Cisco Wireless :: Client Access To AP1552
Oct 22, 2012
We have just finished installation of 12 AP 1552 as access points , clients are 7925G phone , after installation and configuration all clients can register and access to AP's in wireless environment but in IP we can't access to phones from our servers.For your information all phones and AP's and Ct5508 Controller are same subnet .We need install and configuer all 1552 just as Access points in 2.4Ghz , we don't need any mesh configuration.As for test we tried to connect to network by Laptop PC , it connected to access points but no network .
View 5 Replies
ADVERTISEMENT
Jun 30, 2012
I am expanding coverage in a big outdoor area.Most of the area is covered with AP1552 with AIR-ANT2506 5,2 db antennas.At the border of the area i have some masts where i can place ap's.Would it make sense to use directional antenna's there? I have a big open area where it is not possible to place ap's.The only placement is a mast in the middle of the area.I have a AP1552 with 5,2 db antennas there.Can i get better coverage if i place 3 or 4 ap's with directional antennas ?Or should i try with a 12dBi AIR-ANT24120 ?
View 2 Replies
View Related
May 14, 2013
I used the AP 1552 Link Calculator to determine the coverage area of my AP deployment, however I have some concerns.I would like to know what the maximum radio range refers to when using an omni-directional antenna. Is this distance the radius or diameter of the coverage area? [code]
View 1 Replies
View Related
May 5, 2013
how to configure AP1522 in my possession.
I have 2 AP1522 and I have to configure them so that clients can connect either 2.4 GHz or 5.0 GHz. Each of the two AP1522 must be autonomous, but has to bear in mind that are close together.
To do this I have:
- Defined the two AP1522 as RAP mode
- Set the flag on the "client access on backhault link", but I have not enabled the sub-flag "Extended backhaul Client Access" (what is this sub-flag?)
- Set 2 BGN different (but this is indispensible or I can put the same BGN? what is the difference?)
- Set the two AP1522 on two different channels (but this is necessary? or is importan only if I set the same BGN?)
- The two AP1522 appear on the WLC as a way bidge (is correct?)
How can I check if my laptop will connect using the 5.0 GHz?!? It's just turn off the antenna of 2.4 GHz?!? On my laptop I haven't found a way to force it to connect in 5.0 GHz.
View 5 Replies
View Related
Jul 18, 2012
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
View 4 Replies
View Related
Oct 11, 2012
Ive been struggling with this issue for a week now with an 877w (now with andvanced ip ios) in short my wireless network consists of
The internal dot11 sibinterface 0.11 radio (IP Address 10.0.1.1) which on bridge group 1 (IP Address 10.0.0.10) The SSID for the radio is on vlan 11 which has no ip address.
This works i can ping the internal network and internet
The guest dot11 sibinterface 0.10 radio (IP Address 10.0.3.1) which on bridge group 2 (IP Address 10.0.2.1) The SSID for the radio is on vlan 10 which has no ip address.
This dosnt work i get no no recived packets on the clients network stats and i cant ping any name servers or the radio ip address.The client is listed as being successfully accosated with the show dot11 assoc commmand
Ive tried taking the guest wireless and creating a new vlan for it (so its not on the same vlan as the tmg firewall interface) so that i have only the dot11 radio and vlan 12 on brige group 2 but the same thing happens no traffic on the guest vlan.
Ive turned off all authentication while testing this and the wireless network is currently in open mode until its fixed ive also only configured whats neccessry to test the wireless connectivity (no radius etc) that will be added later, Im also not using dhcp yet and the client is configured to the apporprite adderess staticly ie 10.0.1.1 10.0.3.2 its not a dhcp issue
!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!logging message-counter syslog!aaa
[Code].....
View 4 Replies
View Related
Apr 3, 2013
A Cisco RV220W router/firewall connects the local LAN to the internet. The router is connected to a new Cisco SG300-28P switch configured in Layer 2 mode. There are two new AIR-1142N wireless access points running in autonomous mode connected to 2 ports on the SG300 powered through PoE. The AIR-1142N access points are running the latest firmware version 15.2(2)JB. There are two VLANs defined: VLAN1 is the native on all devices, and VLAN2 is for wireless guest traffic to provide access to the internet only.Internal/staff traffic is on 192.168.100.x, and the wireless SSID is MYNetS.Guest traffic is on 192.168.200.x and the wireless SSID is MyNetG.IP addresses are being assigned by the RV220W.
All works well with one exception. Wireless clients on the internal SSID are able to ping/access the switch, router, and other clients on wired ports on the switch. The router, switch, and wired clients can ping wireless clients. However, wireless clients, on the same SSID and the same 1142N cannot ping/access one another. They are being isolated from each other. We absolutely need to have this capability.The SG300 does not have port security enabled on any port. none of the workstations/laptops have a firewall enabled. These laptops are all Macs btw. I have checked that neither of the 1142N access points have Public Secure Packet Forwarding enabled on either of the VLANs.I am at a loss as to why the wireless clients are being isolated.
View 5 Replies
View Related
Sep 23, 2012
Is it possible to connect directional antenna on slot 1 5Ghz radio on the 1522SB and use it for client access ? As per the deployment guide there is a note that Omni antenna is required on slot1. If i connect directional antenna on slot 1(how will the AP know if its omni or dierctional antenna which is connected anyway) , will it work ?
View 3 Replies
View Related
Jan 25, 2013
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies
View Related
May 7, 2013
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
View 12 Replies
View Related
May 29, 2009
I have scoured your website and the web.I do not have the CD rom that came with my WAP54G wireless access point (misplaced) and now need to configure the WAP54G, but for the life of me, i cannot find the link to download client software to configure it anywhere.Could the network admin please post the link on your website to download it, or could they send me a private email with a link, so that i can download, then install it, so that i can use the wireless access Point?
View 6 Replies
View Related
Jun 29, 2012
Using VPN client 5.0.7 Able to get vpn ip address But cant access remote desktop or any network inside, I was able to access before But I dnt known what changes happen on my laptop which is unable to access now ,I have reinstall the client again but no use' Able to access the same vpn & rdp with another laptop & also other users can access' Except my laptop What can be the issuse with my laptop.
View 1 Replies
View Related
Oct 19, 2011
I have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies
View Related
Jan 25, 2013
why my client can't internet access from my config
(INTERNET)-------->[ROUTER]---->[CLINET]
Clinet :
Ubuntu LTS 12.04
IP 192.168.100.2
Netmas 255.255.255.0
Gateway 192.168.100.1
DNS Server 202.134.1.10
View 7 Replies
View Related
Nov 17, 2011
Completly new to Cisco ASA and need to get this working ASAP.ASA 5505 8.4(1) is the secondary FW and I need for it to allow everything going out and block everything coming in but for the VPN clients. Since a Cisco moron, I used the ASDM and it's wizards to make this work, which might explain my situation.
[code]....
My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x server or service (tried telnet, RDP, ping, etc.)
View 2 Replies
View Related
Mar 13, 2013
I've found that my clients can NOT access to my ASA 5510 with their Cisco VPN Client Ver 5.0 through IPsec over UDP.By comparing my new running config with the old one I found some strang following configuration: [code]
We have 3 diffrent IT expert who have access to our router and I think this configuration is cause of our VPN access problem.Is it really because of that or something else.Any way I want to know how can I get rid of these configuration?
View 7 Replies
View Related
Jan 3, 2012
There is a Cisco VPN client (running on Windows 7) and an ASA5505. The goals are client could use remote gateway on ASA for Skype and able to access the devices in ASA inside interface.
The Skype works well but I cannot access devices in the interface inside via VPN connection. Following is the config, how to correct NAT or VPN settings?
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password wDnglsHo3Tm87.tM encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code].....
View 3 Replies
View Related
Jan 22, 2011
I have A setup in different location with the the ASA Firewall with VPN enabled and a Print server. on Network B i have a server with 2008 installed and its my NAT server, DNS and File server.Now the Client on Netwrok B wants to access the Server in Network A Remotely through VPN they could connect to but cannot user Remote Desktop either its Ip translation issue or i dont know.
View 2 Replies
View Related
Apr 12, 2011
I want to set up our ASA5505 firewall to allow access from the Cisco VPN Client software.I have nstalled the client software then tried using the VPN wizard to set up the connection without success, I am running Windows 7 32 bit and Cisco client 5.0.03.0530. [code]
View 22 Replies
View Related
Apr 12, 2012
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
View 1 Replies
View Related
Mar 10, 2013
I have an ASA 5505 that is on the perimeter of a hub & spoke vpn network, when I connect to this device using the VPN client I can connect to any device across the VPN infrastructure with the exception of the sub net that the client is connected to, for instance:
VPN client internal network connects to 192.168.113.0 /24 and is issued that ip address 192.168.113.200, the VPN client can be pinged from another device in this network however the client cannot access anything on this sub net, all other sites can be accessed ie. main site 192.168.16.0/24, second site 192.168.110/24 and third site 192.168.112/24. The ACL Manager has a single entry of "Source 192.168.113.0/24 Destination 192.168.0.0/16 and the "Standard ACL 192.168.8.8./16 permit.
View 14 Replies
View Related
Jun 4, 2012
used to be able to access pc usieng fing now can not access used fing.Accessed a win 7 client with my android. Reset the router now i can not access the win7 but able to access 2vista a different win7 pc and able to access other devices on nerwork. Can see the win 7 machine in question but can not connect with samba client.
View 2 Replies
View Related
May 11, 2011
i have server 2008 machine..how can i access windows 7 as client system?
View 1 Replies
View Related
Jul 17, 2012
I had an odd occurrence today on my network. One particular desktop running Vista could not access secure websites (httpsremoved the DHCP lease on my server (Windows 2008), let the desktop pick up a new address and all is good nowThis is a production network (domain) environment
View 3 Replies
View Related
May 28, 2012
I'm trying to solve a disastrous networking (via workgroup nightmare) and I cannot enable the DNS Client on my Windows 7 PC. I go to cntrl panel, admin services, dns client, and try to change it to automatic and it says "access is denied"
View 1 Replies
View Related
Jul 5, 2012
Recently a router crashed and some suspicious about the client arised. The point is that now the order is to deny all kind of router admin access for the client. I was thinking, is this a good idea or will be better to give him limited access to the router, to avoid the client to try to access the router at all cost? Something like to stop the motivation to crack the router password.
View 7 Replies
View Related
Aug 4, 2011
On my Windows 7 laptop, after connecting to my office Network using Cisco VPN clientThe entire Internet is utilized by the VPN. I am unable to browse the internet on my computer till I disconnect the VPN Client.
View 3 Replies
View Related
Jun 18, 2011
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies
View Related
Apr 2, 2013
I have a 2811 Router (config below) with VPN configured. I can connect through the VPN and access devices on the native VLAN but I can't access the 10.77.5.0 (VLAN 5) network (I don't care to access the 10.77.10.0 - VLAN 10 network). This issue has been plagueing me for quite a while. I believe it's a NAT or ACL issue. VPN client IP pool is 192.168.77.1 - 192.168.77.10. [code]
View 4 Replies
View Related
Feb 7, 2012
I'am using ASA5510 and I configured a VPN IPSEC. When I connect to the vpn with a windows client ( using windows vista) , I have access to the network ressources but when i want to go on the Internet it doesn't work. (particulary with Internet explorer, it works with Firefox!) Furthermore,On other windows client I haven't this problem.
View 4 Replies
View Related
Nov 23, 2012
Trying to setup client VPN access on a 1841 router. essentially i would like to connect using the cisco vpn application.
View 2 Replies
View Related
Jun 5, 2011
we use the Cisco VPN-Client to connect to our CISCO1921 Router and want to go out again on the same interface to the internet. We configured the connection with the IOS scurity package, have no split tunneling - so the client is forced with it's default gateway to our router - we also have pushed our local dns-server to the client and he gets dns results. Now I think we have to got out with some kind of NAT, because our client has a private IP from the IPSec Client pool. At the moment we have no NAT inside/outside, bacause we only use official IP addres in- and ouside (data-room usage).
- Is it possible to get the NAT function going in and out on the same interface with crypto_map IPSec user comming in and going out to the internet ?
- Is it more secure to configure this with vrf ?
- Has some a link to example configurations for this ?
View 4 Replies
View Related
May 6, 2012
I purchased a RV042 V03 router with firmware version 4.1.1.01-sp (Dec 6 2011 20:03:18) and I need to create a VPN connection through a remote client. I added a new tunnel in the "Client to Gateway" section, so I created a VPN client access, but connecting remotely by the QuickVPN Client after the connection and testing of the network I get the error "the remote gateway is not respondig, do you want to wait?" and I'm not able to establish a connection to the network. I can provide remote access directly to the router and the IP address to connect remotely.
View 3 Replies
View Related
