I have a contained environment where I just want my servers all to have the same time. I want them to pull that time from my 3750. What do I have to enable on the 3750 to be the NTP clock source.
Keep in mind that the 3750 will not be getting the source from anywhere else, just my "set clock" command.
The question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
I was configuring link aggregation between a Cisco3750 and Cisco SG200 and the switched network went down just a few minutes after the port channel came on.I rebooted the SG200 and all hosts came back up for a minute before I lost them again. The etherchannel was between two trunking ports. I never set link aggregation on the SG200, could that be the reason? All machines are connected to the SG200. The 3750 is only being used as a layer 3 device for inter vlan traffic.
View 1 Replies View RelatedI had to format flash and recover. I did the quicker way by using set BAUD 115200...once the .bin was across I forgot to set the baud back to 9600. I have followed instructions: go back to switch: set BAUD 9600 then reset. also tried the unset command. problem is it always comes back up with a BAUD of 115200. CWill I have to label 1 switch as 115200?
View 38 Replies View RelatedOne of the ports on the 3750 stack was configured for VLAN121. It was changed to VLAN40 and the configuration saved. Both VLANs exist in the switch configuration. As soon as a host was connected (in this case, a label printer) the port VLAN reverted back to VLAN121.
View 3 Replies View RelatedHow do i go about setting up a TFTP server from laptop to Cisco ws-C3750 48P Switch, I need to pull the image off the switch and place it on an other switch that has a corrupt image, The switch which is corrupted is the same as above Cisco ws-C3750 48P.
View 1 Replies View RelatedI have customer who has as Core Switch one Cisco Catalyst 3750 with the IOS c3750-ipbase-mz.122-35.SE5.I know that this image support DHCP Server configuration, but I like to implementate new vlans (approx 15) and I want to know if this switch support 15 DHCP Servers.
View 3 Replies View RelatedOn a csico 3750 switch I have ntp server < IP of stratum 1 Time Server> I want the swit to sync to the to time server and provide time to peers on my network. Do I have to be configured for ntp peer < IP of stratum 1 Time Server> for that to work?
View 7 Replies View RelatedI am facing a problem in implementing HSRP. My scenario is like this, I have two 3750 switches and I have a server with two NICs. I want to run HSRP in these two switches. By the way the server is connected directly with the switches. I mean each NIC to each switch.we have teamed the two NIC (Active / Standby).what configuration need to done in switches to work HSRP.
View 4 Replies View RelatedServer with Two NIC teamed using HP teaming tool. NIC#1 connects to SW1 and NIC#2 connects to SW2
SW1--------------------NIC_1 (SERVER) NIC_2--------------------SW2
Will the config be access-port on Sw1 & Sw2 connecting to Server.Sw1 & Sw2 are connecting to 3750 as trunk ports
Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
View 9 Replies View RelatedI have an issue on the Cat 3750 on the voice vlan; IP Phone not registering with PBX & Signaling Server. The ip phone hits dhcp and gets an ip address from a data scope. Data scope does have dhcp options for voice, same as voice scope so it should work but it doesnt.We removed the switchport access vlan 50 command, and left the switchport access voice vlan 51, and now the phone registers.Anything I can check on the switch to make sure voice vlan is working? Any debug voice vlan commands?The switch doesnt seem to distinguish voice and data traffic.I check dhcp and both scopes vlan 50 and vlan 51 have the same configuration. Defautl GW is different of course Catalyst 3750 is running 12.2(25)SEE2 [code]
View 5 Replies View RelatedActually i have a design from my customer who have ( Cisco core switch 3750 (allports fiber ports) which is connected to L2 switches , these switches carry servers and end users .the only routing protocol on the access switches is static route ,
My question how can i route the traffic from the server to the end user , as the the server is not direct connect to the core switch.
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
I'm setting up a Cisco 3750 layer 3 switch with several vlans. I thought enabling routing would route between the vlans, but no such luck.What I want is to share the internet access of vlan 100 with the other vlans/ip-nets.How can I do that?
View 2 Replies View RelatedDo I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies View RelatedI'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedWe have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
I started using RIPv2 on Packet Tracer. I got two subnets to connect with two routers. After I completed that, I decided to add a third router. How to setup the Routing Table for atleast R3 ?
View 5 Replies View RelatedWe got a layer3 switched network, with one vlan for every switch, routed by a cat4006. [code] So can we put some ports on different switches in, let`s say vlan 50, with different ips? For example, Port 0/3 on Switch 1 and 0/8 on Switch 2, but keeping the ip of the "old" vlan? Or is it necessary to configure a specified vlan interface with ip-adress for every vlan if i want to route it?
View 4 Replies View Relatedsome of our switches have the switchport mode trunk command configured between the 3750 switches but other 3750 switches connected to our 6509 core switch do not have the switchport mode trunk command to permit Vlans from going across the swtiches instead it has an ip address and says no switchport what is the difference between does two. Is trunking used only for Layer 2 and L3 is used to route interface vlans?
View 2 Replies View RelatedI have a network with a Catalyst 3750 as the main switch and then some Catalyst 2960 switches that are plugged in to that. I have a server running windows server 2008 with a couple of virtual machines running in Hyper-V. I created 4 VLANS listed below and gave the 3750 the following IP Address.I would like the 3750 to only be configurable from VLAN 40 but currently every VLAN can connect to it, I noticed in the standard web page settings there was a setting for "Management VLAN" but it was set to 1 and would not let me change it, I kinda assumed that was for the management port in the back.-Now the tricky part, I was trying to set up routing between the VLANs and so far I have only been able to get a sort of "all or nothing" routing to work. I can turn IP routing on and add two or more VLANs to the routing and it works fine. But what I was hoping to do is create a couple of "junction vlans" that would only route to one or two other vlans. For instance, I wanted to create a VLAN 100 that routed to VLAN 20 and 30 but nothing else. I also want to route VLAN 1 just to VLAN 30, and so on. I am able to do each one of the cases but only one, it seems like the switch only supports one "routing table" am I missing something or is this just a limitation of the switch?
View 2 Replies View RelatedIs a 3750 sw capable of handling full routing tables and what can you recommend in a small mutihomed BGP router or switch capable of handling full routing tables?
View 2 Replies View RelatedI have a network with several catalyst 2960 switches and one catalyst 3750. I have created two VLAN and set up the proper routing and everything is working fine there. I have a client/server application that used multicast in the initial start up for the client to determine available servers, the issue is one of my clients is on a different VLAN then the server. I am able to route the multicast using MVR as long as both the server and the client are plugged into the 3750 by creating a static route, making the server a source port and the client a receive port. Unfortunately I need the client and the server plugged in to different 2960s. My question is how do I establish multicast routing between the two and perferably do it dynamically (always route multicast traffic from one VLAN to another).
View 2 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedFor intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies View RelatedI have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies View Related