Cisco Switches :: SG300 And Multiple WAN Connections?
Apr 8, 2013Currently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
I'm considering adding a second cable modem. Can the SG300 handle that?
Currently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
I'm considering adding a second cable modem. Can the SG300 handle that?
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedI have 2 SG300-10 switches, and I need two VLANs, one for internal network and one for WiFi APs.I need ports 1->4 on both switches to be part of 1st VLAN and ports 5->8 on 2nd VLAN; and port 10 uplink to 2nd switch.How I set up the VLANs and interface VLAN mode?
[code]...
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedI have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedI'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View RelatedI was assigned a task to configure an SG300-28P to have 3 different vlans.Now on VLAN1 their will be only one device configured with static IP 192.168.0.230,On the other 2 VLANS there will be a separate router connected on each one of them and will also act as a DHCP server.
View 4 Replies View RelatedI am using Cisco VPN client for windows 4.0.5 (C)I use the VPN client to connect to my office from home and to connect to a customer via their VPN connection.Is there any way that I can have these two VPN clients active at the same time instead of needing to diconnect one to connect the other ?
View 1 Replies View RelatedI am working on a project at my company. In short, there is one PC in the office to which other user must remotely connect to perform certain tasks. The stuff they do must be done from the machine with the specific IP, the IP of that machine, as this is specified in agreements with the companies we work with. So far, we have been using Remote Desktop (our machines are Windows-XP-based PC's), but this is quite annoying when more than one person needs to use the machine at the same time
View 3 Replies View RelatedI have a two broadband (Indian standards) connections that I want to use together. One is a 1mbps and the other is a 512kbps. The config that I have is below.
OS: Windows 7
Laptop: Acer Aspire
Router 1: Buffalo AirStation WHR-G54S
Router 2: ZyXEL P-600
I read about it on a few boards but I couldn't find any proper info on that.
I am trying to find out the availability of a router which will allow multiple connections, each with their own username and password and the ability for an administrator to control access.
View 2 Replies View Relatedi'm trying to setup multiple internet connections however the ISP i am using doesnt allow the use of NAT. DHCP and uses the registered mac address as a way to authenticate the account. To compensate for no NAT i use a web proxy feature on my router.[CODE]
View 2 Replies View RelatedWe are about to install a cisco 2911 router to replace a linux based router.
The Cisco will have 5 gig ports, 4 ports connected to DSL modems each modem connected to a different ISP, and the last port connected to a Cisco LAN switch.
802.1q will be used on the internal router port to split the LAN segments up into VLAN's as the building contains lots of different businesses.
Each customer in the building has there own servers and set of public IP addresses assigned e.g
Customer A - ISP 1 uses 81.34.65.78 NAT'd to 10.0.0.1 Vlan 5 port 25 (SMTP)
Customer B - ISP 2 uses 217.23.67.87 NAT'd to 192.168.1.1 Vlan 6 port 25 (SMTP)
and so on
The outbound traffic also needs to go out of the correct DSL line which ever has been assigned to that customer.
Am i right in thinking the only way to do this will be to use "Route Maps" ??
(IP addresses above are made up, or at least not ours)
The ethernet ports across the entire campus including the halls all host multiple networks via one port. I connect to the port and I get one connection, and my friend connects to get a second connection through the same port, and a third person connected via the same port to get yet another connection. I think there may be 4 connections being hosted through this in total. Now, the university have 3 main streams of internet: 1 for Staff/postgrad, 1 for students, 1 for exchange students. The fourth connection type is intranet with only access to a portal. The purpose of the portal is to submit your mac address for wireless and ethernet to be assigned an IP address for both. The issue we are having is my friend needs to connect to the exchange students connection for actual internet access, but the ethernet cable will only connect her to the portal (all her details have been submitted). I have cycled through every window in the networking control panel and usually issues like this I can resolve within a couple of hours but how to identify other networks that are available through ethernet.
View 3 Replies View RelatedI have laptop with windows 7 ultimate.i have two internet connection avalable...
1> wifi network of my office...which is protected by cyberom..so i cant open facebook and other restricted sites
2> internet through my android mobile...which is dialup connection or through usb tethering
i want to use office wifi for downloading via idm or other download manager and my mobile internet for social networking..or any idea i allow application to connect internet via perticuler network/way..
When I connect 2 laptops to my router, why does the speed/connection get split? I would understand that if the speed was maxed out or something but it's a lame 500 kb/s connection. Do all wify routers behave this way? It's kind of annoying since there's a trafic quota limit implemented and when someone downloads, the other one can't do s^&t? how to handle this?
View 8 Replies View RelatedI was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies View RelatedThere is a 6500 switch with fwsm. We have extended 2 vlans from the ISP into the FWSM. Also there are atleast 10 other vlans for our internal network. We would like say half of the internal vlans to go out of the 1st ISP vlan and the remaining half from the 2nd ISP vlan. Is there a way we can do this in the FWSM?
View 2 Replies View RelatedI need to look at options for terminating multple ADSL2+ circuits in the UK.Is it worth investing in a router to terminate multiple connections? Or do you think I could just use multiple 877 routers connecting to a good core multilayer switch?
View 1 Replies View Relatedwhat I want to do is setup a Tablet for use and share my one Internet connection with it and my desktop. I do not want the desktop and the Tablet networked with each other. there is a Tablet on Newegg: Velocity Micro Cruz Reader R103. the details say it's communication is 802.11b/g Wireless LAN. so I copy and paste that on Newegg and get: D-Link DIR-601 Wireless Broadband Router. not sure if that's what i need or what the configuration would be but I kind of know how to set it up.my question is can I connect a Desktop and a Tablet or any PC device to a router like this with out networking the individual units with each other? just to where it serves as more a splitter. is there any wireless alternatives to only "split" the Internet connection and not network the desktop and Tablet?
View 3 Replies View RelatedI have the setup as following on my PC:
[code]...
I use the fibre internet for almost all internet activities since the speed is fast.However, when I do school's stuff, I need to VNC to my lab's server. Hence I need to connect to school internet point. External IP cannot directly connects to my school's server.Therefore, I would need to force Windows (or VNC) to use the connection of the Wireless Ethernet card when I VNC to my lab's server. But I want to use my fibre for all other internet activities.
I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.
View 1 Replies View Relatedwhich product has the capability to receive multiple incoming connections
View 1 Replies View RelatedI have a belkin router that I've been using to share internet connectivity with several devices around my home. It has happily supplied this to an Ethernet connected desktop, Ethernet connected Blu-ray player, and wireless connections to two seperate laptop computers. When I try to add one more Ethernet (wired) connection to the mix, I always run into problems. Although the router has 4 outgoing Ethernet ports, it doesn't like to do more than two. Should I buy a new router? Cables?
View 4 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View Related