Cisco VPN :: 1921 - Internet Access Via VPN Client Tunnel
Jun 5, 2011
we use the Cisco VPN-Client to connect to our CISCO1921 Router and want to go out again on the same interface to the internet. We configured the connection with the IOS scurity package, have no split tunneling - so the client is forced with it's default gateway to our router - we also have pushed our local dns-server to the client and he gets dns results. Now I think we have to got out with some kind of NAT, because our client has a private IP from the IPSec Client pool. At the moment we have no NAT inside/outside, bacause we only use official IP addres in- and ouside (data-room usage).
- Is it possible to get the NAT function going in and out on the same interface with crypto_map IPSec user comming in and going out to the internet ?
- Is it more secure to configure this with vrf ?
- Has some a link to example configurations for this ?
How can I configure an ASA 5505 NEM client to allow access to the Internet when the tunnel to the headend is down? I am planning on deploying back to back ASA 5505s in network extension mode but I do not want to block Internet access on the client side if the tunnel to the server should go down.
I recently purchased a Cisco 2911 to replace my Cisco 1711 router. I copied the configuration from the Cisco 1711 router to the Cisco 2911 router. Everything seemed to work correctly except when I VPN tunnel into the Cisco 2911 router using Cisco's VPN client version 5.0. I can ping the router LAN interface from my PC that is VPNed into the router but I can no longer ping or access the devices on the LAN side of the router as I did on the Cisco 1711 router. I don’t see errors in the log or hits blocking anything in the acls. It’s using the same configuration that I had on the Cisco 1711 router, and this did work on the Cisco 1711. The Cisco 2911 router is running IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1).
Here is the VPN clinet portion of the configuration: The LAN is addressed as 192.168.0.0/24. The router LAN interface is 192.168.0.1, which I can ping and access. I can't ping or access anything on the LAN (192.168.0.0/24) beside the router.
aaa authentication login vpnclientauth local aaa authorization network vpngroupauth local ! crypto isakmp client configuration group remote-clients key 6 xxxx pool clients [Code]....
The ASA has one public IP on its outside interface and using PAT to the internet. It only has two interfaces, inside and outside using vlan. I created a IPSec VPN through CLI. My goal is for the remote client to browse the Internet throught tunnel.
Q1: Is it possible?
Q2: The remote side gets connected and has IP from the pool, with is part of inside network. But it cannot ping anything, including the gateway, which is the inside interface. I debug it, it shows the ASA receives the ping packages, but it doesnt send anything back to the client.
I have been playing around with a 1921/K9 router in our dev environment. It's been about 24 hours and I just can't seem to get it to work. My DHCP Server is working hence my internal network is getting IP address as desired. But Router doesn't seem to connect to internet for some reason.
I am trying to make it a internet facing router with static IP address (67.210.209.113). LAN side of this router will be our .11 Network which is our Dev Network.
Here is some network information:
WAN: Interface IP: 67.210.111.111 Default Gateway: 67.210.111.222 (I can ping this address through router) tlm1921A-11A#ping 67.210.111.222
I have the same 1921 router that I am trying to install at a facility with a Static IP address and Static DNS information to get on the internet and I cannot get the 1921 to access the internet!
Here is my config:
Building configuration... Current configuration : 4072 bytes ! ! Last configuration change at 09:51:57 Chicago Sun Feb 26 2012 by fbcpekin ! NVRAM config last updated at 09:51:58 Chicago Sun Feb 26 2012 by fbcpekin
we have a cisco ASA 5505 and are trying to get the following working:
vpn client (ip 192.168.75.5) - connected to Cisco ASA 5505
the client gets a specific route for an internet address (79.143.218.35 255.255.255.255 192.168.75.1 192.168.75.5 100) when i try to access the url from the client i get a syn sent with netstat when i try the packet tracer from the ASA i see the following:
I am trying to configure an IPSEC tunnel on a 1921 router. What I hope to accomplish is that using a IP SLA that the IPSEC tunnel will only be brought up IF the normal WAN connection is not responding. My thoughts were to route the traffic that needed to come back to corporate through a loopback interface but I havent found a way to do that.
I've been trying to set up my new Cisco 1921 Router to provide internet access to my local network but with no success. I've been reading guides and looking at videos and I have to be missing something becaouse I can't access internet (ping/tracert) from my local network.
The DHCP server works fine and the clients on my local network gets ip-adresses from the router but can't ping or tracert outside the local network.
Equipment Cisco1921, HWIC-1ADSL, 2 x GB Ethernet interfaces (Only one used for local LAN) Software IOS Version 15.1(1)T2..I have been asked to configure this router to provide an IPSEC tunnel back to our central office.We have been provided with an ADSL business class 7MB service from Telecom Italia, they have presented the circuit to our office with no terminating equipment (wires only). Telecom Italia have provided us with some IP addressing information as follows (I will not disclose the entire IP address) [code]
I can see that the packet count is increasing both inbound and outbound on the ATM interface. I have read many documents and tried many different way to try and get this resolved, I even logged a call with Cisco but no dice.
My ISP has just implemented a new network on the cable infrastructure which uses a PPTP authentication method. It works on my Cisco RVS4000 router as there is an option to set PPTP as the WAN type. The only trouble with the RVS4000 is that the performance is very poor, hence I am trying to get it working with a Cisco 1921. I have looked high and low and I cannot find an sample of a Cisco router functioning as PPTP client to a ISP.Enclosed is the screen shot of my Cisco RVS400 with the options etc.
We are using a CISCO1921-SEC (ISR) with IOS 15.1 and we configured a "crypto isakmp client configuration group". We can connect with the "Cisco System VPN Client Version 5.0.07.0410" via IPSec/UDP.
1. Is it possible to push routing informations to the System running the VPN Client ? A the moment all traffic is routed to the tunnel but we like only one route to the network permitted with "pool ..." in the "crypto isakmp client configuration group NAME" section.
2. We searched for changing from upd connection to tcp connection via special port. Is it possible with IOS 15.1 on the CISCO1921-SEC ? Is there something possible like "iskamp ipsec-over-tcp port 10000" ?
(Router is ISR 1921)This is doing my head in. I am not using NAT, there are no ACLs, there is no split horizon.Here is what I have. It is practically generated by CCP. When connected I cannot ping the loopback interface or the gig0/0 interface, (not to mention anything else).
version 15.0 service config service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname dcsgw1
I'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 ) C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp *Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA *Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987 *Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068 [Code]...
I have a couple a questions answers on which i cant google for a period. BTW maybe i simly use wrong aproach to choose keywords.
1) Is it possible to assign same ip address to the same client each time it authenticated, preferably without using DHCP? Im definely sure that it possible but cant find corresponded configuration examples (my device is Cisco 1921 with IOS 15.0.1).
2) Is it possible to assign dynamic crypto map to loopback interface (the purpose to make EASY VPN Server accessible through two interfaces - maybe you recommend other approach instead?) - as i move workingcrypto map from phy int to loopback - i cant connect with reason "Phace1 SA policy proposal not accepted"
getting internet access via a easy vpn tunnel on a cisco 877 router. Basically we would like roaming users to be able to use the internet via the vpn rather than using a split tunnel. The reason for this is we have multiple sites that are tied down via external IP access lists for some services. We would like roaming users to be able to interact with these sites through the central router and use the routers external IP address to acess the secured sites. I know we can use a proxy but we also use some other non proxy bases services at these sites so would rather direct routed access.
I've create many s2s vpn tunnels before, but this one I just can't seem to get going. It's just a simple Site to Site VPN tunnel using preshared keys. Below is the running config for both routers. [Code] ..........
We have ASA 5540. We setup Site-to-Site VPN and Remote Access VPN (Cisco VPN client). If are running full tunnel on the Cisco VPN client, the internet access is slow. For example, when we are running full-tunnel, the internet speed is 16 Mbps based on Speedtest.net. When we go to Speedtest.net, some of the graphics do not load. If we are running Split-tunnel, the internet access speed is 78 Mbps based on Speedtest.net and the Speedtest.net web site loads all the graphics.
I have setup a site-to-site VPN tunnel between 2 sites using CISCO rv120w.Everything works fine; any PC on one site can access all systems on the other site and vice-versa.The issue I have is when I start a VPN connection another site on Internet using IPSecuritas.I can initiate a VPN to site 1 and site 2; but when connected, I can only access servers that are located into the same site I'm connected to; I cannot ping the remote site.The Range of IP addresses on the internet during my tests is 192.168.11.0 (I 'm using a Mac)
-Systems with IP 192.168.1.1 and 192.168.10.1 are bridges -Systems with IP 192.168.1.2 and 192.168.10.2 are CISCO rv120w
I want to connect my clients from the Windows WS to a VPN Tunnel using 3925 router w/o Cisco VPN client. Is there the way to use native IPSec client on Windows XP or Windows 7?
I have successfully setup the AnyConnect VPN (connecting to our ASA5510) and have split tunneling configured. My remote users can access inside LAN servers as well as the Internet from their remote location. What I would like to know is is it possible to change the split tunnel and not allow access to the Internet from the remote location but force the remote client to go through the VPN and out our internal edge firewall to the Internet? Basically I need my remote clients to access the Internet but I would like for their Internet traffic to go through the VPN and out our edge firewall. This will allow the same security as if they were sitting in the office.
Is it possible to configure remote access (IPSEC client) to force all traffic through the tunnel (no split tunnel) yet still limit the internal hosts that can be accessed?
I have been asked to provide remote access (via ASA5510) with the following requirements:
- the client should have unrestricted internet access via the ASA (the source address will appear to be the outside interface of the ASA)
- the client should have access to only two internal hosts (192.168.10.10 and 192.168.44.10)
Is there a way to limit access to those two internal hosts, while still providing secured internet access? The only way I can see is to use an access list on another device (for example our core switch).
On my Windows 7 laptop, after connecting to my office Network using Cisco VPN clientThe entire Internet is utilized by the VPN. I am unable to browse the internet on my computer till I disconnect the VPN Client.
I'am using ASA5510 and I configured a VPN IPSEC. When I connect to the vpn with a windows client ( using windows vista) , I have access to the network ressources but when i want to go on the Internet it doesn't work. (particulary with Internet explorer, it works with Firefox!) Furthermore,On other windows client I haven't this problem.
I have implemented a Clientless SSL VPN solution with Smart-Tunnel feature on Cisco ASA 5520, software 8.4(4)1.I have been successful in making Bookmarks which employ Smart-Tunnel feature to avoid content rewritting (if any). And in reality it works fine with some links. However there are some links to an Oracle portal, it doesn't work.I was able to log into the Oracle portal with its username/password. However when i click into a button of the drop-down menu, nothing happens while normally there should be a box appearing. The Oracle portal runs with some Java stuffs which i don't really know as i am not a programming engineer anyway.
I have remote branches that connect to the corporate office as a site-to-site VPN. Now the clients at the branch are getting an application that is using an unsecured port (tcp/23). I would like to use a set of ASA 5520's that I have at the corporate office, with the AnyConnect license on them. I want the client machines to establish a tunnel from the client to one of these ASA's. The ASA' then would have a connection to the VLAN that the receiving server is housed on. The trick is to just establish the tunnel from the client to the ASA that will allow the IP of the client to not be translated. So I would use the ASA as a security 'pass-through' for the clients that use this new application.
I would like to know whether I will be able to setup a VPN tunnel between a wireless router and wireless client on the same network. What I plan to do is to first setup up my router to use DD-Wrt as its OS. I have read some tutorials on the Internet, about how one can configure a VPN server when using this router OS.Now if I assume that I have a client on the same WLAN network who is already connected and so on; - can the client connect to the router's VPN server and then connect to the Internet using the VPN tunnel that has been established? The purpose of this configuration is to see whether if this setup (if it can actually be configured that way) would protect against wireless man in the middle attacks that use trivial tools such as Cain and Abel.
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.
I've been labbing on my asa5505 at home, setting up different VPN solutions for testing purposes. However, I can't get my anyconnect client to establish a DTLS tunnel when connecting (anyconnect only shows tls, and does not display any errors about not connecting with dtls)I have set dtls port to 444 and this port is open on the other side.
i`ve setup smart tunnel with different applications. (mstsc.exe, putty.exe). This works fine. I`ve now tried to add the vSphere client appliaction (VpxClient.exe). But i don`t get it working.
