how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies
I have a large quantity of ASA5520's and ASA5540's that need to be quickly assessed and RTV'd (if need be) if they are found to be upgraded ASA5510's.
My concern is because of this recent release-note by Cisco: [URL]
Is there a way to check the amount of DIMM slots on a unit through console or do I have to physically check each and every one?
I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies View RelatedI have a 2811 with 512 of memory installed (two by 256). The router has been sitting spare for sometime and I know there was once a memory problem with it long ago. It has two 256M Non ECC DIMMs installed and seems to work fine. I recently tried to install a 512M DIMM ECC and all I get is 'Unsupported DIMM" error - same if I remove the other 256M DIMM leaving just the 512M. I have tried three different DIMMs - and all have the same error message. One of the DIMMs is 'cisco supported' and based on what I can find in the web - seems to be the correct spec. I have also tried non ECC 512 DIMM and 'unsupported DIMM" error message is still coming up. If I did not know better, I would say that there was something that needed changing in the config to allow 512M DIMMs to be installed.
View 6 Replies View RelatedMy onboard eithernet quit working so I got PCI slot 1 and it doesnt work either I have 3 slots and none work. The pc won't even acknowledge that they are pluged in, but the lights on the card are flashing. Had it working once but when I moved it to my desk and booted it up nothing worked again. The PC will boot and run fine but no web. Clean install of XP and all is the same!
View 1 Replies View Relatedinternet on tv which has no Ethernet slot
View 3 Replies View RelatedI'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCurrently using a CSS1506 for our reverse proxy SSL.I have a couple of questions
1 - Does the 11506 use an internal disk as well as the one in slot 0 ?
2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 in case of a card failure in slot 0?
My laptop does not have a standard telepone line connecting socket. Is it possible to use a converter plug to use the boardband socket instaed?
View 2 Replies View RelatedJust finished my first build and everything went pretty smoothly but my wireless network card wasn't working. I noticed after I opened it back up that in order for my to screw the card in place it made the right side of the card tilt up.
So I just set it in the PCI slot correctly but there's no way for me to screw the card in place. I know my MOBO is set properly. My graphics card fits perfectly.
i have a brand new dell studio 1558
on my old computer i used an external PCMCIA modem from my cellular company , the modem uses a sim card to connect to the internet..
can i place the sim card inside the computer and use it as i used the previous modem ?
[URL]
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies View RelatedI've got this syslog alarm from nexus 7018. I am wondering what the slot 19 is here.
2013 Jan 15 23:59:22 r1 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is OPEN, Bottom Ejector is CLOSE
2013 Jan 15 23:59:24 r2 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is CLOSE, Bottom Ejector is CLOSE
Is it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedI bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedI have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies View RelatedI have a question for all those here who have experience with both Cisco ASAs and CheckPoint.Which do you prefer Cisco ASA or CheckPoint?
View 9 Replies View RelatedSimply one step away to check your IP address: type into your search box in your browser the following address
[url]....
I have a Cisco ASA5520 that we are going to use to allow users to connect to our network via the Anyconnect client, I have authentication set up to validate against AD via LDAP, but was wondering if there were any way to set up the profile to check the PC before they log in....we do not want users using their home PCs to attach to our corporate network, only PCs that were issued to them by the company. Nothing is jumping out at me in the config, we are running some fairly old sofware on the boxes (ASA - v8.2(2), Anyconnect - v2.5.3046) I plan on upgrading the Anyconnect to v3.1 but will probably need to keep running the 8.2(2) version on the ASA due to support issues.
View 2 Replies View Relatedi know in Cisco PIX til 8.2 OS, if i have Nat control disabled and ACL permitting connection from Low Secirity ( DMZ ) to High Secuurity (INSIDE) then connectino should be successful, and i dont need any STATIC identity nat of inside IP to be created.
But i have Cisco PIX 525 with Version 7.2(2) Which is not allowing connection from DMZ to INSIDE , although nat control is disabled. and giving RFP check failure, any thought?
PIT525PIXINET# sh running-config nat-control no nat-cont
packet-tracer input dmZ tcp 192.168.85.4 65000 10.34.21.25 3389
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
[Code]...
i have a router 1841 series and LMS send me amessage telling me the VPN AIM is not working on thsi device and i want to check the status of this VPN card
View 1 Replies View RelatedThe router is always giving the below error:
Error : compressed image check sum is incorrect 0xDC5C5348
Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
Some1 browse my PC via LogMeIn Hamachi, so i need 2 know who did that , how 2 see the log list?
View 1 Replies View RelatedHow do I check IP address of others, when in chatting or playing online game, I could only know that he is Mr. X from YZA country which appears on Screen, But I also know he is using with wrong name and wrong Country name.I would to check his IP as well as his Place?
View 1 Replies View RelatedI want to check the transfer speed between my PC and another IP.The IP belongs to a DVR here is the general schematic of the sistem:Digital Video Recorder - Dynacolor - DynaGuard H.264 DVR (nDG80 - nDG600 - DG200) & DynaHawk Speed Dome & IP CamerFirst when I've worked with this system everything worked well but now after three weeks I have to open 5 ore more internet explorer windows to see live image and I can't see the recordings.I need to know the speed transfer because I want to know if someone had decreased my transfer speed between my PC and the router or DVR.
View 3 Replies View RelatedHow to check which users are using printer. so that i can see which user are using more printer.
View 2 Replies View RelatedHow to check dhcp if not working
View 1 Replies View RelatedHow do i check my LAN connection speed- is the same as the speedtest t I run from the internet ?
View 1 Replies View RelatedAt one time a windstream (my internet provider) had talked me through a way to check the speed of my connections for my wireless network....I can' find the bookmark this was. How I can check this?
View 4 Replies View Relatedhow do i check the listed ip's on my server?
View 1 Replies View Related
