Just finished my first build and everything went pretty smoothly but my wireless network card wasn't working. I noticed after I opened it back up that in order for my to screw the card in place it made the right side of the card tilt up.
So I just set it in the PCI slot correctly but there's no way for me to screw the card in place. I know my MOBO is set properly. My graphics card fits perfectly.
i have a brand new dell studio 1558
on my old computer i used an external PCMCIA modem from my cellular company , the modem uses a sim card to connect to the internet..
can i place the sim card inside the computer and use it as i used the previous modem ?
[URL]
we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedI just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies View RelatedI have a Windows Seven desktop that will disconnect from the internet ( It has a Ethernet cable directly to the router ) after sitting still for a few hours.my laptop has a Wifi card and works even when the Desktop doesn't.
View 4 Replies View RelatedSeeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies View RelatedIm having a issue with that any of my computers without a wireless connection have been incapable of getting out on the internet with the new router that i got myself, i know the cables works etc, since they work perfectly fine with the old modem alone, but wont work at all with this unless on a computer with wireless connection
View 5 Replies View RelatedI think I am having problem with my network card I am running windows 7 with Dell wireless 1390 WLAN Mini-Card lots of times the signal is low and I get the error message no internet connectivity or some other error message that I am not being able to connect to the network provided by my wimax modem, Is there any program that I can download to test if there are any errors related to the network card or any way to fix this?
View 3 Replies View RelatedMy onboard eithernet quit working so I got PCI slot 1 and it doesnt work either I have 3 slots and none work. The pc won't even acknowledge that they are pluged in, but the lights on the card are flashing. Had it working once but when I moved it to my desk and booted it up nothing worked again. The PC will boot and run fine but no web. Clean install of XP and all is the same!
View 1 Replies View Relatedinternet on tv which has no Ethernet slot
View 3 Replies View RelatedMy laptop does not have a standard telepone line connecting socket. Is it possible to use a converter plug to use the boardband socket instaed?
View 2 Replies View Relatedhow can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
View 1 Replies View RelatedI'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
Currently using a CSS1506 for our reverse proxy SSL.I have a couple of questions
1 - Does the 11506 use an internal disk as well as the one in slot 0 ?
2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 in case of a card failure in slot 0?
Every one i want to know ws-c4503E series 3 -slot chassis . I have compatibility issues with MEM-C4K-FLD64M AND S45EIPBK9-12240SG will work.
View 2 Replies View RelatedI have a large quantity of ASA5520's and ASA5540's that need to be quickly assessed and RTV'd (if need be) if they are found to be upgraded ASA5510's.
My concern is because of this recent release-note by Cisco: [URL]
Is there a way to check the amount of DIMM slots on a unit through console or do I have to physically check each and every one?
I've got this syslog alarm from nexus 7018. I am wondering what the slot 19 is here.
2013 Jan 15 23:59:22 r1 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is OPEN, Bottom Ejector is CLOSE
2013 Jan 15 23:59:24 r2 %PLATFORM-3-EJECTOR_STAT_CHANGED: Ejectors' status in slot 19 has changed, Top Ejector is CLOSE, Bottom Ejector is CLOSE
Is it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies View RelatedI bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedI remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies View RelatedI have cisco 4510R L3 switch with installed 2 Sup on slot 5 and 6. the current active Sup is in Slot5 i want to make active Sup6 in slot 6 which is currently standby sup in chassis. Is there any way to make standby Sup to ACTIVE without reloading any of the Supervisor. however there is two way as per my understanding -
1. we can reload the active Sup so that standby Sup will take charge. - (redundancy reload shelf)
2. we can focefully switchover the state of Sup's by (redundancy forcefully swithover) but in above both cases reload will be performed by one of the supervisor. which i don't want.
There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies View RelatedThis past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
View 1 Replies View RelatedIn the bottom floor there are three computers, an iMac computer that receives an average wireless Internet signal, desktop computer and a laptop.I want to take care of the desktop computer and buy a network card, the next card:TP-Link TL-WN951NNow it has three antennas, each of its reception range is 2 dbiI should buy three of the 10 dbi antennas and connect them to the network card?It will give a good solution strong wireless signal and good speed?
View 4 Replies View RelatedData link-ARP,RARP, presentation-SSL,TSL,ASCII,JPG, Session layer-ASP(apple talk session protocol),SCP are these correct?can your provide 2 new protocols for each with the long name?
View 17 Replies View RelatedWe have two laptop computers and our Tivo hooked up to use the wireless internet through our cable company with a Belkin router. Over Christmas we got a camera that emails directly from it, and it told us to press the WSP button on the Belkin router. The camera magically worked, however our computers did not work anymore! After an hour long phone call to Belkin, I got one of my computers to work normally again. However the 2nd laptop won't connect to the internet and our tivo isn't picking it up either, which mean our shows are not recording.
Also, I'm using two apple computers. When I attempt to hook up the airport network, it says "unable to join the network."
"How do i setup a proxy correctly using firefox?"I forgot what addon it was that i was trying to use, proxy fox i assume. If there any better firefox proxy addon that i can use i will be happy to use.I want to know the steps to make the proxy work correctly, because i like to be anonymous as possible when using the internet. I don't care about internet speed.
View 3 Replies View RelatedOk so our company has a VPN set up on our workstation laptops for employees to be able to connect to the office network from home.We use CISCO VPN CLIENT, and a pre-setting .pcf file to upload our vpn into the client. The settings are correct completely to allow the VPN to work from home. All of our older workstations (Latitude D510-D630's) work with Windows XP SP3 32b. Recently i purchased new laptops (Latitude E6410's) and have started issuing them out with Windows 7 Enterprise 64b.A couple employees from home cannot get their VPN to work correctly at home with the New Laptops. Their old laptops work fine with the VPN, but the new ones dont. They are running a Frontier DSL modem with wireless.The VPN connects just fine on the new laptops, but the problem is... Nothing works. Outlook does not connect, They cannot access any of our network shares or drives. And cannot use any of our company's software that requires our network access.
I tried uninstalling the the CISCO Client, and reinstalling it, No Go.I tried changing the MTU Settings on the client and network adapters and wireless adapters, No Go.And it seems to be just an ISSUE with employees trying to VPN through a dsl connection using the new laptops, where others with the new laptops can VPN in fine through a time warner connection. But remind you, their old laptops work fine.. which seems kind of odd to me.
I have 3 ACS 5.2 servers both here and in the US. On friday night, our building lost power and it came back up early saturday morning. During this, the Wireless controllers dropped their configs and reverted back to point to the old ACS servers again. After fixing this, all wireless works now in my location. But, ACS is not logging my sessions even though i can connect to wireless with phone or laptop. It should log the authentication process if the server is here or in the US, but it is only logging for the other 2 servers. now on a weird note, the VPN for users in this location is authenticationg just fine.
View 2 Replies View RelatedI am user of Dell Inspiron 1545 and I have problem with Internet. Till yesterday everything just worked great, when I was turning on a wi fi, it always found a network I wanted to. Yesterday, the current has been cut of. (?) and I lost connection to internet. After current camer back, everyone got internet back, but not me. My wi fi is still finding almost all networks except one, the most important one.
View 1 Replies View RelatedI use the Windows7 Virutal WIFI when traveling abroad to give my Iphone an internet connection in my hotel.I've had zero issues until this week. The WIFI connection is still showing up on my iphone, but I no longer get internet access (I only get an IP and subnet on the iphone now, no router or DNS info). The issue began (coincidence or not) as my MagicJack downloaded and installed a software update. MagicJack support says they aren't the issue. I experimented with created an Ad-Hoc network...no change. I've removed and reinstalled the wireless card and driver. No change. I suspect some corruption with ICS, but haven't found any solutions online to fix it.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Richard-PC
Primary Dns Suffix . . . . . . . : MARCOGROUP.local
[code]....
I have hardware version B1, firmware version 2.00NA and several computers (wired & wireless) with Vista & Win 7 x64 and a Brother HL1440 printer.When I print something it comes out scrambled, images missing or cut off, empty pages, etc. This same setup worked fine when it was directly into one computer, then shared on the network though windows sharing. The problem was that computer had to be running to print off the network. I got the dir655 since it had printer sharing but so far its not been of any luck.
View 5 Replies View Related