Any way of narrowing down a degub for a peer address only? For example, I currently run 'debug crypto isakmp 127' which captures everything, but can I run the same dVPN debug for peer address 1.1.1.1?I know you can run 'sh crypto ipsec sa peer 1.1.1.1'.We're using an ASA5520 (8.4.2).
View 2 RepliesWe are trying to add an additional LAN-to-LAN IPsec VPN to our network. We currently have one remote office connected, when we configure the second VPN matching the first the tunnel never begins to establish. There is an ACL that is dening the static IP for our remote office.
The layout is as follows:
Main office = ASA 5520
Remote Office A = ASA (Unknown Model)
Remote Office B = Adtran Router
All devices have static IP addresses.
We used the ASDM VPN wizard to create both VPN's.
We have created a rule allowing all traffic from our remote office IP, and that had no effect on the VPN aside from eliminating the following message from our logging:
4 Mar 19 2012 15:18:01 106023 67.50.19.230 50234 TWT-hq-e 31326 Deny udp src TWT-outside:67.50.19.230/50234 dst inside:TWT-hq-e/31326 by access-group "outside-in" [0x0, 0x0]
We have verified that both sides are configured the same however the VPN never is initiated so as of right now the ASA is simply blocking all attempts from our remote office to connect.
I am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View RelatedWe have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View RelatedI've been using an ASA 5505 -- ASA 9.1(1) -- with an IPSec Remote Access VPN. Everything works properly, though I recently noticed that when my IPSec session is disconnected, I get the standard message ID 113019, but within that message the Peer IP address is incorrect. In fact, it isn't even close to my actual remote address. [code]
When I first researched the IP, I found it coming from China, which freaked me out. I changed settings, rolled back to 9.0(1), and nothing worked. Finally I rebooted, reconnected the VPN, and the IP changed. This time it was an address from RIPE NIC. I rebooted again, now an address from ARIN in the USA. One more reboot, now a random Comcast residential address.
Within that boot cycle, the peer address always stays the same. I've connected from different devices, different IPs, different ISPs - nothing matters. Additionally, there are no firewall logs for these IP addresses at all.
ASA Remote Access VPN peer addresses in disconnect message are incorrect and change at reboot.
We have several remote sites with Linksys WRVS4400N and Smoothwall firewall/vpn devices. I need these sites to be able to connect to multiple dis-contiguous subnets at our main office. This was easily done with smoothwall and linksys. You create a separate tunnel for each subnet and voila, you're done. However, when I tried this with our newly installed ASA, it will not let me create multiple tunnels to the same remote peer address. This is a problem since these sites only have a single static public IP address. Am i missing something or does the ASA not allow connections to/from multiple subnets form a site with a single peer address?
View 13 Replies View RelatedI am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies View RelatedI got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies View RelatedI am facing issues in blocking Peer to Peer applications in LAN. I am using 881 Cisco router and below is the config done. [code]
View 1 Replies View RelatedI recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies View RelatedI bought my WAG320N, I too have the internet drop out and from reading in here is a very common problem. Cisco really should bring out a new firmware version and address this issue. Any way you can block peer to peer file sharing with the WAG320N? If so how do you go about it?
View 1 Replies View RelatedOne of the schools whose networks I administer has a peer to peer network running about 30 xp machines. DHCP is achieved and DNS settings distributed via a basic Linksys router; is there any way of distributing proxy server address and port short of entering manually in LAN settings of IE on every terminal - there is no budget to install a server.
View 4 Replies View Relatedi just set up my 2Xp pc's and one windows7 laptop peer to peer for file and printer sharing but i can not configure internet connection for those pc's
View 2 Replies View Relatedi want to set up my two computers /win xp/ installed using peer to peer network , just tell me the needed steps
View 2 Replies View RelatedI am currently working with a vendor to get my ASA5520 setup to handle IPsec VPN connections for my clients and we are stumped with how to get the outside interface to respond to connections/requests.
I work for a state agency and our network connectivity is provided to us by another agency/department. The firewall I want to use for VPN connectivity has an outside address of 10.0.8.162 which is not routable outside the state's network. I have been assigned a set of public IP addresses for servers in my DMZ and I am wondering if it is possible to configure the ASA to utilize one of those public IP addresses for VPN communication. My DMZ network is setup as a local 192.168.10.0 network and the ASA is performing NAT translations to the corresponding public IP addresses.
Putting in a NAT rule to translate one of the public IP addresses to the 10.0.8.162 outside interface, but I wasn't sure if that would work.
I want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies View RelatedI have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
how we immplement the same on ASA 5510.
I'm having a weird issue with an ASA 5520 (Ver. 8.2) of a customer. The scenario is as follows:
There is a sub net (on a sub interface) "Guest" which basically is allowed unlimited access to the internet. Traffic is source Na Ted through the ASA to the outside interface. This works fine.
There is on the "inside" interface a server which can be accessed from the outside via a public IP address. On the ASA this is implemented as a static NAT entry. This also works fine.
Now the customer wants to access the server on the inside from a client of the "Guest" interface using the public (Na Ted) IP address. Reason for this is, they have an application with hard programmed IP address inside and want to run some life tests. However, this kind of traffic seems not to be passing through the ASA.
What I have tried so far:
- examined, if a hairpin scenario could be applied here, but it seems not, as I have traffic traveling between interfaces not out and in to the same interface.
- enabled the option "enable traffic between two or more interfaces which are configured with same security levels" and also "enable traffic between two or more hosts connected to the same interface"
- when I use the real addresses of the host, it works, so it shouldn't be an issue with the firewall rules
So any reason why I cannot use the public NAT address from any of the other interfaces?
I am having an issue with the user VPNs. For users connected via the AnyConnect VPN client, all of their Internet traffic goes out their local Internet connection, since I am using split tunneling. However, I need a specific public IP address to go through the VPN tunnel and out the DIA at the main office, rather than the user's local internet connection. I managed to have this IP address go through the tunnel to the ASA at the main office, but it appears that it gets blocked somewhere there, or maybe the return traffic gets blocked. I am using an ASA 5520 at the main office, with software version 8.3.
View 3 Replies View RelatedISP assigned us the following:xxx.yyy.zzz.32/30 as the outside interface network.This means .33 is the next hop, gateway, or default route.This means .34 is the outside interface on the ASA.xxx.yyy.zzz.64/26 as the ip address pool.This means xxx.yyy.zzz.65 to xxx.yyy.zzz.127 is the address pool.xxx.yyy.zzz is identical in all cases.Addresses .35 through .63 are owned by other parties and are not usable to us.The 33-34 setup works using static routing - IPSEC VPN is setup and functioning properly using these addresses.
[ie. Route outside 0.0.0.0 0.0.0.0 xxx.yyy.zzz.33]
After NAT and ACL entries are created to provide altnernate external IP address on the outside interface [ie. static (inside,outside) [external ip] [name] netmask 255.255.255.255 and access-list [name2] extended permit tcp any host [alternate outside ip] eq https], attempting to browse to an internally hosted website from an external IP address results in the following messages in the ASDM log.
6 Apr 14 2011 17:58:51 110003 [redacted external IP Address] 37763 [Internal Website Name] 80 Routing failed to locate next hop for TCP from Outside:[redacted external IP Address]/37763 to Inside:[Internal Website Name]/80
How do I setup routing for this non contiguous address range?
Our firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
i have 3 access-list configured IN | Out on my Border router (MARTIAN) ,i have to look which one block some of the traffic passing through ,for that matter i have enabled the below commands on my ISR 2900: with nothing output.
View 3 Replies View RelatedWhat is difference between Peer to Peer network and point to point network???
View 5 Replies View RelatedMy tunnel had been running fine for a couple of months. Now, not so much.Here is some debug.
View 6 Replies View RelatedI have been using "debug ip packet" on a Cisco 2921 running IOS 15.1(4)M1. The problem I have is that, although I am using an ACL to limit the output, I am seeing some output that is distracting from what I am trying to see. Specifically, I am seeing the following:
Mar 19 20:22:36.135: IP: s=192.168.20.253, d=224.0.0.2, pak 30DB6D4C consumed in input feature , packet consumed, MCI Check(80), rtype 0, forus FALSE, sendself FALSE, mtu 0, fwdchk FALSE
[ code]...
These would appear to be HSRP messages. But I don't understand why they are appearing when I configure "debug ip packet 101". The ACL is pretty simple:
access-list 101 permit icmp host 96.87.145.1 host 192.168.20.1
access-list 101 permit icmp host 192.168.20.1 host 96.87.145.1
So I thought the implicit "deny ip any any" would block these messages. I even tried to block them specifically using an extra line:
access-list 101 deny udp host 192.168.20.253 host 224.0.0.2 eq 1985
But still they show up!
Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedUsing 'debug ip packet acl# det on a 2911. On an older Cisco router you could set up an ACL
access-list 150 permit tcp any any eq 1023 and then run debug ip packet 151 det and this would give a good debug output for any traffic matching a TCP port of 1023.Now when I try this on a 29xx ( Version 15.1(4)M3 ) I get the screen filling with a lot of multicats HSRP communications.
I have tried rewriting the acl to have other deny statements after the permit to limit the source or destination hosts and/or the ports but the HSRP data is still there.
like this
access-list 150 permit tcp any any eq 1023
access-list 150 deny udp any any eq 1985(code)
how to debug an ACL I've created on a 4404 WLC, specifically I want to monitor what packets are being denied by the ACL as something that should be working isn't
I've created an explicit deny statement at the end of the ACL and verified that the counter increases each time I try the problem software update.
What I can't work out is how to get the WLC to tell me what packets are being denied by the explicit deny statement, all I can find are 'show acl' commands which just give me the counts.
The equivalent on a router would be debug ip packet acl and adding the log keyword onto an ACE. I suppose I could configure a SPAN session on the WLC uplink to the switch but that seems overkill?
Iam fairly new to Cisco IOS and am having trouble getting an IPSEC tunnel to come up between 2 cisco 881-s. I have entered both debug crypto isakmp and debug crypto verbose but when I try to ping an internal IP at the other location through my VLAN1 interface no debugging info comes up.
Also my ACL-s for the crypto maps show no activity. I have tried many things so my configuration files are starting to get really messy.
[code]...
I'm attempting to debug an ipsec tunnel on an ASA 5510 (8.4(3)) and when I turn on `debug crypto ipsec` and then execute `logging monitor` I get an constant stream of TCP debugging events, is it possible to only view ipsec messages?
View 2 Replies View RelatedDebug is not showing up on the console. I have configured logging console. My older switches, if an interface goes down or is brought up, it shows up on the console, but not on the new 4507s.
WS-C4507R-E
cat4500e-ipbase-mz.122-53.SG2.bin
TG-4507#sh loggingSyslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
[code]....
I'm troubleshooting one way audio with our anyconnect phones.I think it is a routing issue.typically I wouldnt run debug ip packet detail on a production router, however I just found out that you can use acl's to specify the traffic to be debugged.
R1(config)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
R1(config)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
R1(config)#end
R1#debug ip packet 199 detail
IP packet debugging is on (detailed) for access list 199
The use of debug commands requires the allocation of system resources like memory and processing power and in extreme situations can cause a heavily-loaded system to stall. Use debug commands with care. Use an ACL in order to selectively define the traffic that needs to be examined to reduce the impact of the debug command. Such a configuration does not filter any packets.