On a csico 3750 switch I have ntp server < IP of stratum 1 Time Server> I want the swit to sync to the to time server and provide time to peers on my network. Do I have to be configured for ntp peer < IP of stratum 1 Time Server> for that to work?
View 7 Repliessome of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies View RelatedFor intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedThe setup I currently have is a server attached via an etherchannel to a 3560x switch, which is connected to a pair of 5548UP's that are connected via vpc. The 5548's both have a single connection to 6500 series switch that does the layer 3 routing, the ports that connect the 5548 to the 6504 are trunk ports. The problem that I am having is that one of the 5548's can ping the server that is connected down stream while the other 5548 can't. While the local switch can ping the server, and other servers on the same switch in the same vlan can ping it as well. The vlan interface I am pinging from on each switch is on the same subnet as the server I am trying to ping. One other thing, Nexus #1 which can ping the sever has the mac address in its mac address table, while Nexus #2 doesn't. However I added the static mac entry to Nexus #2 and that did not allow me ping either.
View 2 Replies View RelatedI am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies View RelatedI am facing issues in blocking Peer to Peer applications in LAN. I am using 881 Cisco router and below is the config done. [code]
View 1 Replies View RelatedOne of the schools whose networks I administer has a peer to peer network running about 30 xp machines. DHCP is achieved and DNS settings distributed via a basic Linksys router; is there any way of distributing proxy server address and port short of entering manually in LAN settings of IE on every terminal - there is no budget to install a server.
View 4 Replies View RelatedI have a very basic networking question If I have, say, 3750's (or any L3 switch, capable of routing) at the edge and a 4500 at the core, where should I route? At the edge? At the Core? Both?
View 4 Replies View RelatedI have a contained environment where I just want my servers all to have the same time. I want them to pull that time from my 3750. What do I have to enable on the 3750 to be the NTP clock source.
Keep in mind that the 3750 will not be getting the source from anywhere else, just my "set clock" command.
How do i go about setting up a TFTP server from laptop to Cisco ws-C3750 48P Switch, I need to pull the image off the switch and place it on an other switch that has a corrupt image, The switch which is corrupted is the same as above Cisco ws-C3750 48P.
View 1 Replies View RelatedI have customer who has as Core Switch one Cisco Catalyst 3750 with the IOS c3750-ipbase-mz.122-35.SE5.I know that this image support DHCP Server configuration, but I like to implementate new vlans (approx 15) and I want to know if this switch support 15 DHCP Servers.
View 3 Replies View RelatedI am facing a problem in implementing HSRP. My scenario is like this, I have two 3750 switches and I have a server with two NICs. I want to run HSRP in these two switches. By the way the server is connected directly with the switches. I mean each NIC to each switch.we have teamed the two NIC (Active / Standby).what configuration need to done in switches to work HSRP.
View 4 Replies View RelatedServer with Two NIC teamed using HP teaming tool. NIC#1 connects to SW1 and NIC#2 connects to SW2
SW1--------------------NIC_1 (SERVER) NIC_2--------------------SW2
Will the config be access-port on Sw1 & Sw2 connecting to Server.Sw1 & Sw2 are connecting to 3750 as trunk ports
Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
View 9 Replies View RelatedI have an issue on the Cat 3750 on the voice vlan; IP Phone not registering with PBX & Signaling Server. The ip phone hits dhcp and gets an ip address from a data scope. Data scope does have dhcp options for voice, same as voice scope so it should work but it doesnt.We removed the switchport access vlan 50 command, and left the switchport access voice vlan 51, and now the phone registers.Anything I can check on the switch to make sure voice vlan is working? Any debug voice vlan commands?The switch doesnt seem to distinguish voice and data traffic.I check dhcp and both scopes vlan 50 and vlan 51 have the same configuration. Defautl GW is different of course Catalyst 3750 is running 12.2(25)SEE2 [code]
View 5 Replies View RelatedActually i have a design from my customer who have ( Cisco core switch 3750 (allports fiber ports) which is connected to L2 switches , these switches carry servers and end users .the only routing protocol on the access switches is static route ,
My question how can i route the traffic from the server to the end user , as the the server is not direct connect to the core switch.
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
What is the function of the VPC peer-link? Should be the composite of all VPC links that are dual homed between switches? is it necessary to have 8 x 10G links as shown above. The links connecting the 7Ks to the 5Ks are VPC links.
View 3 Replies View Relatedi am in process of building a new datacenter with 2 nexus7k in core/aggregation and 2 n5k in access layer. I am running fabric path on F2 cards between 7k and 5k, also enabled vpc+ on 7k and 5 both. There are few vrfs on 7k which are communicating with each other through firewall contexts. Now there are few vlans which are used to connect differnt vrfs and firewall contexts on n7k and running hsrp as well. now since these vlans are not traversing FP network i should not logically configure these vlans as FP vlans. But since the vpc+ peer link is a FP link it will not allow non-FP vlans to communicate through itself. I have configured a vpc trunk link between 7k and fws. Diag is attched. Now my question is can i configure vlans used for connecting vrf and fw contexts as FP vlans so that hsrp running between those vlans can communicate with each other over vpc+ peer link on n7k.
View 1 Replies View RelatedI have a pair of ACE 4710 and I think I have all the failover configured correctly and it all appears to be working. My question is regarding setting QOS on the physical interfaces that are part of my port channel. I have qos trust cos enabled on all the interfaces in my port channel. These interfaces are connected to a 3750 swith. Do I need to configure QOS on the 3750 to allow the COS bit to pass through my 3750 to my peer?
View 3 Replies View RelatedWe recently had a pair of Nexus 5k switches setup in our network. We had professional services handle the initial configuration but they weren't able to setup config sync for us. Each Fex is connected to each 5k, so we need a switch-profile to maintain a consistent setup on our interfaces. I went through the process in Configuring Switch-Profiles, but when I check the status of the peer, it says not reachable. [code]
View 1 Replies View RelatedCan you use twinax cables to connect two Nexus 7010 switches for VPC peer link? They would connect on F2 modules and have Sup2 on the chassis.
View 2 Replies View RelatedI need to enable vPC "peer-switch" command on a pair of Nexus 7018s which are currently vPC peers (primary and secondary). The STP root and Secondary root are currently configured across these switches.Can I enable the peer-switch command in this configuration without impacting services, and then modify both switches to have the same bridge priority without impacting services ? We have a few downstream 5ks which are not dual homed to both vPC peers (work in progress) so need to understand if the peer-switch command will in any way break this connectivity for now.
View 1 Replies View RelatedI'm trying to create a vpc between a Nexus 5010 and Nexus 5020 switch. I recently upgraded the software so they are running the same version. I connect get a vpc link. Is there something wrong with my setup? Is a vpc between a 5010 and 5020 even possible? They are connected using a pair of Intel X520's in 802.3AD teaming mode. [code]
View 2 Replies View Relatedwe are planing to run HSRP on our Nexus 5ks (with L3 card) and we use VPC to connect the downstream UCS - Fabric Interconnects to the 5ks. I was wondering if the peer-gateway command is required under the vpc domain config? When you use HSRP with VPC, both the active and standby HSRP peers can forward layer3 traffic, isn`t that the same that peer-gateway would achieve?
View 1 Replies View RelatedI own a Cisco 892W router. The router has 2 WAN ports and 8 switch ports. Now I know -
-WAN ports can create sub interfaces, assigne IPs, cannot be assigned to a VLAN - sounds very much like a routing port. (sh interface gives - Hardware is PQII_PRO_UEC)
-Switch ports are for VLAN assignment, trunking, IP assigment etc,. (sh interface gives Hardware is Fast Ethernet)
I know they are different but at the same time confuced what the difference are? I also know on some 3xxx series switchs you could say "no switchport" and translate a switch port to a layer 3 port. But on 892W you can't do this? Struggeling to understand the difference.
What is the difference between the Diameter and the Max Hops Remaining in RSTP/MSTP? Like Cisco, the maximun value for diameter is 7, but, can i have a ring topology with 10 switches in the Network?
View 1 Replies View RelatedI have two sites connected to each other using L2 MPLS/1Gbps "provided by the telecom", the link is configured as a 802.1q trunk and terminated on C3750 on both sites. Everything is working fine according to the below configuration. But i am facing QoS limitations on the number of queues, i checked cisco web site and found that the ME3600/3800 has HQoS which will give me advanced QoS features.I am thinking to migrate from the 3750 to ME3800, but i am new to metro switches. if i can apply the same below configuration on ME3800 except the QoS as i will replace it by MQC configuration? So can I consider that the ME3800 has all 3750 features plus MQC QoS?
!
!!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
[code]....
I currently have Nexus 5596 pair with VPC peer link Po1 between them. My goal is to connect our new Nexus 7Ks to the 5K's using Fabric Path. My question is during this inital setup with the 7K's. Can I use the same port channel number on the 7K's as I did the 5K's? Is the port channel locally significat?
View 2 Replies View Related