Cisco VPN :: ASA 5505 DHCP Peer Detection?
Apr 1, 2012
I'm running a 5505 with DHCP on the outside interface. All 5505 are connecting to 5545.Can I configure the ASA for a site to site to automactically discover the the peer address and automatically establish a connection with 5545?In other words can I configure all settings for the site to site except the peer address. Once connected on network and get outside DHCP, can it also put that address is the peer section of site to site?
View 1 Replies
ADVERTISEMENT
Oct 22, 2011
I have a simple question regarding dead peer detection on the ASA 5520. I am using a cellular VPN device to connect back to an ASA 5520 and I have noticed that the connection drops at random periods during the day. The vendor for the cellular device recommends disabling dead peer detection on their device, which I have done. The question is, where is this disabled on the ASA? is it the IKE Keepalive setting under the tunnel group option?
View 1 Replies
View Related
Feb 13, 2011
I confgured one L2L VPN on my ASA 5505.
How to add another L2L configuration for an additional peer ?
View 4 Replies
View Related
Mar 5, 2013
I've been using an ASA 5505 -- ASA 9.1(1) -- with an IPSec Remote Access VPN. Everything works properly, though I recently noticed that when my IPSec session is disconnected, I get the standard message ID 113019, but within that message the Peer IP address is incorrect. In fact, it isn't even close to my actual remote address. [code]
When I first researched the IP, I found it coming from China, which freaked me out. I changed settings, rolled back to 9.0(1), and nothing worked. Finally I rebooted, reconnected the VPN, and the IP changed. This time it was an address from RIPE NIC. I rebooted again, now an address from ARIN in the USA. One more reboot, now a random Comcast residential address.
Within that boot cycle, the peer address always stays the same. I've connected from different devices, different IPs, different ISPs - nothing matters. Additionally, there are no firewall logs for these IP addresses at all.
ASA Remote Access VPN peer addresses in disconnect message are incorrect and change at reboot.
View 3 Replies
View Related
Feb 25, 2013
I am working on wi-fi networks (ISP), So I need to block the peer to peer on my network.My network involves cisco switch 2950/2960, cisco 2800 routers and Access Points, config for peer to peer blocking, for this where I need to config either switches or router.My network basic setup is, The internet will pass from router to switch and then Access Points.
View 1 Replies
View Related
Apr 19, 2012
I got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
View 3 Replies
View Related
Jul 25, 2011
I see that Application protection - blocking peer-to-peer file sharing traffic is a capability of Cisco IOS Firewall. How do i configure my Cisco 2911 ISR to block peer-to-peer file sharing traffic?
View 1 Replies
View Related
Feb 13, 2013
I am facing issues in blocking Peer to Peer applications in LAN. I am using 881 Cisco router and below is the config done. [code]
View 1 Replies
View Related
Jul 31, 2011
I recently bought the WAG320N can I block Peer to Peer file sharing on my Network?
View 3 Replies
View Related
Jul 31, 2011
I bought my WAG320N, I too have the internet drop out and from reading in here is a very common problem. Cisco really should bring out a new firmware version and address this issue. Any way you can block peer to peer file sharing with the WAG320N? If so how do you go about it?
View 1 Replies
View Related
Jan 28, 2011
One of the schools whose networks I administer has a peer to peer network running about 30 xp machines. DHCP is achieved and DNS settings distributed via a basic Linksys router; is there any way of distributing proxy server address and port short of entering manually in LAN settings of IE on every terminal - there is no budget to install a server.
View 4 Replies
View Related
Jan 18, 2011
i just set up my 2Xp pc's and one windows7 laptop peer to peer for file and printer sharing but i can not configure internet connection for those pc's
View 2 Replies
View Related
Mar 12, 2011
i want to set up my two computers /win xp/ installed using peer to peer network , just tell me the needed steps
View 2 Replies
View Related
Mar 13, 2011
I have 2 ASA 5505 Firewall, I Configured Site 2 Site VPN no both the fitrewall, as i have a dual ISP, i am able to create the tunnel with primary but once my primary is down i am not able to create the tunnel with back up ISP. During the troobleshoothing by typing Show isakmp sa and Show ipsec sa, i can see my tunnel is up, but not able to decap the packets.
As it will look like
#pkts encaps: 15, #pkts encrypt: 15, #pkts digest: 15 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 15, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0
View 4 Replies
View Related
Jan 24, 2013
I want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies
View Related
Feb 21, 2010
I have an ASA 5505 configured to get a DHCP'd IP address from the ISP on it's outside interface. The problem I am seeing is when the ISP renews their IP address, the ASA 5505 is still holding on to the old IP address information. I have to either manually renew the IP or reload the ASA. I have the potential of rolling out hundreds of these devices and I would not like my customers to have to reboot their ASA everytime the ISP's DHCP lease experies. I am using an easy vpn autoconnecting to an ASA 5520. Static IP's are not an option on the outside interface of the ASA 5505's.
View 8 Replies
View Related
May 10, 2012
I'm using an ASA5505 with dhcpd.but i want to assign a specific IP address from the configured dhcp range to a specific PC.Is it possible to bind a specific ip to this particular PC's MAC address.
View 1 Replies
View Related
Apr 14, 2013
I've got a 5505 and I'm getting a DHCP address from a cable modem. How can I show the DNS that the ASA is getting? show int vlan 2 is only givving me the IP and net mask.
View 2 Replies
View Related
May 13, 2012
We recently upgraded our 5505s to 8.2(5) 26 and noticed that each will crash after a cerntain amount of time. Some crash every 30 minutes other will crash every 4 to 8 hrs. The only difference would be the user's home ISP and/or home router, if they have one. They are configured with a dynamic dhcp IP address for the outside interface and the crash files starts with the following:When we downgrade back to 8.2(5) 13 the problem goes away. Any known bugs for this version? I haven't been able to find anything yet. We do have one 5505 that does not have this issues. The only thing that may be different is that it was never at 8.2(5) 13. We had downgrade it from a 8.3 version.
View 2 Replies
View Related
May 17, 2013
Well its in this line but do i have to type in a ip even if comcast is giving me a dhcp address?
route outside 0.0.0.0 0.0.0.0 any 1
=============================
hostname asa1
domain-name mydomain.com
enable password rwt5UQJihEq2/Qae encrypted
names
!
interface Vlan1
[code].....
View 4 Replies
View Related
Dec 4, 2011
I am opening a small branch office in another state and the equipment we purchased is as follows:
ASA5505
3560G.
We'll use a site to site vpn but just in case there's connectivity issues I'd like to use the ASA as DHCP. So far I have a scope defined in the ASA and if I plug a laptop directly in I get an applicable IP address. I trunked the port on the switch that goes to the ASA but not the one on the ASA itself (license restriction) The VLAN that I'm using for my PC's has an ip helper address that is assigned to the inside IP of the ASA.
View 5 Replies
View Related
Nov 21, 2011
I've been running a cisco asa 5505 for quite some time and it has been running fine, now all of a sudden it starts to renew it's outside dhcp adress like every 2 hours. I dont think it's the ISP since I have another device connected also using dhcp to the same ISP and it doesnt renew itself, it's just the ASA. Rebooting it, makes it pick up an adress straight away. The interface seems to be up, the GUI just reports "no ip adress" and then the ASA get's a new IP after about 10-15 min without one. Pressing the renew IP adress button in the GUI throws an error.
View 10 Replies
View Related
Dec 23, 2011
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
View 5 Replies
View Related
Jan 25, 2011
I've been having this issue for about 3 months now, off and on, never seemed to be predictable but started happening more and more, which prompted me to look into it.
Currently, the DSL Modem is configured in bridge mode with the ASA handling PPPoE. The WAN address is being assigned via DHCP. The ASA is running 8.2(1). The WAN interface will drop it's DHCP lease and will not renew it without power cycling the DSL modem. I did a little bit of googling and found mention of setting "dhcp-client client-id interface outside", specifically this was an issue pre 7.2(22), but doesn't seem to affect my situation. Originally, I had the MTU on the outside interface configured as 1500, changing it to 1492 has not resolved my issue either.
I've enabled PPPoE and DHCPC debugging and posted the results below when the event occurs, I'm thinking this is moreso a PPPoE issue than it is a DHCP/DHCP Lease issue as I am not seeing any debug messages from DHCPC.
Code...
View 1 Replies
View Related
Nov 17, 2011
Our company is planning to buy one of cisco ASA 55xx series.But there is still one question left about DHCP pool limitations.Here I found some information about licensing for DHCP on ASA 5505: [URL]In other words, we don't have any information about ASA 5510, which contains DCHP pool licensing.
View 9 Replies
View Related
Nov 1, 2012
I get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
View 14 Replies
View Related
Jun 18, 2012
i have ASA 5505 and have a ADSL modem (hwich has DHCP enabled) 192.168.1.X/24....i have static ip as well which is 34.X.X.X. i want to use ASA as a firewall and want to make site to site VPN..i tried to google it but i cant find any config.i have 4 swicth port in the ADSL modem so shd i connect my ASA with building switch but then it will have DHCP enabled if i disable DHCP on ADSL router then how will my ASA communicate.
View 1 Replies
View Related
Jun 28, 2011
I found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. Any configuration i missed in firewall?
View 5 Replies
View Related
Apr 16, 2013
my 5505 running on version 8.2.5 doesn't seem to recogize the simple command "ip address dhcp setroute......"
ciscoasa(config-if)# ip address dhcp
^
ERROR: % Invalid Hostname
ciscoasa(config-if)# ip address ?
configure mode commands/options: Hostname or A.B.C.D Firewall's network interface address
View 7 Replies
View Related
Mar 12, 2011
I have a ASA 5505 that I have been using for a while, but a new ISP is trying to configure my service so that the outside interface has to be configured as DHCP to receive a reserved IP address, and then they will route a separate, non-contiguous block of addresses to that address.
Essentially, they have a DHCP reservation for 1.2.3.4 for my ASA, and then they have 10.2.3.16/28 as a separate block routed to me.
Obviously, I can do my static NAT translations using outside as the address, but I cannot get the separate block of addresses to route through the ASA. Is there a way to do this and get them to work? My ASA is running 7.2(2)
View 3 Replies
View Related
Oct 4, 2012
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
View 4 Replies
View Related
Jun 26, 2011
I have an ASA 5505 with software version 8.2(1). It is making DHCP requests for IPSec clients that connect to the ASA. The DHCP requests packets the ASA makes have an extra '00' appended to the hostname field, and the length field is the size of the hostname + 1. The DHCP server is Microsoft Server 2003 and this causes the hostname to be registered with an unknown character which appears as []hostname. Then when server 2003 tries to update the DNS record, it fails because of the invalid character in the hostname. Is there anyway to have the ASA have the correct length for the hostname field in the DHCP packet, or a workaround that will solve this problem?
View 5 Replies
View Related
Nov 14, 2011
So here's what I think I should do to give email access only to a segment of addresses of my inside network.
1) Create a network object for 62 machines that will represent my dhcp clients.I plan to use 192.168.0.65-192.168.0.126. So I will use address 192.168.0.64 with netmask 255.255.255.192. Then set DHCP server to service this address range.
2) Create an ACL which will Permit Any to use tcp port 110 (pop3) to get to the outside. Which leads me to question #1:
How do I permit the source "Any" to communicate with "Any Less Secure Networks" like the implicit rule that gets zapped once I create new ACL? Is "Any Less Secure Network" implied by the "Any" destination?
3) Create an ACL which will Deny my DHCP range to talk to the outside.
4) Create an ACL which will Permit Any to talk to Any Less Secure Network(essentially recreating the implicit Permit ACL that got zapped).
View 1 Replies
View Related
