I am trying to use a Dell FTRJ8519P1BNL SFP fiber module in a Cisco Catalyst 3560 and have already run these commands: no errdisable detect cause gbic-invalid service unsupported-transceiver.But I STILL am getting these errors even after shut/no shut on the port.
View 19 RepliesWe have a site with 4 access point, where two are are showing up in CNA, version 5.7(6), as "Unsupported device" the two others are working fine.
The unsupported devices are:
AIR-AP1131G-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The supported devices are:
AIR-AP1131AG-E-K9
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
getting CNA recognize these access points?
I have CNA 5.5 and have upgraded our 4506 with sup. v4 to cat4500-entservicesk9-mz.150-2.SG.bin (latest version). CNA shows the 4506 as an usupported device.
View 4 Replies View RelatedI am looking to uplink an HP Blade Chassis to a Cisco 3750-X with SFP+ for 10Gig on each end.I would like to use Direct Attached SFP+ cables if possible.I already know that the HP Virtual Connect module will not accept a Cisco Direct Attached cable at the current firmware.Cisco Nexus 5000 has a feature allowing connectivity with the HP Direct Attached cable using "unsupported" mode.
View 3 Replies View RelatedI seem to have managed to set a 2960 to 230400 baud in the boot loader. Is there anyway to reset the variables in the boot loader? Maybe a set of pins to short? I can't access the console port reguardless of what I set the rate too. I've tried both the USB console cable and a USB to serial. Is there anything I can do short of an RMA?
View 4 Replies View RelatedI have a 2811 with 512 of memory installed (two by 256). The router has been sitting spare for sometime and I know there was once a memory problem with it long ago. It has two 256M Non ECC DIMMs installed and seems to work fine. I recently tried to install a 512M DIMM ECC and all I get is 'Unsupported DIMM" error - same if I remove the other 256M DIMM leaving just the 512M. I have tried three different DIMMs - and all have the same error message. One of the DIMMs is 'cisco supported' and based on what I can find in the web - seems to be the correct spec. I have also tried non ECC 512 DIMM and 'unsupported DIMM" error message is still coming up. If I did not know better, I would say that there was something that needed changing in the config to allow 512M DIMMs to be installed.
View 6 Replies View RelatedWe are running IOS12.4(5a) on a 2821 and have "ip inspect esmtp" enabled. We noticed that every day several emails end up in the postmaster account with the following message:
"A mail message was not sent due to a protocol error.
500 Firewall Error
The message that caused this notification was:"
On closer inspection the router logfiles show:
Apr 20 08:54:19 loghost 830747: 810587: Apr 20 08:54:19.441 BST: %FW-3-SMTP_UNSUPPORTED_PARAMETER: Unsupported SMTP parameter (Data Size (> 20000000)) from initiator (172.16.1.6:3537)
But the emails in questions are just a few kB. So what is going wrong. This is especially disturbing because the users don't get a notification that the email has not been delivered.
Receiving syslog message :%SIP-3-UNSUPPORTED: Unsupported ptime value. But we have no SIP-related commands in our config. We reloaded router Friday eve 1/15 but two more %SIP-3-UNSUPPORTED: Unsupported ptime value messages re-appeared on 1/18. The router in question is a 3745 running c3745-a3jk9s-mz.123-14.t7.bin. This router does have one interface facing an ISP.
View 4 Replies View RelatedWe ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies View RelatedI recently ordered and received Cisco Catalyst 3560-CG Series 8-port PoE switches (ws-C3560CG-8PC-S). In running the Cisco Network Assistant (Version 5.6(3)) they show up as an unsupported device. The documentation for this product indicates that you can use CNA to configure this switch. Is there a download or patch available to correct this problem?
View 8 Replies View RelatedWhen i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies View RelatedI'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots. I am not aware if this spare had been used in production before. [code]
View 3 Replies View RelatedI'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies View RelatedXP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu
View 1 Replies View RelatedASUS Notebook G60Vx Series
Windows 7 Home Premium 64-bit
Intel(R) WiFi Link 5100 AGN
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
Today, while surfing the web my internet connection on my PC just randomly shuts off. I go check on my laptop and its normal. My WiFi says that I am connected to an Unidentified network with no internet access. So i got frustrated and checked all the forums and nothing seemed to work. So i restored my computer to factory settings and I still got this problem. Does this mean my Wifi Card is bad? Is it a virus? I can see other networks fine but i just cant connect to mine!
View 8 Replies View RelatedI need to know if I'm right about this. I have a customer that wants me to set up a dynamic-to-static IPsec tunnel between an 1811 router (dynamic) and an ASA with a static address.The catch is that the 1811 sits behind an ISPs cable modem where it picks up a private 192.168.x.x address.
Is there any other way to make this work where the router with the dynamic IP is sitting behind a box that's doing PAT translations?
I've recently been tasked with providing access to several internal servers to a remote site via one of our ASAs. In order to keep things simple, I have begun by creating a single static NAT rule for one of the servers. The Site-to-Site VPN connection profile was then created and testing has begun. Unfortunately it looks as though the NAT rule isn't working. As I monitor the tunnel, I still see our internal number being broadcasted and not the mapped address, which prevents the tunnel from being established. The remote site has verified that this is what they are seeing too.
Appliance:
ASA 5510
ASA 8.4(2)
ASDM 6.4(5)
Address Legend:
(Note: The following addresses are not actual addresses.)
[Code]...
I have been trying to get my FTP server working for months with no joy. It works when I connect to it internally but not from outside. If I do a port scan, I can see that port 21 is open. I tried it with disabled firewalls and also checked with ISP that nothing is being blocked. I have attached the config file. I used several differnet FTP servers such as CoreFTP, Wing FTP etc.
View 13 Replies View Relatedwhy the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.
View 13 Replies View RelatedI am have unabled the cisco SDM on my pc, and able to get the http for my router 1841:I have done below configuraiton in my R1841[code] why I am not able to get the above commands, and does my SDM not work due to this or anything else need to be done?
View 4 Replies View Relatedmy ASA config does not work? My config is attached in a txt file.
I tried to forward port 25 and 110 from the outside to the inside server, but I can't connect...
I've got a new 891 to replace an old 837 and I'm struggling to get the dynamic nat pool working.I've successfully configured the dialer etc for PPPoE and when I set up a static NAT translation between my PC and an external address then I can ping hosts on the internet e.g. ping 8.8.8.8 successfully. But when I remove the static translation and try and use the dynamic NAT pool then no NAT translations take place, and show ip nat translations only shows the other static entries.The relevant bits of the config are below and I've also attached a full (cleaned) config.
ip nat pool TestPool 81.2.123.226 81.2.123.226 netmask 255.255.255.248
ip nat inside source list 15 pool TestPool overload
! Can only access internet when static route is defined for my PC
! If I remove this line then it doesn't use the dymnamic pool TestPool
ip nat inside source static 172.16.0.11 81.2.123.226
[code]....
SSH is not working in Cisco 7206 VXR Router. I have configure
Hostname
Ip Domain name
Crypto key generate RSA
IN Line VTY 0 4
transport input preferred SHH
transport input telnet SHH
But stll it is not working. I am getting invalid crc recieved in packet.
Current IOS running is 12.3 (19) Enterprise 3des
i have a 876 Router, connected to the Internet and a VPN. From inside i would like to pass all traffic destinied to 192.168.0.0 255.255.255.0 to the VirtualPPP IF and al the other to the Internet (vlan2) I have created this rule, but after applying ist works only for about 30 to 60 seconds. after that only the Internet reachable. Everytime i do a clear ip nat trans * both Interfaces will work für 30 to 60 secs again...
This is the relevant part of the cfg
ip nat inside source route-map Di1 interface Virtual-PPP1 overload
ip nat inside source route-map VLAN1 interface Vlan2 overload
!
access-list 1 remark CCP_ACL Category=2
[Code].....
We have an ASA running 8.2.2 (adsm 6.2.5). VPN connections are working well.But it's not possible to use a SIP client (phone or software) through an SSL tunnel.So today I've tried to look in detail on this problem. I installed an ubuntu system,openconnect and ekiga as softphone. In our network everything is working without any error. I used an external DSL connection to test everything over the VPN tunnel.I can ping the SIP server and I can access the https frontend of the the SIP Server.The client "seem's" to connect as well. I can call the ekiga client, it's ringing and i can speak and hear everything (most times).Dialing from the ekiga client ALWAYS fails. On the ASA there is no policy allowing or denying those connections. How can I trace it on the ASA ?
View 2 Replies View RelatedI have ASA 5505 with outside interface IP 206.206.206.5 I configured the SSL vpn on this but still i am getting page can not be displaed when opening https://206.206.206.5 from broadband.
Below is the related configuration in ASA. What needs to be done in order to able to connect SSL vpn.
group-policy GroupPolicy1 internalgroup-policy GroupPolicy1 attributesvpn-tunnel-protocol IPSec l2tp-ipsecwebvpn functions url-entry file-access file-entry file-browsing
tunnel-group DefaultWEBVPNGroup general-attributesdefault-group-policy GroupPolicy1tunnel-group DefaultWEBVPNGroup webvpn-attributesnbns-server 10.10.10.11 timeout 2 retry 2
policy-map type inspect http Http_inspect_policyparameters protocol-violation action drop-connectionclass BlockDomainClass resetpolicy-map global-policyclass global-class inspect dns inspect esmtp inspect ftp inspect netbios inspect rsh inspect rtsp inspect snmp inspect sqlnet inspect tftp inspect xdmcp inspect icmppolicy-map inside-policyclass HTTPTrafic inspect http Http_inspect_policy!service-policy global-policy global
webvpnenable outsideurl-list nuk001 "abc002" cifs://10.10.10.1 1
we have installed a new appliance of LMS 4.2.2 in our VmWare environment. The platform is running licensed to work with 1300 devices. We have approximately 500 devices in DCR, most of them are small switches ranging from Catalyst 2950 to Catalyst 3750, and also a bunch of Nexus 5548 switches.CiscoView is not working for any of them, we get an error message which we cannot interpret. We have updated to the newest possible device packages, but all to no avail.
View 2 Replies View RelatedI get a lot of information via RME or SNMP but not the RAM Information.
View 1 Replies View RelatedI have configured my Cisco 881 and it is quite stable but now I am working on some minor details.
I have several Public WAN IP addresses which are NATing to internal web server. When I go to the WAN IP at port 80 from the Internet, the NAT works fine and it maps perfectly to the internal Web server. However, when I try the same same WAN IP from the LAN which contains the web server, the Router blocks the traffic and I get nothing back.
I have verified that I can get to the Inernet from the LAN but it seems that I cannot go bfrom the LAN to the Internet and back into the LAN via NAT.
I have ASA running version 8.2.5 and using snmp v3 as below;
snmp-server group Authentication&Encryption v3 priv
snmp-server user SNMP_TEST Authentication&Encryption v3 encrypted auth md5 cisco123 priv aes 128 password123
snmp-server host IN 10.10.10.110 version 3 SNMP_TEST
LMS device credential is as per above SNMPv3 config.Can't get this to work. Digging aroung but no avail. I also try this on ASA 9.1 but same result.
I got a question about ACS 5.3 and WLC We have now the ACS 5.3 running for MAB (good working) and TACAS for device AAA.But now our WLC’s will not work.I have created already a special “custom attribute” => role1 / mandatory / ALL Already changed to the combinations Role1=ALL / Role1=All / Role1=all / role1=ALL / role1=All / role1=all But still not working. I get a wrong response.
I followed the guideline in attach, PDF file.
Debug dump from WLC
ACS 5.2 / ACS 5.3
-------------------
*tplusTransportThread: Sep 28 15:07:59.222: auth_cont get_pass reply: pkt_length=24
*tplusTransportThread: Sep 28 15:07:59.222: processTplusAuthResponse: Continue auth transaction
*tplusTransportThread: Sep 28 15:07:59.388: tplus response: type=1 seq_no=4 session_id=b1fddbfc length=6 encrypted=0
[code]....
what ios for 827-4v from 12.4 can i use for IPSEC+ddns?i tested some from 12.4 but normally working only 12.3(26)GD, but i want ddns feature? some from 12.4 is working with tracebacks, other is not loading - with error (loadprog: error - program section linked to illegal address)
View 4 Replies View Related