Receiving syslog message :%SIP-3-UNSUPPORTED: Unsupported ptime value. But we have no SIP-related commands in our config. We reloaded router Friday eve 1/15 but two more %SIP-3-UNSUPPORTED: Unsupported ptime value messages re-appeared on 1/18. The router in question is a 3745 running c3745-a3jk9s-mz.123-14.t7.bin. This router does have one interface facing an ISP.
View 4 RepliesWe ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies View RelatedWhen i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies View RelatedI am having two small issues....First on my 3745 i get the following message:
*Mar 2 12:13:13.615: IP-EIGRP(Default-IP-Routing-Table:1): Neighbor 192.168.3.1 not on common subnet for FastEthernet0/1
*Mar 2 12:13:25.811: IP-EIGRP(Default-IP-Routing-Table:1): Neighbor 192.168.2.1 not on common subnet for FastEthernet0/1
Second problem is that I have my internet connection going to the 3640 on FE0/0 and it works just fine....I want to change over and have the 3745 be the internet router, but when I configure it, I get no connection.
3745 -
Current configuration : 1624 bytes
!
version 12.4
service timestamps debug datetime msec
LD version 0x10
GIO ASIC version 0x127
[Code]...
I have a cisco 3745 router ,It has been working OK till this morning when it failed to boot this is the error that i get:
%ERR-1-GT64120 (PCI-0): Fatal error, CPU out of range error
GT=0x24000000, cause=0x0900E083, mask=0x0ED01F00, real_cause=0x08000000
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
bus_err_high=0x00000000, bus_err_low=0x083259C0, addr_decode_err=0x00000470
r0 = FFFFFFFF r1 = FFFFFFFF r2 = 0 r3 = 658A0000 r4 = 0
r5 = 1 r6 = 0 r7 = 0 r8 = 0 r9 = 4ECAB4A0
r10 = 0 r11 = 200 r12 = 0 r13 = 668BDF84 r14 = 0
[code]....
System returned to ROM by error - a System Error, PC 0x607DD5C0 at 11:06:37 ARG Fri Jun 15 2012 System image file is "flash:c3745-adventerprisek9_ivs-mz.124-15.T5.bin" Possible RAM fault?? not performed any modification.
am using GNS3, and have the 16port switching module. I have created a PC instance and connecting to f/0/0 which is a layer 3 port, I can connect via layer 3 IPs. I then reconfigured and connected the PC instance via a layer 2 port f2/0 which is part of the 16port switch module. All 16 ports are by default in vlan 1. I assigned an IP of 10.1.9.1/24 to the VLAN and gave the PC 10.1.9.2/24. I cannot ping and I cannot even ping 10.1.9.1, the VLAN 1 IP. [code]
View 5 Replies View RelatedI need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
View 5 Replies View RelatedI am almost new to the networking field, hence I might have lacking some basic knowledge. I like to know the impact if the ground of any router get disconnect. WIll the router stops work? We have two peripheral router in my organization, both are connect with the MPLS cloud through the MUX. One router (3745) have ground connection, where as the other (3845) don't. Recently the 3745 router start generating CRC error on the WAN interface. Once we remove the patch cord connecting with the MUX for loop test and reconnect later, the interface did not come back again. FInaly someone advice me to check the ground connection. I found it was loose. Once I fix it properly and reboot the router the interface become up. The person told me that some cisco router send the reference signal through the ground to the MUX connecting with it, if the MUX and router failed to exchange the reference signal the router will not work, is this true ?
View 2 Replies View RelatedI have two routers I am trying to connect via the WIC-2T port. I can ping from router to router, but not from my PC (192.168.2.122) to the 3745 (10.0.1.3)..
3640:
Current configuration : 1846 bytes
!
version 12.2
[Code].....
I've came across a very odd topology to deal with where everything is connected to everything, without proper utilization of VLANs.
- I've an L3 SW and a 3745 RTR at core
- Both are carrying same subnet to an L2 distribution switch that connects server farm within the same subnet (i.e. 1.1.3.x subnet)
- The L2 switch works as a passive switch, hence another network say, 1.1.2.x has been plugged into it as well.
- This L2 switch extends to other switches without configuration of any VLANs or STP and distributes 1.1.3.x network.
Periodically and unexpectedly, the router starts hanging and utilization goes beyond 80%, and there's nothing at all that is observed in "sh proc cpu" to be eating router resources. Its quite difficult to observe the pattern, as its random.
I am trying to use a Dell FTRJ8519P1BNL SFP fiber module in a Cisco Catalyst 3560 and have already run these commands: no errdisable detect cause gbic-invalid service unsupported-transceiver.But I STILL am getting these errors even after shut/no shut on the port.
View 19 Replies View RelatedWe have a site with 4 access point, where two are are showing up in CNA, version 5.7(6), as "Unsupported device" the two others are working fine.
The unsupported devices are:
AIR-AP1131G-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The supported devices are:
AIR-AP1131AG-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
getting CNA recognize these access points?
I have CNA 5.5 and have upgraded our 4506 with sup. v4 to cat4500-entservicesk9-mz.150-2.SG.bin (latest version). CNA shows the 4506 as an usupported device.
View 4 Replies View RelatedI am looking to uplink an HP Blade Chassis to a Cisco 3750-X with SFP+ for 10Gig on each end.I would like to use Direct Attached SFP+ cables if possible.I already know that the HP Virtual Connect module will not accept a Cisco Direct Attached cable at the current firmware.Cisco Nexus 5000 has a feature allowing connectivity with the HP Direct Attached cable using "unsupported" mode.
View 3 Replies View RelatedI seem to have managed to set a 2960 to 230400 baud in the boot loader. Is there anyway to reset the variables in the boot loader? Maybe a set of pins to short? I can't access the console port reguardless of what I set the rate too. I've tried both the USB console cable and a USB to serial. Is there anything I can do short of an RMA?
View 4 Replies View RelatedI have a 2811 with 512 of memory installed (two by 256). The router has been sitting spare for sometime and I know there was once a memory problem with it long ago. It has two 256M Non ECC DIMMs installed and seems to work fine. I recently tried to install a 512M DIMM ECC and all I get is 'Unsupported DIMM" error - same if I remove the other 256M DIMM leaving just the 512M. I have tried three different DIMMs - and all have the same error message. One of the DIMMs is 'cisco supported' and based on what I can find in the web - seems to be the correct spec. I have also tried non ECC 512 DIMM and 'unsupported DIMM" error message is still coming up. If I did not know better, I would say that there was something that needed changing in the config to allow 512M DIMMs to be installed.
View 6 Replies View RelatedWe are running IOS12.4(5a) on a 2821 and have "ip inspect esmtp" enabled. We noticed that every day several emails end up in the postmaster account with the following message:
"A mail message was not sent due to a protocol error.
500 Firewall Error
The message that caused this notification was:"
On closer inspection the router logfiles show:
Apr 20 08:54:19 loghost 830747: 810587: Apr 20 08:54:19.441 BST: %FW-3-SMTP_UNSUPPORTED_PARAMETER: Unsupported SMTP parameter (Data Size (> 20000000)) from initiator (172.16.1.6:3537)
But the emails in questions are just a few kB. So what is going wrong. This is especially disturbing because the users don't get a notification that the email has not been delivered.
I recently ordered and received Cisco Catalyst 3560-CG Series 8-port PoE switches (ws-C3560CG-8PC-S). In running the Cisco Network Assistant (Version 5.6(3)) they show up as an unsupported device. The documentation for this product indicates that you can use CNA to configure this switch. Is there a download or patch available to correct this problem?
View 8 Replies View RelatedI'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
View 3 Replies View RelatedI'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies View RelatedI need to connect site to MPLS provider and run Cisco GETVPN.Problem:I have been browsing Cisco Feature Navigator Tool and to my surprise when I enter "platform:3745" I can't find an image compatible with GET VPN. there is no workaround (image) I can run GET VPN on 3745? I need IP routing (BGP, OSPF) as well.
View 1 Replies View Relatedwe've got a pair of old 3745's that are getting upgraded to new 2911's, and I'm trying to run IOS 15.2 on the new routers to get them most current before going into test and production use.The routers are doing BGP, IPv4, and HSRP, and I'm trying to put one in at a time as to not have to big bang everything at once. I'm putting the one that matters least in first, and basically using the same config as the old one, which was running IOS 11.
I was using "no ip mroute-cache" on ethernet interfaces, and it says that command is deprecated and I should use the MFIB commands instead. Darn if I know what that means, I believe it was set up so the ethernet interfaces had IP multicast fast switching disabled, which was set up by our vendor 10 years ago so I'm not sure if it matters. It would seem logical to me this would have an impact on HSRP and speed of failover. Does this matter, and if so how in the world do I do this with IOS 15.2?The second one is the use of "no fair-queue" on our serial connection for a T1. This command isn't there either, and I'm not sure if I even need to bother on this. It was set up on the old router on a T1 Frame Relay circuit.
There is no special requirements, just need new hardware with some reserve availability. As for now it's 3745 EOL and I assume to use 3945.
View 4 Replies View Relatedi just configured GRE over IPSEC on my Cisco 3745 router with VPN module installed. As soon i hit 25Mbps traffic, my CPU is touching 80%.
What maximum Traffic 3745 with GRE over IPSEC it can support?
Also show process CPU sorted dont show any evidence of which process eating it up.
sh processes cpu sorted
CPU utilization for five seconds: 75%/75%; one minute: 77%; five minutes: 78%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
I have to replace the 3745 which is our edge router (running (C3745-ADVIPSERVICESK9-M), Version 12.4(23), RELEASE SOFTWARE (fc1)) with (I think) a 3900 (drawing from memory, I haven't actually seen the device yet).In an ideal world, I SHOULD be able to just set term length to "0", do a show run, copy that off to a text file, and then paste it into the new one...
View 19 Replies View Relatedhow many NM-32A or NM-16A module can be installed on 3745 and 3640 routers?
View 1 Replies View RelatedOne of my clients has an older 3745 running IOS 12.3 and we are looking at replacing it with a new 3945 that runs IOS 15.0. This router is also configured with CME. Is it possible to migrate the current 12.3 config to load on the new 15.0 IOS? This will be my first encounter with 15.0 so I don't know what I am up against at this time. I am just hoping I don't have to retype all the ephone config, dial-peers, etc
View 2 Replies View RelatedOur 3745 router goes into Rommon mode . I am trying to upload the ios using x modem & tftpdnld , but it giving error " monitor: command 'copy not found" for x modem & " monitor: command"tftpdnld" not found" for tftpdnld.
View 3 Replies View Relatedi have Cisco 7200 VXR in which OC3 circuit is terminated. Module installed in VXR is PA-POS-2OC3 Now i have to move this connection to 3745 Router.
What i need to know which card is required to connect OC3 in cisco 3745, as per online search this module NM-1A-OC3SMI will work, but i am confused with term ATM OC3 module, so is this the right card to connect same OC3 circit on 3745?
I intend to deploy a voice+data network using some old 3745 and 2811. The network in effect has six 3745 in a hybrid topology at different locations and each having three WIC-2T, one WIC-4T, three NMHDV-2E1. That's pretty much juicing out the maximum from these routers These will serve as my core routers and for access I will be using my 2811s with more VWICs and lesser WIC-2T to give voice and data to subscribers. The 2811s will have links to multiple 3745s. The NMHDV-2E1 will serve for the voice needs at the 3745 locations. All the WAN links will be E1. All my telephones will be on analog voice using traditional EPABX with CEPT/ PRI E1 cards for connecting to the routers. And for data, ethernet ports.Two of the routers will have E1 links to the PSTN and Internet which has to be extended to all my folks. Now, for the tricky part, all my network modules are refurbished stuff from ebay and all the ports will have links on them. I intend to use OSPF with only the backbone area.
View 7 Replies View RelatedI have a Cisco 3745 Router with 1 Subrate T3/E3 port card installed on it. We want to add another T3/E3 card,
Q1- Can i add another card in this model? Q2- Can we multilink bundle up two T3/E3 cards? (current we have a single DS3 P2P connection between two office, so want to increase the bandwidth)
We have a 3745 LNS router, currently there are less number of users connected.when a user dials request authenticated and one virtual-access interface is formed in LNS router.Now the user is disconnected the vpn and connected to VPN again in this case, whether the user is connected to the same virtual-access interface which was assigned before disconnecting or different virtual-access interface is created.
View 0 Replies View Relatedtrying to establish a connection on an ibm 3745 controller via two IBM 5822 modems to a cisco 2600 router using sdlc encapsulation secondary bridging data from the serial port to the E/Net port to run the 3270 client ???
View 19 Replies View Related