Our company is planning to buy one of cisco ASA 55xx series.But there is still one question left about DHCP pool limitations.Here I found some information about licensing for DHCP on ASA 5505: [URL]In other words, we don't have any information about ASA 5510, which contains DCHP pool licensing.
View 9 RepliesI have a ASA5505 that i have running asdm 6.4 on it and have tried setting up some DHCP scopes for the interfaces.I have the security plus key.I set up 4 interfaces all with different subnets and all with different DHCP being doled out by the firewall for the time being.Anyway, 3 of the 4 work.I have tried to change interfaces wondering if there was an issue with that phy device.I tried enableing the subnet that would not work first and it didnt matter still would not issue dhcp.the other 3 work fine.Is there a limitation to the amount of scopes that will issue dhcp for an asa5505 ?
View 3 Replies View RelatedI'm using an ASA5505 with dhcpd.but i want to assign a specific IP address from the configured dhcp range to a specific PC.Is it possible to bind a specific ip to this particular PC's MAC address.
View 1 Replies View RelatedWe were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedIs it possible to set up DHCP server with reservations for specific IPs?
View 1 Replies View RelatedWell its in this line but do i have to type in a ip even if comcast is giving me a dhcp address?
route outside 0.0.0.0 0.0.0.0 any 1
=============================
hostname asa1
domain-name mydomain.com
enable password rwt5UQJihEq2/Qae encrypted
names
!
interface Vlan1
[code].....
I am opening a small branch office in another state and the equipment we purchased is as follows:
ASA5505
3560G.
We'll use a site to site vpn but just in case there's connectivity issues I'd like to use the ASA as DHCP. So far I have a scope defined in the ASA and if I plug a laptop directly in I get an applicable IP address. I trunked the port on the switch that goes to the ASA but not the one on the ASA itself (license restriction) The VLAN that I'm using for my PC's has an ip helper address that is assigned to the inside IP of the ASA.
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
I get the following message when appling "DHCPD ENABLE INSIDE"
DHCP: Interface 'INSIDE' is currently configured as CLIENT and cannot be changed to a SERVER by a SERVER feature
This is an ASA 5505 Running 8.2.
I found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. Any configuration i missed in firewall?
View 5 Replies View RelatedI'd like to create dhcp server pool on ASA 5510. I was wondering how big is the DHCP scope that Cisco ASA 5510 can support? Are there any ASA models which can support up to subnet mask 22 for DHCP scope?
View 7 Replies View Relatedmy 5505 running on version 8.2.5 doesn't seem to recogize the simple command "ip address dhcp setroute......"
ciscoasa(config-if)# ip address dhcp
^
ERROR: % Invalid Hostname
ciscoasa(config-if)# ip address ?
configure mode commands/options: Hostname or A.B.C.D Firewall's network interface address
I have a ASA 5505 that I have been using for a while, but a new ISP is trying to configure my service so that the outside interface has to be configured as DHCP to receive a reserved IP address, and then they will route a separate, non-contiguous block of addresses to that address.
Essentially, they have a DHCP reservation for 1.2.3.4 for my ASA, and then they have 10.2.3.16/28 as a separate block routed to me.
Obviously, I can do my static NAT translations using outside as the address, but I cannot get the separate block of addresses to route through the ASA. Is there a way to do this and get them to work? My ASA is running 7.2(2)
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
So here's what I think I should do to give email access only to a segment of addresses of my inside network.
1) Create a network object for 62 machines that will represent my dhcp clients.I plan to use 192.168.0.65-192.168.0.126. So I will use address 192.168.0.64 with netmask 255.255.255.192. Then set DHCP server to service this address range.
2) Create an ACL which will Permit Any to use tcp port 110 (pop3) to get to the outside. Which leads me to question #1:
How do I permit the source "Any" to communicate with "Any Less Secure Networks" like the implicit rule that gets zapped once I create new ACL? Is "Any Less Secure Network" implied by the "Any" destination?
3) Create an ACL which will Deny my DHCP range to talk to the outside.
4) Create an ACL which will Permit Any to talk to Any Less Secure Network(essentially recreating the implicit Permit ACL that got zapped).
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
Is there any way of showing the currently assigned ip address for an interface configured to use DHCP on an ASA 5505?
View 2 Replies View RelatedWe've just started with the ASA 5505. We do run a DHCP server on the inside interface, so it is in the same VLAN 1 as all of the clients. However, we cannot get it to work.We can't use DHCP Relay, as the ASA 5505 only allows to relay to DHCP servers in a different subnet.Or do we have to move the DHCP server to a different subnet. If so, how would we configure that scenario?
View 13 Replies View RelatedI am having a very strange issue with connecting new machines to reach the internet.We have a ASA 5505 which the previous tech configured the DHCP pool to 192.168.1.60 - 192.168.1.110
We ended up reaching our limit which I changed it to: 192.168.1.60 - 192.168.187
Then next day when I arrived to work, our DC was hung from windows updates. Once we got everything back up, every computer currently on the network can reach the internet/VPN tunnels etc. So (continuing with my day) I created a new server in a VM (Hyper-V)I can ping everything internally (even the router) 192.168.1.1, but I cannot resolve DNS. I have configured a static IP, tried Dynamic IP.I have looked for any ACL indicating to block outside the range of the old DHCP pool but no luck.On my local maching I can ping the DNS addresses, but just not on the new server.
My ASA 5505 has stopped giving out DHCP address to my machines.Everything was working fine and nothing has changed in the network. I've reloaded the firewall and clear all DHCP on the firewall I've even re-entered the cmd on the ASA.
I'm able to staticlly assigned address to the clients and all is way. When I do a DHCP debug on the ASA I don't see any events relating to the DHCP service apart from checking for lease expiry.
I've also tried to plug a machine straight into the ASA and no result. I finally did a packet capture and I am seeing the client machine sending out a DHCP discover packet and nothing else is responding.
My ASA config is:
dhcpd address 192.168.3.10-192.168.3.33 inside
dhcpd dns 8.8.4.4 interface inside
dhcpd option 3 ip 192.168.3.1 interface inside
dhcpd enable inside
I´m looking for a firewall for my company and am reading about both Cisco ASA 5505 with Security Plus bundle and Cisco ASA 5510 with Security Plus bundle and I have a few questions.This is the document i´m getting my information from.URL,It states the following:Cisco ASA 5505 Security Plus bundle,Includes Cisco ASA 5505, unlimited users, 8-port Fast Ethernet switch, stateful firewall, 25 IPsec VPN peers, 2 SSL VPN peers, stateless Active/Standby high availability, dual ISP support, DMZ support, 3DES/AES license, and 1 expansion slot.
View 5 Replies View RelatedI am trying to find out the best path to upgrade to two ASA 5510 running 9.0 (1). I know there are changes in the new version. Let me know what information you need and i will post.
View 2 Replies View RelatedWe have a ASA 5505 and a 5510, that we are using site to site..I need to traceroute from the 5505-5510.. From the outside interfaces.. Don't want to do this through the site-to-site.I have temporarily added a few acl on the outside interfaces..
-access-list outside_in extended permit icmp any any unreachable
-access-list outside_in extended permit icmp any any time-exceeded
-access-list outside_in extended permit icmp any any echo-reply
when i traceroute it only goes one hop.. Maybe thats the way it suppose to be? I need to know all the hops between the outside interfaces on the 5505 to the outside interface on the 5510.
I am absolutely new in the enterprise firewall world but I would like to start learning how to configure ASA 5505 and 5510. I did some research myself and I found that the material or the topic itself is a huge adventure (lots to read and understand). My company uses IOS versions until 8.2 due to the differences in the NAT-ting rules with 8.3 and 8.4.
View 1 Replies View RelatedI currently use MS ISA Server 2006 to protect a windows internal network, where there is also an MS Exchange server. I have acquired a Cisco 5510 to enhance security at main office. Later I will have ASA 5505 for branches, including VPN-ning. to have firewall at main office. I have several public IPs and would like to setup DMZ for Web, Exchange server and FTP. How do I setup interface and sub-interface for the DMZ?Can I continue using ISA Server connecting to Cisco 5510 on the perimeter? If so, How do I set the interfaces (and sub-interfaces) as well as NAT-ting and access configuration between the inside and outside?
View 12 Replies View RelatedI have a customer moving from a 5505 to a 5510. They are currently running websense express, which monitors and filters traffic based off of a port mirror on the ASA. Can this function still be performed on the ASA5510? If so, I am having trouble figuring out the method.
View 6 Replies View RelatedCisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
Is there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
View 4 Replies View RelatedWe have a ASA 5505 and a 5510, that we are using site to site.I need to traceroute from the 5505-5510.. From the outside interfaces.. Don't want to do this through the site-to-site.I have temporarily added a few acl on the outside interfaces.when i traceroute it only goes one hop.. Maybe thats the way it suppose to be? I need to know all the hops between the outside interfaces on the 5505 to the outside interface on the 5510.
View 12 Replies View Relatedis it possible to configure a webfiltering on ASA 5505,5510,5520 ? So if its possible can you provide us a configuartion template.
View 3 Replies View RelatedI came across this site. I wanted to produce a better incoming ACL at home and work to prevent known bad sites
Here is their list of the Top 10 Global Spammers is out. The biggest surprise on the list is Korea, as it takes over the number one global spammer spot from China. With the improved high speed internet infrastructure in Korea and ease of network access, who knew Korea would be on the rise.
Here is the complete Global Spanner Top Ten List for the first quarter
[URL]
Korea
China
India
Russia
Turkey
Viet Nam
Ukraine
Brazil
Venezuela
Pakistan
When I sort the list, it is over 16k lines of ACL!
My question relates to what performance limits I would find.
Can I actually put that many lines in an ACL?
Will the router choke and do any other work
I have attached the sorted ACL list for you to review
Any of the following router lines will accept a list that large and still run acceptably?
2811
2911
3925
2945
I have an ASA-5510 in a location that loses connectivity to the wan gateway after anywhere from five to fifteen minutes. At first I thought that the unit might be defective, but I replaced it with an ASA-5505 with similar results. A reload of the ASA-5510 will restore connectivity for the next quarter hour.
Here's the version information on the 5510:
Cisco Adaptive Security Appliance Software Version 8.2(1)
Device Manager Version 6.2(1)
Compiled on Tue 05-May-09 22:45 by builders
[Code].....
A bit of a straight forward question, is it possible to connect a 5505 to a 5510 direct via a crossover or do you need a switch inbetween capable of trunking?
View 1 Replies View Related