Cisco Switches :: Getting Fatal Error On SG300?

Oct 8, 2012

We have several SG300 Series Switches (8, 20, 28 and 52-Port Versions) running. All Switches do reboot from time to time: Some after a week or so, others several times a day and then run again happily. In the log I see:
 
%SYSLOG-F-OSFATAL:
FATAL ERROR: tExcTask: ABORT DATA exception 
***** FATAL ERROR ***** 
SW Version: 1.2.7.76
Version Date: 19-Jul-2012 Version 
Time: 17:54:43

[code]....
 
This happens with FW Version 1.2.7.76 as well as under Version 1.1.1.8.I do not know if this is related to FUGU, but it usually happens, when I try to open a connection with FUGU to some other host in the network?

View 10 Replies


ADVERTISEMENT

Cisco Switches :: SG300 28P Crashed Two Times / Fatal Error

Jul 2, 2012

my switch crashed two times. below details about it.
 
03-Jul-2012 17:29:44 :%SYSLOG-F-OSFATAL:
FATAL ERROR: GOAH: ABORT DATA exception
***** FATAL ERROR *****
SW Version  :  1.2.5.70Version Date:  11-Jun-2012Version Time:  17:35:31
Instruction            0x150348Exception vector       0x10Program state register 0x600000130x0015014c
***** END OF FATAL ERROR *****
 
02-Jul-2012 16:11:39 :%SYSLOG-F-OSFATAL:
FATAL ERROR: GOAH: ABORT DATA exception
***** FATAL ERROR *****
SW Version  :  1.2.5.70Version Date:  11-Jun-2012Version Time:  17:35:31
Instruction            0x150348Exception vector       0x10Program state register 0x600000130x0015014c
***** END OF FATAL ERROR *****

View 8 Replies View Related

Cisco Switches :: Error Configuring DHCP Server On SG300?

Apr 5, 2013

Firmware 1.3 introduced a DHCP server.
 
It seems that I can add a pool for any subnet except the 192.168.1.1/24. I have successfully added a pool for 192.168.0.1/24, 172.16.16.1/24, etc. But when I use the same commands to add a 192.168.1.1/24 pool, I get:
 
sw(config)#ip dhcp pool network Device sw(config-dhcp)#address low 192.168.1.20 high 192.168.1.250 255.255.255.0 Illegal IP addresses range or subnet configuration Trying to configure a network pool on default IP interface
 
VLAN 1 IP was changed from default 192.168.1.254 to a static of 192.168.0.1.

View 2 Replies View Related

Cisco Switching/Routing :: 3745 / %ERR-1-GT64120 (PCI-0) / Fatal Error

Nov 3, 2011

I have a cisco 3745 router ,It has been working OK till this morning when it failed to boot this is the error that i get:
 
%ERR-1-GT64120 (PCI-0): Fatal error, CPU out of range error
GT=0x24000000, cause=0x0900E083, mask=0x0ED01F00, real_cause=0x08000000
  --------------------------------------------------------------------
   Possible software fault. Upon reccurence, please collect
   crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
  bus_err_high=0x00000000, bus_err_low=0x083259C0, addr_decode_err=0x00000470
r0  = FFFFFFFF r1  = FFFFFFFF r2  = 0        r3  = 658A0000 r4  = 0       
r5  = 1        r6  = 0        r7  = 0        r8  = 0        r9  = 4ECAB4A0
r10 = 0        r11 = 200      r12 = 0        r13 = 668BDF84 r14 = 0       

[code]....
 
System returned to ROM by error - a System Error, PC 0x607DD5C0 at 11:06:37 ARG Fri Jun 15 2012 System image file is "flash:c3745-adventerprisek9_ivs-mz.124-15.T5.bin" Possible RAM fault??  not performed any modification.

View 1 Replies View Related

Cisco WAN :: 2811 Router Keeps Cycling Through Reboots / Fatal Error

Nov 26, 2012

I have a 2811 Router that keeps cycling through reboots.  About 30 seconds into a boot, it shows the ALIGN-1-FATAL error(s) shown below.  It then does a dump and reboots.  This cycle just continually occurs.
 
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80 (code)

View 2 Replies View Related

Cisco Switching/Routing :: Module N7K-M148GS-11 Removed By Fatal Error

Sep 2, 2012

I had a problem during setup of a new module N7K-M148GS-11 into a Nexus 7000 10-Slot chassis.The module was powered-dn and removed by platform with the following message: [code]

Do I need to upgrade nx-os? There is a workaround?

View 3 Replies View Related

Cisco WAN :: 6509 / System Detected CRC Error Rate On Port ASIC Data Bus Exceed Fatal Threshold

Dec 7, 2010

Recently I faced 1 issue in MLS 6509.MLS  had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?

View 1 Replies View Related

Cisco Switches :: SG300-28 GUI Different Than Online SG300-48 Simulator

Aug 29, 2011

These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
 
Below is the blog I started for InterVlan issue [URL]
 
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
 
This is what I see on our switch.
 
Our switch version
switchd64684#show version                                                                                                                                              
SW version    1.1.0.73 ( date  19-Jun-2011 time  18:10:49 )
Boot version    1.0.0.4 ( date  08-Apr-2010 time  16:37:57 )
HW version    V01

View 1 Replies View Related

Cisco Switches :: SG300-28P And SG300-52 Web Managing - Fans

May 26, 2011

1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?

2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?

View 2 Replies View Related

Cisco Switches :: SG300-28 Uplink To Another SG300-28?

Feb 8, 2012

Can I connect a single Cat5e cable between two SG300-28 and link them?  If so what must I configure?

View 1 Replies View Related

Cisco Switches :: Difference Between SG300-28P And SG300-52

Jul 25, 2012

I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?

View 2 Replies View Related

Cisco Switches :: Replacing 3COM 4500 Switches With SG300-52?

Nov 21, 2011

I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
 
3COM Setup
#
interface GigabitEthernet1/0/1

[Code].....

View 2 Replies View Related

Cisco Switches :: SG300 Switches Have Poor Performance In Layer 3?

Jan 1, 2013

We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
 
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each.  Switch was connected to HQ Network as untagged VLAN 101.  I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great.  Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then  Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
 
I then  Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.

View 10 Replies View Related

Cisco Switches :: SG300 Switches Can Be Used With Microsoft NLB In Multicast Mode

Dec 18, 2011

does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?

View 2 Replies View Related

Cisco Switches :: VLAN Management Via SNMP On SG300-10 Switches

Aug 7, 2011

Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.

View 8 Replies View Related

Cisco Switches :: Multiple VLANS And SG300-28P Switches Setup?

Aug 20, 2012

I'm going to have several SG300-28P switches to setup.  I'll need to create multiple vlans for data, voice, and wireless traffic.  I have the following questions in setting up this configuration:
 
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice 
 
1) For managing the switches via IP, will LAN1 be the default management network?  Should I create a seperate VLAN for managing the switches?
 
2) For uplinking the switches together, I plan to trunk a port to connect the switches together.  What's the configuration on the trunk port to forward all vlans from one switch to another?
 
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC.  The phone supports tagging for the PC and the VoIP traffic.  For example on port 10, would VLAN 100 and 300 be set to tagged?

View 3 Replies View Related

Cisco Switches :: SG300-52 Multiple Lags Between Switches?

Jan 19, 2012

I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?

View 1 Replies View Related

Cisco Switches :: How To Configure Two Links Between Switches SG300

Apr 22, 2012

I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?

View 2 Replies View Related

Cisco Switches :: VTP And STP On SG300-28 Switch

May 9, 2011

I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.

View 2 Replies View Related

Cisco Switches :: Set Up LAG Between SG300-20 And SRW224G4P

Jul 19, 2012

On my SG300 I set up LAG for the last two ports.
 
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
 
I was thinking maybe doing firmware upgrades to both switches?

View 3 Replies View Related

Cisco Switches :: How To Assign SG300-10 To VTP

Jan 29, 2012

I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?

View 2 Replies View Related

Cisco Switches :: Does SG300-10 Support RIP

Jun 20, 2012

In the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?

View 6 Replies View Related

Cisco Switches :: SG300-10MP Keeps Going Down?

Jan 27, 2013

We purchased a SG300-52 last week to replace a 5yr old Dlink which has worked perfectly. 1 day after the SG300 went it it started crashing with this fatal error problem so I reverted the firmware back from 1.2.7.76 (latest) to 1.1.2.0 but I still get the problems.  It crashes when I have it on my lan with users connected or if I just have the switch on my desk with just my laptop connected, so it cant be a load issue or a network topology issue.  I already have a Cisco SGE2010 on my network without problems.

View 7 Replies View Related

Cisco Switches :: ACL Binding On SG300 28P

Mar 15, 2011

I have a question about ACL and binding. I have a SG300 28P and a couple of other linksys switches and Access points that are connected to it via trunks. The cisco SG300 28P  is running in layer3 mode and i have created a couple of vlans and one of them is a guest vlan. Now to my question, i create an ACL and an ACE that vill funktion so that guest vlan only can connect to the internet and not the rest of the internal network. And then i must bound the ACL to an interface port or lag, what i can see it is not possible to bind it to an vlan? so if i have a port on some of the other switches that is member of the guest vlan, vill the ACL on the SG 300 stop guest vlan trafic to the internal network that is comming from some of the other switches?

View 1 Replies View Related

Cisco Switches :: SG300 - Set Up VLan Only For Wi-Fi APs?

Mar 25, 2012

I want to set up a vlan only for the wifi APs and wifi clients on my network. They can't access to any server, only internet acces. I already implement this configuration and its working, but now I want to allowed a couple of laptops to connect to servers in other vlan. what should I do? Should I do it using Mac address of laptops or IP?

View 9 Replies View Related

Cisco Switches :: SG300-10P SYN Protection

Mar 1, 2013

Yesterday I upgraded my SG300-10P to firmware 1.2.7.76. I was curious about the new SYN Protection feature, but it seems to do nothing on my installation.
 
The switch is running in Layer 2 mode. I have ACLs in place and DoS prevention is not enabled. I also tried clearing ACLs and enabling DoS prevention. As I understood the Admin Guide enabling DoS in the Security Suite Settings is not necessary for using the SYN Protection.
 
In my firewall I see about 300 pps with SYN flags only arriving. What "they" do is sending me SYN packest to port 80 from forged IPs, so that my system should send SYN-ACKs to the victim system. In this case it is the Arab Bank. They are down at the moment...I think that is called a spoofed SYN flood attack.
 
So I thougt the SYN Protection feature should exactly solve that problem but it does not and does not show any "Last Attack" entries.
 
If I put a SYN filter in place it works, even if I put SYN Rate Protection in place. But that is just a dirty workaround. My firewall blocks those SYN packets with a SNORT rule.

View 1 Replies View Related

CIsco Switches :: SG300 Or SG500 That Has All Ports As SFP?

Feb 14, 2013

Is there an SG300 or SG500 that has all ports as SFP ports?

View 1 Replies View Related

Cisco Switches :: VLAN Config On Sg300?

Jan 26, 2012

I am using a couple cisco sg300 28P switches along with a sonciwall firewall/router. The sonicwall was already in place and working so they didnt want to replace it. I understand how to configure the vlan on the sonicwall, but could use some info on the cisco. I would basically like to create 3 vlans, 1 default for management, 2 for pc's on lan, and 3 for the cisco spa504g phones/'voip. Would i just go into the vlan managment, configure the 2 new vlans and give them two id's? These offices have one network drop, so the phones and pc's will be sharing the switch ports, however the phones have a setting to configure the vlan id so they know which one theyre on. Is there anything i need to do after that? I want to make sure that vlan 3 has the highest priority becuase its voice, is there some qos configurations i need to make on that switch as well? Also, the port that links the two cisco swtiches together, does that need to be set as "trunk" port? I understand what vlans are, but its just the first time ive run into these cisco models. .

View 0 Replies View Related

Cisco Switches :: SG300-10 IPv4 Routes Bug?

May 10, 2013

I bought the SG300-10 Switch a few days ago and updated it to firmware 1.3.0.59, but i think there's a bug in this firmware. If I go to "IP Configuration" IPv4 Routes" in L3 Mode nothing is displayed. In the log file i see that:
 
21474773112013-Mar-16 09:51:34Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB.       21474775182013-Mar-14 22:39:22Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB., aggregated (1)               
 
Reset of the Switch doesn't work.

View 4 Replies View Related

Cisco Switches :: SG300-10MP Keeps Crashing?

Sep 4, 2012

We are in an organization of 80 users with 5 Sx300 series switches with the latest firmware (1.2.7.76). The network is mostly flat with all switches feeding into a Cisco ASA5505 acing as the primary gateway for Internet Access. Only our two 48 port POE switches have an additional vlan configured for the VoIP phones. We have one SG300-10MP that is powering 5 Cisco Aironet 1024N's that keeps crashing. A couple weeks ago it went down twice in one day. I updated the firmware and it did not have any hiccups unitl today. This issue has been consistent since we installed the switch in April. Originally the issue seemed to be caused by too much bonjour traffic causing a buffer overflow (we have over 100 Apple products). Since I updated the switch I have not seen any bonjour buffer overflow errors. Instead I get the following error when it crashes:

2147424534 2012-Sep-05 15:12:28 Emergency %SYSLOG-F-OSFATAL: FATAL ERROR: tExcTask: ABORT DATA exception ***** FATAL ERROR ***** SW Version : 1.2.7.76 Version Date: 19-Jul-2012 Version Time: 17:54:43 Instruction 0x18 Exception vector 0x10 Program state register 0x80000092 %SNMP-I-CDBITEMSNUM: Number of startup configur ation items loaded: 133 %LINK-W-Down: gi1 %LINK-W-Down: gi2 %LINK-W-Down: gi3 %LINK-W-Down: gi4 %LINK-W-Down: gi5 %LINK-W-Down: gi6 %LINK-W-Down: gi7 %LINK-W-Down: gi8 %LINK-W-Down: gi9 %LINK-W-Down: gi10 %LINK-I-Up: gi9 %LINK-I-Up: Vlan 1 %LINK-I-Up: gi1 %STP-W-PORTSTATUS: gi9: STP status Fo

The CPU and PoE supply are far from being overloaded.

View 15 Replies View Related

Cisco Switches :: SG300 And Multiple WAN Connections?

Apr 8, 2013

Currently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
 
I'm considering adding a second cable modem. Can the SG300 handle that?

View 3 Replies View Related

Cisco Switches :: LAG Configuration On SG300 52 Switch?

Sep 10, 2011

I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?

View 2 Replies View Related

Cisco Switches :: SG300-10 VLAN Configuration

Apr 22, 2012

Before I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
 
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3.  I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved