
Nov 26, 2012
I have a 2811 Router that keeps cycling through reboots. About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below. It then does a dump and reboots. This cycle just continually occurs.
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)
View 2 Replies
View Related
Aug 23, 2009
Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)
When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT file back to teh Compact Flash.
Then it runs for a few weeks and the same problem happened.
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem.
View 6 Replies
View Related
Oct 15, 2012
I am trying to use a Dell FTRJ8519P1BNL SFP fiber module in a Cisco Catalyst 3560 and have already run these commands: no errdisable detect cause gbic-invalid service unsupported-transceiver.But I STILL am getting these errors even after shut/no shut on the port.
View 19 Replies
View Related
May 11, 2012
We have a site with 4 access point, where two are are showing up in CNA, version 5.7(6), as "Unsupported device" the two others are working fine.
The unsupported devices are:
AIR-AP1131G-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The supported devices are:
AIR-AP1131AG-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
getting CNA recognize these access points?
View 7 Replies
View Related
Jul 3, 2011
I have CNA 5.5 and have upgraded our 4506 with sup. v4 to cat4500-entservicesk9-mz.150-2.SG.bin (latest version). CNA shows the 4506 as an usupported device.
View 4 Replies
View Related
Jun 8, 2010
I am looking to uplink an HP Blade Chassis to a Cisco 3750-X with SFP+ for 10Gig on each end.I would like to use Direct Attached SFP+ cables if possible.I already know that the HP Virtual Connect module will not accept a Cisco Direct Attached cable at the current firmware.Cisco Nexus 5000 has a feature allowing connectivity with the HP Direct Attached cable using "unsupported" mode.
View 3 Replies
View Related
May 14, 2012
I seem to have managed to set a 2960 to 230400 baud in the boot loader. Is there anyway to reset the variables in the boot loader? Maybe a set of pins to short? I can't access the console port reguardless of what I set the rate too. I've tried both the USB console cable and a USB to serial. Is there anything I can do short of an RMA?
View 4 Replies
View Related
Apr 19, 2006
We are running IOS12.4(5a) on a 2821 and have "ip inspect esmtp" enabled. We noticed that every day several emails end up in the postmaster account with the following message:
"A mail message was not sent due to a protocol error.
500 Firewall Error
The message that caused this notification was:"
On closer inspection the router logfiles show:
Apr 20 08:54:19 loghost 830747: 810587: Apr 20 08:54:19.441 BST: %FW-3-SMTP_UNSUPPORTED_PARAMETER: Unsupported SMTP parameter (Data Size (> 20000000)) from initiator (172.16.1.6:3537)
But the emails in questions are just a few kB. So what is going wrong. This is especially disturbing because the users don't get a notification that the email has not been delivered.
View 2 Replies
View Related
Jan 19, 2010
Receiving syslog message :%SIP-3-UNSUPPORTED: Unsupported ptime value. But we have no SIP-related commands in our config. We reloaded router Friday eve 1/15 but two more %SIP-3-UNSUPPORTED: Unsupported ptime value messages re-appeared on 1/18. The router in question is a 3745 running c3745-a3jk9s-mz.123-14.t7.bin. This router does have one interface facing an ISP.
View 4 Replies
View Related
Dec 4, 2011
We ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies
View Related
Nov 3, 2011
I recently ordered and received Cisco Catalyst 3560-CG Series 8-port PoE switches (ws-C3560CG-8PC-S). In running the Cisco Network Assistant (Version 5.6(3)) they show up as an unsupported device. The documentation for this product indicates that you can use CNA to configure this switch. Is there a download or patch available to correct this problem?
View 8 Replies
View Related
Jan 17, 2012
When i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies
View Related
Jul 17, 2012
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
View 3 Replies
View Related
Sep 10, 2011
I'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies
View Related
Mar 12, 2013
The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
View 5 Replies
View Related
May 1, 2012
I'm trying to open certain websites but the browser gives me this message: "Network Error (tcp_error) A communication error occurred: "Operation timed out" The Web Server may be down, too busy, or experiencing other problems preventing it from responding to requests. You may wish to try again at a later time.
View 8 Replies
View Related
Apr 20, 2011
i'm currently studying at a college which has a website with a student intranet that is available to log in from any computer. So far it has been working well and I can log in on my home laptop and upload documents and look at presentations etc. Today for no reason when I try and log in I get the message Error Code 500: Internal Server Error and the webpage does no appear.I have had no problems previously and this has only happened today and yesterday, I went down to the college and accessed the website fine from the computers in the library but still no joy from my home computer.
View 1 Replies
View Related
Sep 19, 2012
My setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies
View Related
May 27, 2013
I need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
View 3 Replies
View Related
Feb 29, 2012
I want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
View 3 Replies
View Related
Aug 23, 2012
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies
View Related
Mar 19, 2012
i have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies
View Related
Nov 2, 2011
I have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies
View Related
Nov 8, 2011
I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
View 5 Replies
View Related
Feb 14, 2013
I have a 2811 that I can remotely VPN to using Cisco VPN client however I cannot see the internal admin network (10.35.5.0).
Current configuration : 4845 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
View 2 Replies
View Related
Sep 23, 2012
I have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
View 2 Replies
View Related
Apr 20, 2013
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
View 5 Replies
View Related
Mar 22, 2012
I have a Cisco 2811 with an additional HWIC-4ESW card. [code] I need to NAT anything heading out of the WAN port. [code] I can ping anything connected to my other private networks from my 10.0.24.0 network but nothing on the Internet. [code]
View 3 Replies
View Related
Jan 3, 2012
I just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies
View Related
