ISP on each circuit cannot provide more than 3MB, so soon will get three circuit each of 3MB. ISP recommends to terminate all the links on Layer2 switch and have a trunk to the Router. I need all experts opinion on this proposed setup. We currently got 2811 with two GigaEthernet ports. We plan to have three GRE over IPSEC Tunnels (One tunnel for each circuit) to load balance/load Share/redundancy.
View 7 RepliesI'm seeing on an IOS VPN Tunnel interface which keeps going down and then back up...
We have a Cisco 2811 acting as a VPN Hub router on the backbone, which connects to various client sites over VPN. Of the 7 VPNs configured so 6 work well and are generally trouble free. The VPN interface on the other VPN keeps going down ,multiple times throughout the day, just recently the client has been noticing loss of connectivity. The remote router is managed over the VPN so there is always some kind of traffic over it.
*Sep 7 06:40:53.631: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to down
*Sep 7 06:41:23.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel111, changed state to up
[Code]......
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies View RelatedA multipoint GRE (mGRE) and IPSec tunnel is built between two routers. The topology of the device is briefied below:Configuration in End Router: This is a cisco 2811 router. Amoung 2 ethernet interface ,one is using for LAN and one is for WAN. In WAN part , we have configured mGRE (Tunnel1 and Tunnel 2)by creating sub-interface of the router. From the interface ,we terminating the link to MPLS cloud from there its pointing towards our core router.From End router we are advertising the path through EIGRP and from the cloud BGP advertisied to the core router.[code]
View 1 Replies View RelatedWe are facing network heavy and slow performance at one of our remote site, we are using Cisco2800 series router with same IOS on either of the sites.Our WAN network is running on BGP with EIGRP configured and tunnels were configured on either of the sites. As part of the testing I have removed the tunnel to see the performance was ok from Head office to remote branch and the WAN network is getting heavy and slow down when we put the tunnel back in hub and spoke.
quick info
Cisco 2800 Series router
IOS: (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)T1, RELEASE SOFTWARE
The reason I want to do this is to connect a DSL modem. I'm moving all my networking equipment to my utility room where all the cables come in to the house. All of the phone jacks are wired using Cat5. So, I want to take one of those Cat5 cables and terminate it with an RJ-11 so the modem can dial out.
View 15 Replies View RelatedI've got a problem with an ASR1004 running "asr1000rp2-adventerprisek9.03.02.00.S.151-1.S.bin".
When I'm performing extended ping tests using a tclsh script i'm geting this error message:
ASR_X1A2#ping 172.27.1.250
% Authorization failed.
When i'm pinging 12 diffrent destinations this happens to about 3 of them.
Checking the logs I found this:
Apr 24 19:42:56.071: %SSH-4-SSH2_UNEXPECTED_MSG: Unexpected message type has arrived. Terminating the connection
In my entire backbone this is happening only in this equipment, I've checked the connection between my ASR and the TACACS and it's OK, no packet loss. CPU and MEM are OK too.
We have 2 Cisco ASA 5520 configured as Active/Standby with public IPs 68.171.xxx.xx6 and 68.171.xxx.xx7 respectively.We have 3 different vendors who are trying to access our Data Center. Do I have to have 3 different public IPs for these 3 different vendors? Or, just share the public IPs assigned to our 'Outside' interface?
View 3 Replies View RelatedI need to look at options for terminating multple ADSL2+ circuits in the UK.Is it worth investing in a router to terminate multiple connections? Or do you think I could just use multiple 877 routers connecting to a good core multilayer switch?
View 1 Replies View RelatedI have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
I have an ASA 5540 cluster that is configured as my remote access VPN point. Users connect using IPSEC Profiles with Cert based authentication, the profile is configured to query two DHCP servers (infoblox appliance servers).
The problem I am encountering, is that I need to make reservations on the DHCP server for some users for specific business needs. What happens is that the ASA passes the request to the DHCP server with it's own MAC address and not the MAC of the remote host.
Is there any way I can configure the ASA to pass the request using the hosts actual MAC address?
I have a asa and Cisco 2811, needs to build a site-to-site ip sec tunnel between them. Due to a requirement need to encrypt inside traffic, i need to apply on the inside interfaces on both devices to build the tunnel.
I don't see a problem but just want to check if it would work on terminating on Inside interfaces on both ip sec peers.
I have 2 x WS-X4548-GB-RJ45 Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45) line cards in a 4500 chassis with 2 x WS-C4507R-E E-Series Super visor engines. We would like to create a layer 3 ether channel from a access layer switch terminating on our 4500 chassis. Can we configure the ether channel from the access layer switch such that one port on the ether channel is on one line card and the other one is on the other line card?
View 2 Replies View Relatedi have a 7201 router with NPE-G2. i have a design which i have the option to send all the traffic through a GRE tunnel or a L2TPV3 tunnel.which method is more CPU consumption ?
View 1 Replies View RelatedI'm in process of purchasing a new Cisco routers for our branches that will be used primary to enable IPSec virtual tunnel interfce with "tunnel mode ipsec ipv4". does the default IOS IP Base supports this feature? or i need to purchase DATA license or SECURITY license?
View 4 Replies View RelatedI am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies View RelatedThere are a few situations were I'd like to be able to use the locally configured account on a device but still have ACS in place.I want to complete this WITHOUT adding the locally configured account into ACS.I have tried setting the advanced option under Identity for if an account is not found to "Continue" however this causes the account to be allowed as long as a password is typed (any password, as long as its not blank).
View 2 Replies View RelatedMy setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies View RelatedI need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
I want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies View Relatedi have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies View RelatedI have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies View RelatedI want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I have a 2811 that I can remotely VPN to using Cisco VPN client however I cannot see the internal admin network (10.35.5.0).
Current configuration : 4845 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
I have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
I have a Cisco 2811 with an additional HWIC-4ESW card. [code] I need to NAT anything heading out of the WAN port. [code] I can ping anything connected to my other private networks from my 10.0.24.0 network but nothing on the Internet. [code]
View 3 Replies View RelatedI just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies View RelatedI want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
I have a 2811 ISR configured to provide the following services to my network: Internet access to LAN usersCisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations.Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 2 Replies View RelatedI've setup a NTP service by using Cisco 2811 routers. This works fine at the moment, but in the end there are some questions left.
1. I'm using two 2811 Routers, one for primary, which is resceiving the time from PUBLIC NTP 1, and one for backup, which is resceiving the time from PUBLIC NTP 2. Is it possible to compare these to times an check if the match? And if not, generate an alarm via e.g. SNMP
2. Is it possible to check via SNMP, if the routers are reaching PUBLIC NTP 1 and PUBLIC NTP 2 for sync?