One of the schools whose networks I administer has a peer to peer network running about 30 xp machines. DHCP is achieved and DNS settings distributed via a basic Linksys router; is there any way of distributing proxy server address and port short of entering manually in LAN settings of IE on every terminal - there is no budget to install a server.
View 4 RepliesI recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies View RelatedI am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies View Relatedi just set up my 2Xp pc's and one windows7 laptop peer to peer for file and printer sharing but i can not configure internet connection for those pc's
View 2 Replies View Relatedi want to set up my two computers /win xp/ installed using peer to peer network , just tell me the needed steps
View 2 Replies View RelatedI bought my WAG320N, I too have the internet drop out and from reading in here is a very common problem. Cisco really should bring out a new firmware version and address this issue. Any way you can block peer to peer file sharing with the WAG320N? If so how do you go about it?
View 1 Replies View RelatedI got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies View RelatedI am facing issues in blocking Peer to Peer applications in LAN. I am using 881 Cisco router and below is the config done. [code]
View 1 Replies View RelatedXYZ Corporation currently employs eight people but plans to hire 10 more in the next four months. Users will work on multiple projects, and only those users assigned to a project should have access to the project files. You’re instructed to set up the network to make it easy to manage and back up. Would you choose a peer-to-peer network, a server-based network, or a combination of both?
View 1 Replies View RelatedI want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies View RelatedWhat is difference between Peer to Peer network and point to point network???
View 5 Replies View RelatedThe setup I currently have is a server attached via an etherchannel to a 3560x switch, which is connected to a pair of 5548UP's that are connected via vpc. The 5548's both have a single connection to 6500 series switch that does the layer 3 routing, the ports that connect the 5548 to the 6504 are trunk ports. The problem that I am having is that one of the 5548's can ping the server that is connected down stream while the other 5548 can't. While the local switch can ping the server, and other servers on the same switch in the same vlan can ping it as well. The vlan interface I am pinging from on each switch is on the same subnet as the server I am trying to ping. One other thing, Nexus #1 which can ping the sever has the mac address in its mac address table, while Nexus #2 doesn't. However I added the static mac entry to Nexus #2 and that did not allow me ping either.
View 2 Replies View RelatedOn a csico 3750 switch I have ntp server < IP of stratum 1 Time Server> I want the swit to sync to the to time server and provide time to peers on my network. Do I have to be configured for ntp peer < IP of stratum 1 Time Server> for that to work?
View 7 Replies View RelatedWhy does Cisco recommend a configuration of originate-only on the ASA with multiple peers configured and the answer-only to the other end? Shouldn't it work as Bi-Directional ?
[URL]
The only scenario I see which could break is if both peers try to establish a VPN at the same time to the ASA. Is there any other reason ?
I've connected my 3 pc's to share file printer and internet using peer to peer connection but on the clients pc the internet connection is soooo slow? my two computers are windows XP an d one Windows7.
View 1 Replies View RelatedI believe that the Cisco Unified Communications Manager Express matches the outbound VoIP dial peer digit-by-digit, because:
1. when using the debug command it shows how it works digit-by-digit till it match a pattern
2. It says in the study guide ( If a match is found, the router immediately processes the call - chapter 6) so I understand its not en bloc
We are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies View RelatedI have a few site-to-site VPNs connecting to my ASA 5520, but one of the remote VPNs is changing it's public IP, how can I change this IP on the ASA without starting again? On the ADSM it is greyed out so I can't edit it, but can I just change it in the CLI?
View 2 Replies View Relatedam in the progess of replacing a Zyxel USG 300 to a Cisoa ASA 5510.In the Zyxel I have some Site to Site, where the peer is a dyndns.org adresse, becourse the peer is a dynamic ip-adress.
I have maybe 10 site to site´s where the peer is a dynamic with a dyndns.org adress, and the presharedkey is diffrent at each tunnel.How can i make this configuration at the ASA 5510?
I have another odd issue (I get those alot) I have an asterisk box that moves around between 2 IPs, thus the dial-peers are unpredictable as to their target IP. They work as the dial-peer will eventually (after 1 min) time out and go to the other dial peer, but waiting 1 min sucks, and it's a tiny network, 5-10 sec would be WAY more than enouph. Does anyone know off hand a way to get them to time out faster?
View 5 Replies View RelatedI have a simple question regarding dead peer detection on the ASA 5520. I am using a cellular VPN device to connect back to an ASA 5520 and I have noticed that the connection drops at random periods during the day. The vendor for the cellular device recommends disabling dead peer detection on their device, which I have done. The question is, where is this disabled on the ASA? is it the IKE Keepalive setting under the tunnel group option?
View 1 Replies View RelatedI'm running a 5505 with DHCP on the outside interface. All 5505 are connecting to 5545.Can I configure the ASA for a site to site to automactically discover the the peer address and automatically establish a connection with 5545?In other words can I configure all settings for the site to site except the peer address. Once connected on network and get outside DHCP, can it also put that address is the peer section of site to site?
View 1 Replies View RelatedI have an ASA 5520 with multiple site-to-site VPN's. A remote customer has changed their Public IP address and now the VPN has gone down. How can I easily change the peer IP of the remote site to the new one without have to put the pre-shared key in again as we don't know what it is and they don't manage their firewall.
View 7 Replies View RelatedI confgured one L2L VPN on my ASA 5505.
How to add another L2L configuration for an additional peer ?
It seems the 7.3.101 version Mobility group peer cannot up,: refer to the attach,
Peer 1: version: 7.3.101
Peer 2: version 7.0.98
Peer3: version 7.2.103
Today we got new two WLC for Anchor use, and config the mobility group, but it's failed and cannot up, the ping is ok.
i still newbie to configure eBGP, i have Router 3600 series, and i configure BGP neighbor to my ISP, but the peer still don't established,there is warning like this, Connections established 339; dropped 339 "Last reset 2w4d, due to Peer closed the session No active TCP connection"
any one can explain to me about "due to Peer closed the session"? i've read some documents for troubleshooting BGP, and do some step to troubleshoot.
We have an HQ site with a 2811 (w/ADVSECURITYK9-M) acting as the firewall. We currently have 1 ASA5505 that has an established ipsec l2l VPN. I'm trying to connect a 2nd ASA, but I've noticed I can only add 1 cryptomap to the outside interface. A show ver shows 1 Virtual Private Network Module... Surely that doesn't mean only 1 VPN?Do I use one crypto map, and add a second 'set peer' & 'match address' inside the crypto map itself?
View 10 Replies View RelatedAny way of narrowing down a degub for a peer address only? For example, I currently run 'debug crypto isakmp 127' which captures everything, but can I run the same dVPN debug for peer address 1.1.1.1?I know you can run 'sh crypto ipsec sa peer 1.1.1.1'.We're using an ASA5520 (8.4.2).
View 2 Replies View RelatedI am unable to VPN to my network from outside using cisco VPN client to PIX-515E. When I try it say: Reason 412: the remote peer is no longer responding. From inside everything work ok, I can connect... (same computer, same settings...)
View 3 Replies View RelatedI have a pair of ACE 4710 and I think I have all the failover configured correctly and it all appears to be working. My question is regarding setting QOS on the physical interfaces that are part of my port channel. I have qos trust cos enabled on all the interfaces in my port channel. These interfaces are connected to a 3750 swith. Do I need to configure QOS on the 3750 to allow the COS bit to pass through my 3750 to my peer?
View 3 Replies View RelatedWhat is the function of the VPC peer-link? Should be the composite of all VPC links that are dual homed between switches? is it necessary to have 8 x 10G links as shown above. The links connecting the 7Ks to the 5Ks are VPC links.
View 3 Replies View RelatedWe are trying to add an additional LAN-to-LAN IPsec VPN to our network. We currently have one remote office connected, when we configure the second VPN matching the first the tunnel never begins to establish. There is an ACL that is dening the static IP for our remote office.
The layout is as follows:
Main office = ASA 5520
Remote Office A = ASA (Unknown Model)
Remote Office B = Adtran Router
All devices have static IP addresses.
We used the ASDM VPN wizard to create both VPN's.
We have created a rule allowing all traffic from our remote office IP, and that had no effect on the VPN aside from eliminating the following message from our logging:
4 Mar 19 2012 15:18:01 106023 67.50.19.230 50234 TWT-hq-e 31326 Deny udp src TWT-outside:67.50.19.230/50234 dst inside:TWT-hq-e/31326 by access-group "outside-in" [0x0, 0x0]
We have verified that both sides are configured the same however the VPN never is initiated so as of right now the ASA is simply blocking all attempts from our remote office to connect.