I am looking into upgrading a customers wireless network and they are looking at using a few 1240 access points for both internal and external connections. Their question is can one access point support both channels simultaneously? They would like to connect an antenna on the inside of the building on the 5ghz channel and another externally on the 2.4ghz channel.
View 3 RepliesWhat Radio Channels are available for selection when operating the EA4500 in Wireless-N (5 GHz) mode only? I need to find a router that can be specifically set on channel 120 in the UK
View 8 Replies View RelatedI have read various forum postings saying to get the best performance from a wifi router you have to use channel 149 or greater and that 36-48 have a weaker signal strength and thus less range/speed.I live in New Zealand and when I select the wireless channel drop list for the 5GHz band it only lists 5 options - Auto (dfs), 36, 40, 44 and 48. I have read forum posts of people stating you should switch to 149 or greater and I have seen screenshots showing the drop list with 149 selected. But I don't have that option.If I check the Status > Wireless page it shows that channel 36 is being used (for Auto).Am I doing something wrong? Do E3000's in this part of the world not support 149 etc?I spoke in a live chat to a support rep who told me that all E3000's are the same everywhere in the world and there was little to no difference in firmware between them. I was also told that channels 36-48 are high gain channels and so there is no need for the other channels, which contradicts other articles I have read which state 36-48 are weaker channels.
View 2 Replies View RelatedI just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies View RelatedIs there anyway to monitor client who is downloading , using the most bandwidth in Cisco wireless environment ? i have 1240 ap and 4400 controller environment.
View 1 Replies View RelatedI need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedI have 6513 which have wism and sup 720 , for some reason the access points keeps on going up and down the port channels created automatically but i cannot see any configuration inside it as shown below .I tried to edit the interfaces and add the trunk configuration but it cannot be modified . [code] the Wism status is showing up but the APs Number regestered keeps on going up and down the version running on the sup 720 is 12.2(33)SXI5 and the wism is installed in slot 9.
View 5 Replies View RelatedHow would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedI had a new AIR-AP1042N-N-K9 access point and I tried to convert it into lightweight mode with the image c1140-rcvk9w8-tar.124-21a.JA2.tar . I used all the methods but the AP is getting hanged at one position after decompressing the new IOS. The capture of the process is below: [code] After this I am getting the junk characters and everytime AP hangs at this position.
View 4 Replies View RelatedIn the old days I used two autonomous 1242AG access access points to create a 5GHz PtP link with 2 patch antennas (over small distance 50meters and on on private premises) to connect an small building or garage were there was no ethernet availible. and used the 2.4GHz radio to serve clients in the small building area, worked great.
Can I use the same setup with the 2602e access points? If so, would I be able to use them controller based? Can I connect a switch/or additional access point behind the 2602e (bridge) in the small building/garage? Would that addtitional access point be able to connect and register to the WLC.
By default, 802/11a/n is set for backhaul communication.Does that mean that if most of my clients are on 5ghz, Mesh network is not a preferred design to go? Reason being:- client communication on a/n radio might disturb the traffic of the whole cell and of all the MAPs that connect to the network through that MAP.
View 6 Replies View RelatedIs it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies View RelatedI have an E4200 V2. The 2.4ghz and 5ghz bands are both enabled and named differently. From what I've read they should both show up in the list of networks when I'm connecting other computers etc? All I'm getting is the 2.4ghz.Everything on the router is working fine as far as I can tell, just can't seem to access the 5ghz band. Maybe I recently upgraded to the Smart WiFi firmware but it's the same situation.The two bands have the same password with two of the first three letters switched on one.
View 3 Replies View RelatedAP not booting and am not able to boot. Xmodem file system is available.flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an errorduring initializion of the flash filesystem. The followingcommands will initialize the flash filesystem, and
[Code]....
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
We have four VLANs that need to be accessible to wireless devices. The VLANs serve the following groups: staff, student, guest, phone
We are currently using a WEP/MAC authentication for staff and phone wireless networks.
I am looking for what your recommendation would be to provide reasonable level of wireless security, particularly with the staff network, but at the same time not require a high level of management, ex. managing active and inactive MAC addresses for MAC authentication. We have the following components available - 1240 APS, Windows AD, a 4402 WLC, and 6 campuses, and outdated Cisco ACS.We need to provide connectivity to Cisco wireless phones, laptops, iPads, cell phones.
Cisco 4404 WLC
AP 1240 - LWAP
Wireless client receives a DHCP address from central DHCP server fine. Unable to route outside of own subnet . Continuous ARP WHO HAS (Default Gateway addr) TELL (client IP) messages being received. WLC running OS 4.2.99.0.
We successfully use this oid on our Aironet 1240 series AP's to list the dot11 associations to the AP:1.3.6.1.4.1.9.9.273.1.2.1.1.18 (cDot11ClientSubIfIndex).However, that oid does not work on our Aironet 1140 series AP's. Any equivalent oid?
View 0 Replies View RelatedI'm trying to find a document in Design Zone about configuring a Wireless AP and I wasn't able to find it. I have a good experience configuring switches, routers and firewalls in CLI and this is the first that I have my hands on APs (1240 AG).
View 2 Replies View RelatedI had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
We are using WLC4402 for our Aironet 1240AG access points. The clients are connecting to the access points and are authenticating to the RADIUS server. I am seeing the logs in Server 2008 but they are being rejected due to Network Policy on the NPS server.
Where do I see the Authentication Type on the WLC4400 or the 1240's? In order for the clients (authenticated via Active Directory user) I have to set the Authentication in the NPS Connection Request Policy to "Allow clients to connect without negotiating an authentication method".
I do not have a certificate on the server and my method options are MS-CHAP-v2, MS-CHAP, CHAP, PAP, SPAP, and allow without negotiating. This RADIUS server was moved from Server 2003 IAS to Server 2008 NPS and there were no issues in Server 2003 IAS. I have all authentication methods allowed and it still gives me the error below. Only when I check "Allow clients to connect without negotiating an authentication method" it allows the authentication to proceed.
Client Machine:
Security ID: NULL SID Account Name: Fully Qualified Account Name: OS-Version:
Called Station Identifier: 00-17-a2-87-54-00: SSID NAME
Calling Station Identifier: 00-41-96-b6-e3-27
NAS:
NAS IPv4 Address: 192.168.90.24
NAS IPv6 Address: -
[code]...
Reason: The user attempted to use an authentication method that is not enabled on the matching network policy.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
I have a 5500 controller that we use to manage our lightweight access-points. We have had complaints that the 'guest' vlan in the boardroom is not usable. Our guest vlan is in fact overloaded.
I went back to the original site survey and noticed that coverage for the room is not ideal so I would like to have a new lightweight access-point installed in the boardroom and somehow limit the access to it to only a few people.