I need to look at options for terminating multple ADSL2+ circuits in the UK.Is it worth investing in a router to terminate multiple connections? Or do you think I could just use multiple 877 routers connecting to a good core multilayer switch?
View 1 RepliesWe have 2 Cisco ASA 5520 configured as Active/Standby with public IPs 68.171.xxx.xx6 and 68.171.xxx.xx7 respectively.We have 3 different vendors who are trying to access our Data Center. Do I have to have 3 different public IPs for these 3 different vendors? Or, just share the public IPs assigned to our 'Outside' interface?
View 3 Replies View RelatedI am trying to find out the availability of a router which will allow multiple connections, each with their own username and password and the ability for an administrator to control access.
View 2 Replies View Relatedwhich product has the capability to receive multiple incoming connections
View 1 Replies View RelatedI have a belkin router that I've been using to share internet connectivity with several devices around my home. It has happily supplied this to an Ethernet connected desktop, Ethernet connected Blu-ray player, and wireless connections to two seperate laptop computers. When I try to add one more Ethernet (wired) connection to the mix, I always run into problems. Although the router has 4 outgoing Ethernet ports, it doesn't like to do more than two. Should I buy a new router? Cables?
View 4 Replies View RelatedWe have a ZyXEL (P-2601HN-F1) router and three computers in our house. Currently, we only use cables to connect to the router because we haven't been bothered to setup wireless. However, there's a curious problem where the moment we connect more than 2 devices at a time, the router loses connection to the internet. To be precise, all LEDs are on, except wireless (d'uh) and Internet.
All involved computers run Win7.
We have a network, with a MAC filter for the internet acces. Every body can just have one MAC adress entry on their name for internet acces . My idea was to give the MAC adress of another router(that i can control), plug the LAN cable in the WAN of the second router, and then connect more computers to that router. Would that enable Internet acces for all the computers behind the 2 router?would it work if i make one computer with an extra network card, register that computers MAC adress and forward internet by the second network card to a router or other computer?
View 7 Replies View RelatedModel : TD-W8901G
Hardware Version : V3
Firmware Version : 3.0.1 Build 100901 Rel.23594
ISP : Ttnet
My web browsing/surfing speed decreases when I'm transferring files between other computers which are connected to this modem, and when a torrent client is downloading from 20+ seeds. I want to give the HTTP connections (port 80) the highest priority possible, so that my connection wouldn't delay when non-HTTP connections are active.The interface of the modem related to QoS settings are as below:What QoS settings should I enter (what rule(s) should I define) for giving HTTP protocol higher priority?
Information about my environment:
Modem product ID: TP-LINK TD-8901G
Modem firmware version: 3.0.1 Build 100901 Rel.23594
Modem hardware version: 3.1
My OS: Windows 7 Ultimate x64 SP1 My physical port: Enet1 (Eternet #1)
My local IP: 192.168.1.2
My torrent port: 5002
IP of the computer I'm transferring files between: 192.168.1.4
Physical port of the computer I'm transferring files between: Enet 2 (Eternet #2)
Region : UnitedKingdom
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : DEMON
I'm using parental controls to block all devices in the house from using tumblr. I cannot do this at a device by device level as it is being used on iphones/androids, laptops and desktops.Unfortunately, the way that tumblr works is that it use many URLs for the different pages people set up so it is not just a case of blocking url... - so I'm struggling to work out if I can do this via URL blocking on the router settings. How to do this at router level.
I am using Cisco VPN client for windows 4.0.5 (C)I use the VPN client to connect to my office from home and to connect to a customer via their VPN connection.Is there any way that I can have these two VPN clients active at the same time instead of needing to diconnect one to connect the other ?
View 1 Replies View RelatedI am working on a project at my company. In short, there is one PC in the office to which other user must remotely connect to perform certain tasks. The stuff they do must be done from the machine with the specific IP, the IP of that machine, as this is specified in agreements with the companies we work with. So far, we have been using Remote Desktop (our machines are Windows-XP-based PC's), but this is quite annoying when more than one person needs to use the machine at the same time
View 3 Replies View RelatedI have a two broadband (Indian standards) connections that I want to use together. One is a 1mbps and the other is a 512kbps. The config that I have is below.
OS: Windows 7
Laptop: Acer Aspire
Router 1: Buffalo AirStation WHR-G54S
Router 2: ZyXEL P-600
I read about it on a few boards but I couldn't find any proper info on that.
i'm trying to setup multiple internet connections however the ISP i am using doesnt allow the use of NAT. DHCP and uses the registered mac address as a way to authenticate the account. To compensate for no NAT i use a web proxy feature on my router.[CODE]
View 2 Replies View RelatedCurrently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
I'm considering adding a second cable modem. Can the SG300 handle that?
We are about to install a cisco 2911 router to replace a linux based router.
The Cisco will have 5 gig ports, 4 ports connected to DSL modems each modem connected to a different ISP, and the last port connected to a Cisco LAN switch.
802.1q will be used on the internal router port to split the LAN segments up into VLAN's as the building contains lots of different businesses.
Each customer in the building has there own servers and set of public IP addresses assigned e.g
Customer A - ISP 1 uses 81.34.65.78 NAT'd to 10.0.0.1 Vlan 5 port 25 (SMTP)
Customer B - ISP 2 uses 217.23.67.87 NAT'd to 192.168.1.1 Vlan 6 port 25 (SMTP)
and so on
The outbound traffic also needs to go out of the correct DSL line which ever has been assigned to that customer.
Am i right in thinking the only way to do this will be to use "Route Maps" ??
(IP addresses above are made up, or at least not ours)
The ethernet ports across the entire campus including the halls all host multiple networks via one port. I connect to the port and I get one connection, and my friend connects to get a second connection through the same port, and a third person connected via the same port to get yet another connection. I think there may be 4 connections being hosted through this in total. Now, the university have 3 main streams of internet: 1 for Staff/postgrad, 1 for students, 1 for exchange students. The fourth connection type is intranet with only access to a portal. The purpose of the portal is to submit your mac address for wireless and ethernet to be assigned an IP address for both. The issue we are having is my friend needs to connect to the exchange students connection for actual internet access, but the ethernet cable will only connect her to the portal (all her details have been submitted). I have cycled through every window in the networking control panel and usually issues like this I can resolve within a couple of hours but how to identify other networks that are available through ethernet.
View 3 Replies View RelatedI have laptop with windows 7 ultimate.i have two internet connection avalable...
1> wifi network of my office...which is protected by cyberom..so i cant open facebook and other restricted sites
2> internet through my android mobile...which is dialup connection or through usb tethering
i want to use office wifi for downloading via idm or other download manager and my mobile internet for social networking..or any idea i allow application to connect internet via perticuler network/way..
When I connect 2 laptops to my router, why does the speed/connection get split? I would understand that if the speed was maxed out or something but it's a lame 500 kb/s connection. Do all wify routers behave this way? It's kind of annoying since there's a trafic quota limit implemented and when someone downloads, the other one can't do s^&t? how to handle this?
View 8 Replies View RelatedThe reason I want to do this is to connect a DSL modem. I'm moving all my networking equipment to my utility room where all the cables come in to the house. All of the phone jacks are wired using Cat5. So, I want to take one of those Cat5 cables and terminate it with an RJ-11 so the modem can dial out.
View 15 Replies View RelatedThere is a 6500 switch with fwsm. We have extended 2 vlans from the ISP into the FWSM. Also there are atleast 10 other vlans for our internal network. We would like say half of the internal vlans to go out of the 1st ISP vlan and the remaining half from the 2nd ISP vlan. Is there a way we can do this in the FWSM?
View 2 Replies View Relatedwhat I want to do is setup a Tablet for use and share my one Internet connection with it and my desktop. I do not want the desktop and the Tablet networked with each other. there is a Tablet on Newegg: Velocity Micro Cruz Reader R103. the details say it's communication is 802.11b/g Wireless LAN. so I copy and paste that on Newegg and get: D-Link DIR-601 Wireless Broadband Router. not sure if that's what i need or what the configuration would be but I kind of know how to set it up.my question is can I connect a Desktop and a Tablet or any PC device to a router like this with out networking the individual units with each other? just to where it serves as more a splitter. is there any wireless alternatives to only "split" the Internet connection and not network the desktop and Tablet?
View 3 Replies View RelatedI have the setup as following on my PC:
[code]...
I use the fibre internet for almost all internet activities since the speed is fast.However, when I do school's stuff, I need to VNC to my lab's server. Hence I need to connect to school internet point. External IP cannot directly connects to my school's server.Therefore, I would need to force Windows (or VNC) to use the connection of the Wireless Ethernet card when I VNC to my lab's server. But I want to use my fibre for all other internet activities.
I have to connect/switch to two different ips different gateways, can I possibly keep two set of ips always ready.
View 1 Replies View RelatedI've got a problem with an ASR1004 running "asr1000rp2-adventerprisek9.03.02.00.S.151-1.S.bin".
When I'm performing extended ping tests using a tclsh script i'm geting this error message:
ASR_X1A2#ping 172.27.1.250
% Authorization failed.
When i'm pinging 12 diffrent destinations this happens to about 3 of them.
Checking the logs I found this:
Apr 24 19:42:56.071: %SSH-4-SSH2_UNEXPECTED_MSG: Unexpected message type has arrived. Terminating the connection
In my entire backbone this is happening only in this equipment, I've checked the connection between my ASR and the TACACS and it's OK, no packet loss. CPU and MEM are OK too.
ISP on each circuit cannot provide more than 3MB, so soon will get three circuit each of 3MB. ISP recommends to terminate all the links on Layer2 switch and have a trunk to the Router. I need all experts opinion on this proposed setup. We currently got 2811 with two GigaEthernet ports. We plan to have three GRE over IPSEC Tunnels (One tunnel for each circuit) to load balance/load Share/redundancy.
View 7 Replies View RelatedIs it possible to increase bandwidth througput on 2951 router if you have 3 WAN connections from different ISP, lets say 12Mbps + 24Mbps + 8Mbps, so will I get 44Mbps internet connection in total?Also, on 887G router, if I use DSL 12Mbps broadband, can I use 3G internet connection constantly, not for backup only. And will I get the total bandwidth output as a sum of two connections?
View 5 Replies View RelatedEverytime I disable SSID Broadcasting 2 extra wireless connections appear available connections list. (See wirelessconnections.jpg) One is blank and one is labeled Other Network. They disappear when I enable SSID Broadcasting. I am not sure why this is happening.
View 5 Replies View RelatedIs there any way to make it so that my computer has two internet connections, so to my router it looks my computer is two separate computers, and would this increase my speed, since my router is made for up to 15 connections and has only 300mb/s to give out, so [would]each computer is[be] only limited to 20mb/s? As of now I have a dlink xtreme-n DWA-552 adapter in my computer.
View 2 Replies View Relateddo not have fast internet service so we must need to combine two or more different internet providers and get one speed kindly reply do you know any router/modem/switch which can do this for us.
View 2 Replies View RelatedHow to make 2 (or more) connections work together and increase your final download and upload.You will need the following items
- A PC or server connected at high speed that is greater or equal to both connections speed (from a data center, You can get some very cheap $30 a month, a VPS can be good enough)
- 2 Internet connections at your home (DSL + cable for example)
- A router that supports dual WAN
- A Magic software that I can write for example
So what is needed is a way to split your data using some technology like the concept of RAID 0 (MAGIC software will be here used) and then use both IPs through the router to send the data to the server which will handle your request (it is possible to have a good usage of VPN here to forward all your traffic to the server without worrying about doing much work here). After that on the server you can reverse your RAID 0 data (using the same MAGIC software) and forward your request to the destination site that you want to visit. Same way the downloading will happen when the server receives a reply from the destination site, it will split the data using same RAID 0 technology (using the MAGIC software) and then send the data to both of your IPs. After that on your side you combine the received data (using the software) and you are done. Of course I do prefer the data splitting to happen using some hardware like a router with MAGIC software as it will be much more effective.
setting up a simple internet plan for a place, but a LAN center needs crazy fast internet, faster than most large enterprise class offices that take up an entire floor or two. Otherwise there is too much lag in games like first person shooters. We are expecting to have 60 computers, plus people bringing their own gaming rigs from home and laptops as well, xbox, ps3 and other consoles, all accessing the internet at the same time to varying degrees, with no room for lag. There is a LAN center in california that has 200 or more computers and they pay for 9 t3 lines, which is thousands and thousands of dollars per month. Plus the initial equipment to set that up from what I can find on cdw is many thousands of dollars also. Something like 10,000 for a router with 4 expansion bays, and 4000-6000 dollars for a t3 expansion card, bringing the total to around 22-28,000 for equipment to do just 4 t3's. Plus the monthly cost. Since we don't need all of the traffic to be secured like a high end business class line like a t3, I was considering what it would be like, and how one would set up, having multiple cable internet lines coming in. They make cable wic cards for cisco routers. 4, 50meg cable lines would give us 200 down and 40 up but I don't know how to make that work without having multiple public ip's. I was thinking that if I did have multiple public ip's on the network I could just divide the computers up so that they are in groups, using all of the public ip addresses for gateways, so that the load is split pretty evenly, but still, there should be a more seamless way to do this, I just don't know what it is. At the rate for business cable internet, 4 lines would probably only cost around 700 dollars a month, which is much better than probably 5 grand a month for several t3 lines.
View 3 Replies View RelatedI am a fairly basic configs that I just can’t figure out what I am doing wrong. I have what I would consider a fairly basic config that I just can’t seem to get to work and I am sure it is something I am just not doing or grasping. Basically I have two 3560 switches that I would like to connect together with four 1Gb ports and trunk four vlans across said port-channel, I created the port-channel and set it to switchport trunk encapsulation dot1q I then set all four ports to channel-group # mode on. With that setup I can’t ping from switch to switch on the nonnative vlan.
View 6 Replies View RelatedMy phone is a Nokia-N900, and I find the most useful way to interact with it from my PC is by ssh. Luckily it is possible to switch out the usb-networking module in the devices kernel to make it appear to windows as a generic RNDIS gadget. Plugging it into a windows PC I can now ssh into it, I can open an sftp session, everything works perfectly...
Except I can't access the web. I can't view other network resources. I look in the network connections section in the control panel and see my two connections, but I don't see any way to set which one to use for what. Seeing as I only use usb0 for ssh and eth0 for everything else, it seems I need a way to set it up so that usb0 only gets port 22 or something similar.
Is there any way to achieve this, or another method by which I could leave my phone connected to my Pc while using it for other network tasks?