Cisco Switching/Routing :: 3745 / %ERR-1-GT64120 (PCI-0) / Fatal Error

Nov 3, 2011

I have a cisco 3745 router ,It has been working OK till this morning when it failed to boot this is the error that i get:
 
%ERR-1-GT64120 (PCI-0): Fatal error, CPU out of range error
GT=0x24000000, cause=0x0900E083, mask=0x0ED01F00, real_cause=0x08000000
  --------------------------------------------------------------------
   Possible software fault. Upon reccurence, please collect
   crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
  bus_err_high=0x00000000, bus_err_low=0x083259C0, addr_decode_err=0x00000470
r0  = FFFFFFFF r1  = FFFFFFFF r2  = 0        r3  = 658A0000 r4  = 0       
r5  = 1        r6  = 0        r7  = 0        r8  = 0        r9  = 4ECAB4A0
r10 = 0        r11 = 200      r12 = 0        r13 = 668BDF84 r14 = 0       

[code]....
 
System returned to ROM by error - a System Error, PC 0x607DD5C0 at 11:06:37 ARG Fri Jun 15 2012 System image file is "flash:c3745-adventerprisek9_ivs-mz.124-15.T5.bin" Possible RAM fault??  not performed any modification.

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Module N7K-M148GS-11 Removed By Fatal Error

Sep 2, 2012

I had a problem during setup of a new module N7K-M148GS-11 into a Nexus 7000 10-Slot chassis.The module was powered-dn and removed by platform with the following message: [code]

Do I need to upgrade nx-os? There is a workaround?

View 3 Replies View Related

Cisco Switches :: Getting Fatal Error On SG300?

Oct 8, 2012

We have several SG300 Series Switches (8, 20, 28 and 52-Port Versions) running. All Switches do reboot from time to time: Some after a week or so, others several times a day and then run again happily. In the log I see:
 
%SYSLOG-F-OSFATAL:
FATAL ERROR: tExcTask: ABORT DATA exception 
***** FATAL ERROR ***** 
SW Version: 1.2.7.76
Version Date: 19-Jul-2012 Version 
Time: 17:54:43

[code]....
 
This happens with FW Version 1.2.7.76 as well as under Version 1.1.1.8.I do not know if this is related to FUGU, but it usually happens, when I try to open a connection with FUGU to some other host in the network?

View 10 Replies View Related

Cisco WAN :: 2811 Router Keeps Cycling Through Reboots / Fatal Error

Nov 26, 2012

I have a 2811 Router that keeps cycling through reboots.  About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below.  It then does a dump and reboots.  This cycle just continually occurs.
 
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)

View 2 Replies View Related

Cisco Switches :: SG300 28P Crashed Two Times / Fatal Error

Jul 2, 2012

my switch crashed two times. below details about it.
 
03-Jul-2012 17:29:44 :%SYSLOG-F-OSFATAL:
FATAL ERROR: GOAH: ABORT DATA exception
***** FATAL ERROR *****
SW Version  :  1.2.5.70Version Date:  11-Jun-2012Version Time:  17:35:31
Instruction            0x150348Exception vector       0x10Program state register 0x600000130x0015014c
***** END OF FATAL ERROR *****
 
02-Jul-2012 16:11:39 :%SYSLOG-F-OSFATAL:
FATAL ERROR: GOAH: ABORT DATA exception
***** FATAL ERROR *****
SW Version  :  1.2.5.70Version Date:  11-Jun-2012Version Time:  17:35:31
Instruction            0x150348Exception vector       0x10Program state register 0x600000130x0015014c
***** END OF FATAL ERROR *****

View 8 Replies View Related

Cisco WAN :: 6509 / System Detected CRC Error Rate On Port ASIC Data Bus Exceed Fatal Threshold

Dec 7, 2010

Recently I faced 1 issue in MLS 6509.MLS  had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?

View 1 Replies View Related

Cisco Switching/Routing :: EIGRP And Internet With 3745

Feb 28, 2012

I am having two small issues....First on my 3745 i get the following message:
 
*Mar  2 12:13:13.615: IP-EIGRP(Default-IP-Routing-Table:1): Neighbor 192.168.3.1 not on common subnet for FastEthernet0/1
 
*Mar  2 12:13:25.811: IP-EIGRP(Default-IP-Routing-Table:1): Neighbor 192.168.2.1 not on common subnet for FastEthernet0/1
 
Second problem is that I have my internet connection going to the 3640 on FE0/0 and it works just fine....I want to change over and have the 3745 be the internet router, but when I configure it, I get no connection.
 
3745 -
Current configuration : 1624 bytes
!
version 12.4
service timestamps debug datetime msec
LD version 0x10
GIO ASIC version 0x127
[Code]...

View 6 Replies View Related

Cisco Switching/Routing :: 3745 Unsupported Ptime Value

Jan 19, 2010

Receiving syslog message :%SIP-3-UNSUPPORTED: Unsupported ptime value.  But we have no SIP-related commands in our config. We reloaded router Friday eve 1/15 but two more %SIP-3-UNSUPPORTED: Unsupported ptime value messages re-appeared on 1/18. The router in question is a 3745 running c3745-a3jk9s-mz.123-14.t7.bin. This router does have one interface facing an ISP.

View 4 Replies View Related

Cisco Switching/Routing :: GNS3 3745 No Switch Connectivity

Jul 18, 2012

am using GNS3, and have the 16port switching module. I have created a PC instance and connecting to f/0/0 which is a layer 3 port, I can connect via layer 3 IPs. I then reconfigured and connected the PC instance via a layer 2 port f2/0 which is part of the 16port switch module. All 16 ports are by default in vlan 1. I assigned an IP of 10.1.9.1/24 to the VLAN and gave the PC 10.1.9.2/24. I cannot ping and I cannot even ping 10.1.9.1, the VLAN 1 IP. [code]

View 5 Replies View Related

Cisco Switching/Routing :: Port Forward To HTTP Server 3745

Apr 18, 2012

I need getting access to my http server.  I have a host name that I configured to point to my IPS IP address.  Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]

View 5 Replies View Related

Cisco Switching/Routing :: 3745 Router Failed To Exchange The Reference Signal

Mar 17, 2013

I am almost new to the networking field, hence I might have lacking some basic knowledge. I like to know the impact if the ground of any router get disconnect. WIll the router stops work?  We have two peripheral router in my organization, both are connect with the MPLS cloud through the MUX. One router (3745) have ground connection, where as the other (3845) don't. Recently the 3745 router start generating CRC error on the WAN interface. Once we remove the patch cord connecting with the MUX for loop test and reconnect later, the interface did not come back again. FInaly someone advice me to check the ground connection. I found it was loose. Once I fix it properly and reboot the router the interface become up. The person told me that some cisco router send the reference signal through the ground to the MUX connecting with it, if the MUX and router failed to exchange the reference signal the router will not work, is this true ? 

View 2 Replies View Related

Cisco Switching/Routing :: Input Error And CRC Error On Router 1841?

Mar 12, 2013

The router 1841 is connected directly to the layer switch. the network diagram is below:
 
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
 
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
 
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)

[Code]......

View 5 Replies View Related

Cisco WAN :: Routing With 3640 And 3745 Via WIC-2T

Feb 8, 2012

I have two routers I am trying to connect via the WIC-2T port. I can ping from router to router, but not from my PC (192.168.2.122) to the 3745 (10.0.1.3)..

3640:
Current configuration : 1846 bytes
!
version 12.2

[Code].....

View 15 Replies View Related

Cisco WAN :: Routing Loop Due To High Utilization Of Router 3745

Dec 31, 2012

I've came across a very odd topology to deal with where everything is connected to everything, without proper utilization of VLANs.
 
- I've an L3 SW and a 3745 RTR at core
- Both are carrying same subnet to an L2 distribution switch that connects server farm within the same subnet (i.e. 1.1.3.x subnet)
- The L2 switch works as a passive switch, hence another network say, 1.1.2.x has been plugged into it as well.
- This L2 switch extends to other switches without configuration of any VLANs or STP and distributes 1.1.3.x network.
 
Periodically and unexpectedly, the router starts hanging and utilization goes beyond 80%, and there's nothing at all that is observed in "sh proc cpu" to be eating router resources. Its quite difficult to observe the pattern, as its random.

View 5 Replies View Related

Cisco Switching/Routing :: L3 Reboots And Gives Error

Dec 11, 2011

Almost every sunday L3 switch reboot and give following error message.

View 2 Replies View Related

Cisco Switching/Routing :: POE Error On 4500?

Nov 16, 2009

I'm seeing the following error on a 4500 running 12.2(46)SG
 
C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Module 5 inline power exceeds threshold: status changed to 'Pwr Over'
 
All the ports on module 5 have "power inline never" applied, in fact the whole switch has POE disabled.
 
I've attached a txt file with the show power detail output.

View 2 Replies View Related

Linksys Wireless Router :: Fatal Security Flaw In WRT54GS?

Feb 2, 2012

Firmware is 1.52.0.  Model is WRT54GS.I'm configured with WPA2-PSK/AES.  Broadcasting my SSID.  No MAC access filtering.HTTPS access only to the config pages.  Custom (not default) password.  Remote management disabled.
 
Summary:The router simply "forgot" its assigned SSID and reverted to broadcasting as "linksys".It also ceased encrypting its broadcast.I was able to log in and change it back.  It retained many of the OTHER settings I had previously configured.
 
Details:Two days ago, I noticed my client (laptop) could no longer see the usual SSID that I connect to on my home network.However, there was a new SSID in the area, named "linksys", broadcasting UNSECURED.Coincidentally, this new "linksys" access point had the exact same signal strength that my usual access point typically had.So, I connected to it, you know, just to see.I was only able to access the config pages at my custom IP address (not at x.y.0.1), prefixed with the "https://" scheme identifier.And it didn't prompt for a password.  Hopefully because it recognized the cookie my browser still carried from the last time I logged in to it.  But maybe because it had temporarily dropped ALL of its security measures...It was definitely my router.  Just, stripped of its usual encryption/authentication and its usual SSID.So, I switched the SSID back to what it usually is.And I turned the WPA2-PSK/AES encryption back on.The router "remembered" my WPA2 passphrase, which it displayed to me as plaintext when I pulled down the "security mode" dropdown menu and selected "WPA2 Personal".After re-configuring, it works as well as ever.Is this a known security flaw in the WRT45GS?  Because....it seems like a fatal one, as far as network security is concerned.Is it limited to one firmware release? 

View 9 Replies View Related

Cisco Switching/Routing :: Having Minor Error For WS-X45-SUP6-E?

Feb 15, 2012

We are facing issue of having minor error for SUP module details below,SUP: WS-X45-SUP6-E  see the minor error coming  while troubleshooting this SUP 6-E error as below,
 
module 3: SerialNo :

Overall diagnostic result: MINOR ERROR#
 
Test results: (. = Pass, F = Fail, U = Untested)

1) supervisor-bootup ---------------> U
2) linecard-online-diag ------------> F

View 5 Replies View Related

Cisco Switching/Routing :: Getting Error In 4948 Switch

Mar 13, 2013

My cisco 4948 switch is generating the below error,how do i troubleshoot this error.

*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client

View 3 Replies View Related

Cisco Switching/Routing :: CF Error On 3825 Router

Jan 22, 2013

After formatting the CF, the router is able to see the flash without a problem. I copied files to the flash - still able to see the contents okay. The problem ia that if i restart the router with the new flash, i get this error:
 
Jan 22 17:44:12.454 MSK: %SYS-5-CONFIG_I: Configured from console by bt_admin on
vty0 (10.10.10.44)
Jan 22 17:45:41.847 MSK: %SYS-5-RELOAD: Reload requested  by bt_admin on vty0 (1
0.10.10.44). Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]

[code].....

View 1 Replies View Related

Cisco Switching/Routing :: WS-X6724-SFP - Getting Minor Error

Sep 20, 2012

The line card WS-X6724-SFP inserted in slot 2 is getting MINOR ERROR. I could also see  TestTransceiverIntegrity: on port no 2/11 has failed.
 
Is this a h/w issue?
 
==================================================================================================
 
S/w model : WS-C6509-E
 
IOS : s72033-adventerprisek9_wan-mz.122-33.SXI3.bin
 
==================================================================================================
 
    1) TestTransceiverIntegrity:
 
 
   Port  1  2  3  4  5  6  7  8  9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
   ----------------------------------------------------------------------------
         .  .  .  .  .  .  .  .  .  .  F  .  .  .  .  .  .  .  .  .  .  .  U  .

View 2 Replies View Related

Cisco Switching/Routing :: 3750X Duplicate IP Error

Apr 9, 2012

I have just moved to the 3750X switch and have connected it to a 6509E. From the beginning I was having OSPF encryption errors, followed by flood warnings, LSA issue's, duplicate IP's which is baffling me.

There are no IP's which match on either switch however the 3750X was continually power recycling causing the interfaces drop continually.Even after disconnecting from the 6509 the 3750X continue to behave in the same manner. Could there be some issue with this switch?

View 6 Replies View Related

Cisco Switching/Routing :: Getting Error Logs In 6509?

Feb 3, 2012

%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080

[code]....

View 1 Replies View Related

Cisco Switching/Routing :: 3560C Amber LED But No Error

Mar 22, 2013

I have a PS3 connected to a Gig port on my 3560. When I boot-up the PS3 I have to wait around 30 seconds for it to get DHCP.
I noticed the orange LED would stay on and go green after 30 seconds. I assumed I would have an error-state but I do not, the port show connected with no errors even though it's orange. I have no connectivity from the ps3 until the light goes green and then all is well. The port is access and I have manually configured duplex and speed.
 
Switch>show version
Cisco IOS Software, C3560C Software (C3560c405ex-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)

[Code].....

View 5 Replies View Related

Cisco Switching/Routing :: 4507 FAN Sensor Error

May 13, 2013

I have 4507 switch and I got the error of fan sensor which is mention below [code] What the meaning of FAN Sensor both are Bad/off ?

View 4 Replies View Related

Cisco Switching/Routing :: Message Error With C3750-I5-M

Jan 2, 2008

I have this system: IOS (tm) C3750 Software (C3750-I5-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1
 
An error appear in console (many times in one minute):
 
Jan  3 16:25:37: %LINK-3-BADMACREG: Interface StackPort1, non-existent MACADDR registry for link 0
-Process= "<interrupt level>", ipl= 4
-Traceback= 20A364 187F04 58D6FC 58B950 2D7CE0 2E00C8 2E2BEC 2E2F24 2B0BF8
 
What is the problem? What is the solution?

View 2 Replies View Related

Cisco Switching/Routing :: WLC 5508 - Error From Same Subnet

Jul 16, 2012

Getting a lot of the following errors on our 5508 form the same subnet: 10.20.0.1 255.255.248.0 . I tried researching and not getting much.
 
broffu_SocketReceive: Jul 17 10:11:10.068: %DATAPLANE-3-DP_MSG: broffu_fp_dapi_cmd.c:2891 FP0.09:(7089389)[cmdAddIpv4:2921]failed to find ipv4 10.20.6.58
[code]....

View 2 Replies View Related

Cisco Switching/Routing :: Error Log On 5500 Series?

Feb 3, 2012

:  %DATACORRUPTION-1-DATAINCONSISTENCY: unterminated string in buffer of  length 129, counted: 129 -Traceback= 4027CB2C 402B1E88 4052884C 40528A48  40528D08 40529188 40529358 403247E8 403247D4

Cisco Internetwork Operating System Software
IOS (tm) C5RSM Software (C5RSM-ISV-M), Version 12.2(46), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Thu 26-Apr-07 19:41 by pwade
Image text-base: 0x40010948, data-base: 0x410F41D0

[code]....

View 6 Replies View Related

Cisco Switching/Routing :: 3560 Goes To Error-disable

Jun 25, 2012

I have port on cisco 3560 goes to error-disable,what is the cause of this issue,pls be noted this interface has BPDU Guard enable

View 3 Replies View Related

Cisco Switching/Routing :: Error Message On CAT4507

May 8, 2011

I've taken 2 4507's fresh out of the box running CAT4500E-ENTSERVICESK9-MZ.122-53.SG2.BIN which was upgraded from CAT4500E-IPBASEK9-MZ.122-53.SG2.BIN
 
I'm getting constant %C4K_S2W-4-WRITECALENDARERR:  Calendar write operation Failed errors on the console.  I was also getting them on the original IOS version.
 
Anything I've seen say's to ignore them but their very frequent filling up the logs.
 
There's very little return on google and no bugs to report on Cisco?

View 8 Replies View Related

Cisco Switching/Routing :: 6509 - Cannot Find Reference To Error

Mar 5, 2010

This is a 6509 with Sup-2/MSFC2.  Can't find any reference to this error on the cisco web site.

View 2 Replies View Related

Cisco Switching/Routing :: Giving Out Discard Error On 3750E

Apr 4, 2011

We're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].

According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin

View 1 Replies View Related

Cisco Switching/Routing :: 4507 Getting Error While Configuring A Switch

Nov 8, 2011

I have a 4507 cisco switch loaded with two sup-modules.. [code]

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved