Is it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 RepliesI've just bought an access point AP1141N for my small business but unfortunately there is only Radio 0- 2.4G available through web interface. It is working fine but I would like to have access to radio 1 (5Ghz) as well.
View 2 Replies View RelatedWe ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies View RelatedI have an AP541N-A-K9. For the past couple weeks it stops work at 5:00pm. The clients can see the SSID but when they connect it fails. The only way to get this to work again, is to set the radio to 5GHz 802.11N. Setting the radio to anything else does not allow the clients to connect.
I have some older clients so I need this broadcast G as well.
I have upgrade the software to AP541N-K9-2.0(1). Does not make a difference. Reset to Factory defaulst and reconfig does not make a difference. There are no Rouge AP's in the area.
Between the issues these have passing DHCP from a Windows server and now this, I'm thinking these devices are not fully baked.
What Radio Channels are available for selection when operating the EA4500 in Wireless-N (5 GHz) mode only? I need to find a router that can be specifically set on channel 120 in the UK
View 8 Replies View RelatedI have been using the Asus RT-n53 for about a year now and had little to no problems with it. Lately, my wife's iPhone has been dropping its connection to the RT-n53. It was probably a problem with her piece of apple crap, but I thought I would update the firmware on the RT-n53. I found that my firmware was way out of date, so I updated to the latest version.
With the newest firmware installed, I can no longer detect the 5Ghz band with my PlayBook. Before the update, all of the other devices in the house were not 5Ghz capable, so my PlayBook was the only device that used the 5Ghz radio on the RT-n53. Now, the SSID for the 5Ghz band just isn't there any more. In the configuration settings for the RT-n53, everything points to "it should be working"... 5Ghz radio is enabled, SSID broadcast is enabled. I have tried changing the wireless mode from "N Only" to "Auto" to "Legacy". I have fiddled with channel settings, encryption settings, etc. Even tried changing the SSID a few times. Multiple reboot, and still, the 5Ghz SSID just doesn't appear on any devices.
We are using the CISCO-DOT11-ASSOCIATION-MIB in a Cisco Air AP 1140 device with release 12/4(21a)JA1 to find out the radio type of wireless client (B/G or N). The clients in question are of type Wireless N and Wireless B/G. We are querying cDot11ClientDevType and cDot11ClientRadioType but the relation between the returned values and client/radio type is not clear:
2 devices returned: cDot11ClientDevType = 102 ==> pc4500Client(102) - client with a 4500 radio and ClientRadioType=2==> ccxClient(2) - CCX- compatible radio1 device returned: cDot11ClientDevType = 1==> unknown (1) – unknown and ClientRadioType= 1==> unknown(1)
Questions: On a Cisco Air AP 1140 device
What OID needs to be polled to find if the client's radio type?What value is returned by this OID if the radio type is B/G?What value is returned by this OID if the radio type is N?
We use WLC 5508 with 7.4. We tried to set max allowed clients per AP radio to 30 through GUI. We have APs with 80 clients associeted though.
When entering config wlan max-associated-clients max-clients wlan-id we got
"WLAN/Guest-Lan/remote-lan is enabled. disable to configure max associated clients."
GUI doesn't show that message, should it? In GUI, Is it necesary to disable WLAN before too?
One of my Wi-Fi site, having cisco_1130AG access points nearly 110nos as of now i installed 80nos, after installing, in out off 80nos nearly 12nos of APs's radio is showing down.
Again i reset and re-configure then it is working fine, is there any readio (802.11g/a) problem in this model?
I am getting many radio resets on 1252AG access point on Wism1. The warning in WLC shows as : AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:c4:71:fe:5c:xxxx Cause=Reset on transmit completion. Status:NA cause = reset on transmit completion.I have fixed RRM to freeze and still same result.
View 5 Replies View RelatedI am looking into upgrading a customers wireless network and they are looking at using a few 1240 access points for both internal and external connections. Their question is can one access point support both channels simultaneously? They would like to connect an antenna on the inside of the building on the 5ghz channel and another externally on the 2.4ghz channel.
View 3 Replies View RelatedIn the old days I used two autonomous 1242AG access access points to create a 5GHz PtP link with 2 patch antennas (over small distance 50meters and on on private premises) to connect an small building or garage were there was no ethernet availible. and used the 2.4GHz radio to serve clients in the small building area, worked great.
Can I use the same setup with the 2602e access points? If so, would I be able to use them controller based? Can I connect a switch/or additional access point behind the 2602e (bridge) in the small building/garage? Would that addtitional access point be able to connect and register to the WLC.
By default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies View RelatedI have an E4200 V2. The 2.4ghz and 5ghz bands are both enabled and named differently. From what I've read they should both show up in the list of networks when I'm connecting other computers etc? All I'm getting is the 2.4ghz.Everything on the router is working fine as far as I can tell, just can't seem to access the 5ghz band. Maybe I recently upgraded to the Smart WiFi firmware but it's the same situation.The two bands have the same password with two of the first three letters switched on one.
View 3 Replies View RelatedI bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedUntil recently I used the 2.4GHZ band for my pc and my son used 5GHZ for his laptop on our D-link router.A couple of weeks ago our provider installed a new Cisco modem/router-in-one (the old modem didn't work any more). We use the D-link as a second router. The 2.5Ghz band is no problem but my son doesn't get internet access with 5Ghz
View 3 Replies View RelatedMy onboard eithernet quit working so I got PCI slot 1 and it doesnt work either I have 3 slots and none work. The pc won't even acknowledge that they are pluged in, but the lights on the card are flashing. Had it working once but when I moved it to my desk and booted it up nothing worked again. The PC will boot and run fine but no web. Clean install of XP and all is the same!
View 1 Replies View Relatedinternet on tv which has no Ethernet slot
View 3 Replies View RelatedWe have just finished installation of 12 AP 1552 as access points , clients are 7925G phone , after installation and configuration all clients can register and access to AP's in wireless environment but in IP we can't access to phones from our servers.For your information all phones and AP's and Ct5508 Controller are same subnet .We need install and configuer all 1552 just as Access points in 2.4Ghz , we don't need any mesh configuration.As for test we tried to connect to network by Laptop PC , it connected to access points but no network .
View 5 Replies View Relatedhow can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies View RelatedI'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCurrently using a CSS1506 for our reverse proxy SSL.I have a couple of questions
1 - Does the 11506 use an internal disk as well as the one in slot 0 ?
2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 in case of a card failure in slot 0?
My laptop does not have a standard telepone line connecting socket. Is it possible to use a converter plug to use the boardband socket instaed?
View 2 Replies View RelatedJust finished my first build and everything went pretty smoothly but my wireless network card wasn't working. I noticed after I opened it back up that in order for my to screw the card in place it made the right side of the card tilt up.
So I just set it in the PCI slot correctly but there's no way for me to screw the card in place. I know my MOBO is set properly. My graphics card fits perfectly.
i have a brand new dell studio 1558
on my old computer i used an external PCMCIA modem from my cellular company , the modem uses a sim card to connect to the internet..
can i place the sim card inside the computer and use it as i used the previous modem ?
[URL]
how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
Ive been struggling with this issue for a week now with an 877w (now with andvanced ip ios) in short my wireless network consists of
The internal dot11 sibinterface 0.11 radio (IP Address 10.0.1.1) which on bridge group 1 (IP Address 10.0.0.10) The SSID for the radio is on vlan 11 which has no ip address.
This works i can ping the internal network and internet
The guest dot11 sibinterface 0.10 radio (IP Address 10.0.3.1) which on bridge group 2 (IP Address 10.0.2.1) The SSID for the radio is on vlan 10 which has no ip address.
This dosnt work i get no no recived packets on the clients network stats and i cant ping any name servers or the radio ip address.The client is listed as being successfully accosated with the show dot11 assoc commmand
Ive tried taking the guest wireless and creating a new vlan for it (so its not on the same vlan as the tmg firewall interface) so that i have only the dot11 radio and vlan 12 on brige group 2 but the same thing happens no traffic on the guest vlan.
Ive turned off all authentication while testing this and the wireless network is currently in open mode until its fixed ive also only configured whats neccessry to test the wireless connectivity (no radius etc) that will be added later, Im also not using dhcp yet and the client is configured to the apporprite adderess staticly ie 10.0.1.1 10.0.3.2 its not a dhcp issue
!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!logging message-counter syslog!aaa
[Code].....
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies View RelatedI have a large quantity of ASA5520's and ASA5540's that need to be quickly assessed and RTV'd (if need be) if they are found to be upgraded ASA5510's.
My concern is because of this recent release-note by Cisco: [URL]
Is there a way to check the amount of DIMM slots on a unit through console or do I have to physically check each and every one?
A Cisco RV220W router/firewall connects the local LAN to the internet. The router is connected to a new Cisco SG300-28P switch configured in Layer 2 mode. There are two new AIR-1142N wireless access points running in autonomous mode connected to 2 ports on the SG300 powered through PoE. The AIR-1142N access points are running the latest firmware version 15.2(2)JB. There are two VLANs defined: VLAN1 is the native on all devices, and VLAN2 is for wireless guest traffic to provide access to the internet only.Internal/staff traffic is on 192.168.100.x, and the wireless SSID is MYNetS.Guest traffic is on 192.168.200.x and the wireless SSID is MyNetG.IP addresses are being assigned by the RV220W.
All works well with one exception. Wireless clients on the internal SSID are able to ping/access the switch, router, and other clients on wired ports on the switch. The router, switch, and wired clients can ping wireless clients. However, wireless clients, on the same SSID and the same 1142N cannot ping/access one another. They are being isolated from each other. We absolutely need to have this capability.The SG300 does not have port security enabled on any port. none of the workstations/laptops have a firewall enabled. These laptops are all Macs btw. I have checked that neither of the 1142N access points have Public Secure Packet Forwarding enabled on either of the VLANs.I am at a loss as to why the wireless clients are being isolated.
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies View Related