Have spa module on 6509E experience that error:
!
sh log | b crash
SLOT 3: Aug 18 12:52:10 CST: %CARDMGR-2-ESF_DEV_ERROR: An error has occurred on
Ingress ESF Engine: Control Store Parity Error
SLOT 3: Aug 18 12:52:10 CST: %ESF_CRASHINFO-2-WRITING_CRASHINFO: Writing crashin
fo to disk0:crashinfo.esf_20110818-175210
[Code]....
I'm trying to connect my new Dell Dimension 8400 (3.0Ghz/512Mb/XPsp1) to my home wireless network. I installed two diiferent PCI adapter cards in my one available PCI slot -- an older D-Link (11b) and a brand new Netgear (11g) (which Dell Sales assured me is compatible). Both cards detected my Netgear wireless router and provided an excellent internet connection, so I'm assuming they were seated properly. The problem is that every time I shut down the system I get the blue screen of death with the following message:
-Hardware Malfunction
-NMI: Parity Check/Memory Parity Error
-The System has halted
The system runs and shuts down perfectly when the PCI cards are removed. D-Link and Netgear Support technicians told me I have to contact Dell, but Dell Support doesn't seem to have an answer for me. Which wireless PCI adapter cards are truly compatible with Dell hardware?
I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies View Relatedwe have two 6509E which are configured in VSS mode with the following modules in each:
1 48 CEF720 48 port 10/100/1000mb Ethernet
2 8 DCEF2T 8 port 10GE
3 4 CEF720 4 port 10-Gigabit Ethernet
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
I need to know if the temperature of the attached modules are normal or there is a problem?
the status of one of the supervisor engines is "MajFail" as shown below:
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
5 Major Error
We are facing a strange issue, our ACE 20 got failed due to power issue , after RMA once we are installing ACE 20 to 6509 , the status LED is showing ORANGE . The sh module shows it as " Others " ... The IOS is same as it was previously in 6509 .
View 2 Replies View RelatedConfiguration: VM with ACS 5.4 with patch 3. (upgraded from 5.2.0.26 patch 10)When I go on "System Administration" - "Administrators" - "Administrative Access Control" - "Authorization", I got this error:
What I tried:
"acs backup" on this server and shutdown
Install an ACS 5.4 with patch 3 on new VM --> I don't have the problem on GUI
"acs restore" to restore my configuration on new server --> I got this problem again...
I want to use this feature...After this error, others pages generate this error: I have to reload server or restart management service to get him back...How could I solve this? (I don't want to reconfigure manually the server )
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
View 3 Replies View RelatedI've just bought all-in-one router X2000.And I found that in the parental control [ADD] windows does not show every device's name.It shows only 3 of 20 devices (ex. My-nb, PCaccount, PChuman, but the others show "Network device").
View 1 Replies View RelatedDay before yesterday my Laptop [Dell Studio] has suddenly stopped working and i have to shut it down forcefully. Then i logged in again but my wireless was not working, i have googled the solutions and tried to start the WLAN Autocofig service but its throwing an error : 1053 : The service did not respond to the start or control request in a timely manner.I have Windows 7 installed on my system.Suddenly the speed of my laptop reduced drastically. Now its taking almost 12 mins to start instead of 2 mins.I have also removed some lines from the test files from the registry as mentioned in the below website as a resolution, but its not working.Unable to connect to wireless networks on Windows 7 Enterprise laptop. I dont have OS [Operating system's] CD as it was pre-installed on my laptop when i bought it.
View 2 Replies View RelatedIs there I can customize the error page which is shown when someone visits a blocked site
View 3 Replies View RelatedI am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies View RelatedWe have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active) SerialNo : SAL1521E035
Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port 1 2 3 4 5
-------------------
U U U . F
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.
I had a problem during setup of a new module N7K-M148GS-11 into a Nexus 7000 10-Slot chassis.The module was powered-dn and removed by platform with the following message: [code]
Do I need to upgrade nx-os? There is a workaround?
I've got a pair of N7010's in a vPC domain with some FEX's attach running NX-OS 6.0.2. I am experiencing port failures on my N7K-M132XP-12L module the port got shut down due to internal errors with Error Disabled status and I am not able to bring the port back up. I am getting the following errors when I try to reset it. I am hoping is not hardware related as my vPC peer-link is on this module and I only have a single N7K-M1 32 XP-12L in each N7010. Replacing the module will be painful. [code]
View 7 Replies View RelatedCisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies View RelatedI have a Cisco catalyst 6513 with sup720-3bxl and WS-X6724-SFP modules , the switch was working fine until yesterday ,but after a maintenance the modue WS-X6724-SFP failed to bring online , the error code is (Module Failed SCP dnld) does it mean the module has hardware problem or i need to replace it ?
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ios version
s72033-adventerprisek9_wan-vz.122-33.SXH7.bin
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
show module
Mod Ports Card Type
Model
[code]....
Just brought an ipod and downloaded itunes but my laptop wont connect to the itunes store, it says basically it cant connect and that i need to take a look at my network settings? I have this same problem with steam aswell and got so frustrated i ended up deleting it even though i have games on there.
View 7 Replies View RelatedSituation: I have a File server, name is \fileserver and ip address is: \192.168.1.254The shared drive on the server is split into 2 folders which are: Data and HomeI have 17 laptops which all connect to these folders via a group policy which maps the L: to Data and the H: to Home. On 4 of the laptops, for some reason I can't access the Home folder as I get an access denied message. I am the administrator and have full rights. On the other 13 laptops it works fine. I have found that if I try connecting using the IP address \192.168.1.254Home, it works fine.[CODE]
View 10 Replies View RelatedI'm trying to authorize managment access for HP ProCurve Manager via ACS RADIUS. But I get the failure: 15015 Could not find ID Store Machine is configured under Network Devices and AAA Clients, the sevice selection rule selects the correct access service, Access Service is Network Access, authorization profiles = permit access.
View 2 Replies View Relatedi can access app store on my iphone at home and other broadband connections but cant access at work. thinking if it would be the asa thats stopping htis. i have allowed port 3689 but no joy.
View 3 Replies View Relatedare the connections between the ACS and external identity stores encrypted?I know that when setting up LDAP identity store there is the option to specify SSL conection. Are the other connections encrypted by default, or is the data sent between the ACS and AD, for example, sent in the clear?
View 3 Replies View RelatedUsing Sha1 for Cisco 7925g and sha256 for data. Two separate CA's, one EnTrust (SHA1) the other Local Wondows CA (SHA256); ISE can only use one at a time to process a particular protocol (ie..EAP-TLS, HTTP, etc...) As a result we have to have a separate PSN just for Wireless and Wired VoIP (which can only hold SHA1 RSA1024).
View 5 Replies View RelatedWe use Cisco LMS Prime 4.1 to archive our Cisco Equipment configurations.
Now we want to store the configurations off site.
My dad has an issue with his Windows 7 home edition laptop, he cant get any updates on AVG, Itunes or access the itunes store, he keeps getting error messages denying access. Hes using the 64bit Itunes lastest version (I uninstalled his very out of date itunes last night and downloaded the new version) but still the store wont open
View 14 Replies View RelatedMy Location Free has recently stopped letting me access the App Store, Itunes store and Facebook. Someone suggested I change the channel, but not sure how to do that.
View 1 Replies View RelatedI have a cisco ASA 5505 . I need to store " show capture 'word' ( where is a variable) output to syslog server for analyzing packet and port .
View 2 Replies View RelatedThe following messages are filling up my syslog.
*spamApTask0: Nov 09 15:59:29.071: %LOG-3-Q_IND: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
*spamApTask3: Nov 09 15:59:27.616: %CAPWAP-3-REASSEM_SPACE: capwap_ac_reassembly.c:652 Unable to store capwap fragment from 88:f0:77:b6:fd:00.
What could be causing it? I am using 1524 APs in a Mesh environment with a WLC 5508 (7.0.116.0) which is connected to a H3C switched network.
The MAC addresses above are from my MAPs and I don't think I am getting it from the RAPs.
I have Switch 6509E wich is the core of the network, and we have 4 llink form 4 ISPs, all the link will work at the same time?how can I confiugure the BGP , as I know if I configure bgp it will work with one ISP as an active link,if that link goes down it will automatically begin to work with other ISP. My question is that how can configure the network so that,some vlans work with one ISP, some vlans with the others and so on.If configure it with route map I will have to track every time to change the confiration if the links goes down, but I do not want to track it, Can I do anything with BGP to implement this task?The core of the network is Switch 6509E, intervlan routing is implemented on it, no dynamic routing is enabled.The firewall module installed on it the implementing the NAT processes.
View 7 Replies View RelatedIs P S 3 the best way to connect netflix to TV and can you store movies in the P S 3 Hard- Drive
View 1 Replies View Relatedhow can i store urls used by the client side in the server using java
View 1 Replies View RelatedIs it possible to have emails stored automatically on a network drive after email is been read by the user? I know for sure that on a mailserver there is a feature that can be set up to have a copy stored and than send it to the users application.
View 1 Replies View RelatedMy WRT54GS worked perfectly till 3days .. everything works perfectly it just that i cannot get connection to itunes store neither over wifi or on my pc .. when i disconnected my router and connect my pc directly to the modem .
View 1 Replies View RelatedI can't download an app from Google Play Store. I can download from my 4G network but not the wifi - Belkin F5D8236-4 V3. Google troubleshooting says the firewall is blocking the 'ports required for Google Play to download (TCP and UDP 5228) on that network.' However, with the firewall 'disabled,' the download is still not working.
View 4 Replies View Related