Cisco Firewall :: Trace Route Between Two ASA 5505 And 5510
Oct 15, 2012
We have a ASA 5505 and a 5510, that we are using site to site.I need to traceroute from the 5505-5510.. From the outside interfaces.. Don't want to do this through the site-to-site.I have temporarily added a few acl on the outside interfaces.when i traceroute it only goes one hop.. Maybe thats the way it suppose to be? I need to know all the hops between the outside interfaces on the 5505 to the outside interface on the 5510.
View 12 Replies
ADVERTISEMENT
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Jun 10, 2013
I changed from a Linksys E4200 to a 5505 and when I use trace route, it doesn't return a DNS name for each hop. I can see the hops shown as asterisks. Do I have to add something to inspect for this to work?
View 1 Replies
View Related
Jun 6, 2011
I have problem with icmp traceroute configuration. When I enabling icmp error inspection in global policy, my traceroute results through ASA 8.2.4 looks like this: My traceroute [v0.75]
icmp inspection and ttl decrement on ASA is enabled. Also I configured ACL on outside interface to permit ICMP completely.
View 14 Replies
View Related
Dec 29, 2011
I want to know the return path between my IP and a server. I know that trace route gets some information about the hops from my IP to a server (for example www.google.com) but this info is about the forward path. But I want to know what is the path from the server to my PC, what is the reverse path (return path)? What are the middle hops? In other word, I want to know where is the forward and reverse path when I ping a server? I can find the forward path using trace route, but what about the return path?
View 7 Replies
View Related
May 7, 2012
I am trying to track down a device that's blocking a certain port I know there are programs out there than will do a trace-route that's on TCP but is there any programs that allow you to specify a port?
View 6 Replies
View Related
Jul 19, 2012
Have win7 system, cisco WIRED 1720 router, ~1.5mb frame relay via C&WPanama, nortons antivirus installed. IP config dump is at the bottom, but in this event, I don't think my problem is local.An important work-related chat quit working today, and I have narrowed down the issue to not being able to connect to the provider website from my current location. (I can connect via US proxy, but cannot run the java applet via the proxy, it seems it is still trying to go from here to there).
The site I am trying to reach is host7.parachat.com, IP 64.13.158.24
I can load this page (just a landing page comment) as well as their main pages via us proxy, but time out trying to load directly. Fiddler returns a 502 error, socket connection failed.
have tested on 3 machines (all on same router), then on a laptop which hadn't been booted or updated in over a year (also on same router). Trying to find a free wireless network to test with the laptop, but that hasn't been found yet.
[code]....
View 3 Replies
View Related
Mar 24, 2013
when i make a trace route on an ASR 1001 router to 172.23.30.7 I get the following output:
VRF info: (vrf in name/id, vrf out name/id)
1 192.168.99.192 0 msec
192.168.99.191 1 msec
192.168.99.192 0 msec
2 172.23.30.243 1 msec 1 msec 1 msec
3 172.23.30.7 1 msec 1 msec 1 msec
Is there a loop between 192.168.99.191 and .192 (this are two routers with hsrp .190) or is this normal behavior when using trace route on an asr 1001?
View 2 Replies
View Related
Jan 21, 2013
I have an E4200 and have added it to my network with a new static IP and DHCP and firewalls off.It runs off my cable modem and router (Virgin Media Superhub) that has DHCP.When I tell it to do a firmware update, traceroute or ping it fails, just wont do any of them.
View 9 Replies
View Related
Sep 14, 2011
I would like to route traffic that are coming in and going out to the same interface on ASA. I am using inside interface with security-level 100. In this URL, [URL], ASA is able to do that.
View 5 Replies
View Related
Nov 15, 2011
I have configured a remote access VPN on my Firewall ASA5510. Everything worked fine and I can successfully connect through the VPN. The problem is I cannot ping or connect to any of my internal network resources. I tried to add a new NAT route from outside to my internal servers using the defined pool but due to a new ASA version there are many changed I see in the NAT routes
View 37 Replies
View Related
Oct 22, 2012
We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked options is enabled for monitoring the state of the primary route. the detail parameters regarding options as below,
Frequency: 30 seconds Data Size: 28 bytes
Threshold: 3000 milliseconds Tos: 0
Time out: 3000 milliseconds Number of Packets: 8
[code]....
I'm not sure if the setting is so sensitive that the secondary static route begins to work right away, even when some small link flappings occur. What is the best practice to set those parameters up in the production environment. How can we specify the reasonanble monitoring options to fit our needs.
View 5 Replies
View Related
Jan 7, 2013
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
View 2 Replies
View Related
May 30, 2011
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
View 10 Replies
View Related
Jul 21, 2011
In the restructuration of my company network we install due ASA 5510 in failover for the management of internal network and DMZ. We configure the ASA in routed mode, we create the sub interface for server, client and dmz subnet and we connect the firewall ti the network. Everything works very good except the intervlan routin. If i try to send or receive a file in every protocol, ftp, http, smb o if i try to conne with rdp or vns to an host in a different vlan the connection goes very very slow. I particular a ftp connection between two host goes ti 15kb/s. I check all cable and port for some error on duplex ro speed, end all the uplink are 1gb and the single client connection 100Mb. I know that the main purpose of the ASA is not doing routing stuff but this behavior is very strange.
View 1 Replies
View Related
Sep 21, 2011
Is it possible to assign a static route to an interface and not globally on a ASA 5510 ver 8.3.
I have two links between my offices one for Data via a VPN and one for video traffic which is a secure connection with QOS end to end.
All interfaces are on the same security level of 100 except Outside which is 0.
Office 1 Interfaces ASA 5510
VLAN 1 vOffice1Data 10.40.1.0/24
VLAN 3 vOffice1Video 10.40.2.0/24
VLAN 5 vInterOffice 10.40.5.0/24 (QOS connection Between Offices)
[Code]....
At the moment if I try and access data from VLAN 1 to VLAN 4 it gets to the destination ok going through the static route and over the vInterOffice connection but the problem is VLAN 4 returning the traffic. This fails because there is no static route back to VLAN 1. If I create a static route from Office 2 to VLAN 1 then it will route all my data traffic over it as well.
View 2 Replies
View Related
May 15, 2013
I am trying to set up my ASA5510 the fail over of ISP when it can't ping three different IP. I create three different tracking to three different IP using sla monitor & track rtr. But when I do
route isp2 0 0 yy.yy.yy.yy 50
route isp1 0 0 xx.xx.xx.xx 31 track 1
route isp1 0 0 xx.xx.xx.xx 32 track 2
route isp1 0 0 xx.xx.xx.xx 33 track 3
the last route will replace the previous two and only the last route command takes effect.Is there anyway I can set up the fail over to ISP2 only when it can't ping three different IP from ISP1?
View 1 Replies
View Related
Mar 3, 2013
I recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network. There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well. Internet setup was cake. The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks. I have one MPLS with AT&T and one MPLS with EarthLink. My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS. I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
Here's the topology I'm working with
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23
[Code].....
View 8 Replies
View Related
Jul 25, 2011
I have purchased a subnet of 8 private IP addresses from my ISP. 109.x.x.128/29.The ISP has placed a juniper router within our data centre which is routing purely from 109.x.x.206/30 to 109.x.x.128/29 with the ip of fa0/1 set to .129.
I have linked a cisco 5505 to fa0/1 of the juniper from fa0/0 and configured its IP to .130. I have configured NAT to translate our client pool 192.168.16.x /24 address' to the internet.
Is it possible for the 5505 to route / map my remaing private IP addresses through its external port? I have tried creating a seperate VLAN for a DMZ for our servers to sit within but am returned with a subnetting error as VLAN for my external port is all ready configured within the same subnet.
View 2 Replies
View Related
Aug 12, 2012
I am having touble with a NAT concept. What I have is a 3rd party software VPN product that basically tunnels encapsulated traffic to/from a server sitting inside the network. Right now this traffic utiluizes a physical interface on the ASA5510, but I need the interface for another project.
What I have is this:
Internet<----->ASA<-->router<-->4507(layer3)
| |
| |-Vlan1
[Code]......
View 1 Replies
View Related
Apr 24, 2012
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies
View Related
May 22, 2011
I´m looking for a firewall for my company and am reading about both Cisco ASA 5505 with Security Plus bundle and Cisco ASA 5510 with Security Plus bundle and I have a few questions.This is the document i´m getting my information from.URL,It states the following:Cisco ASA 5505 Security Plus bundle,Includes Cisco ASA 5505, unlimited users, 8-port Fast Ethernet switch, stateful firewall, 25 IPsec VPN peers, 2 SSL VPN peers, stateless Active/Standby high availability, dual ISP support, DMZ support, 3DES/AES license, and 1 expansion slot.
View 5 Replies
View Related
Jan 24, 2013
I am trying to find out the best path to upgrade to two ASA 5510 running 9.0 (1). I know there are changes in the new version. Let me know what information you need and i will post.
View 2 Replies
View Related
Oct 15, 2012
We have a ASA 5505 and a 5510, that we are using site to site..I need to traceroute from the 5505-5510.. From the outside interfaces.. Don't want to do this through the site-to-site.I have temporarily added a few acl on the outside interfaces..
-access-list outside_in extended permit icmp any any unreachable
-access-list outside_in extended permit icmp any any time-exceeded
-access-list outside_in extended permit icmp any any echo-reply
when i traceroute it only goes one hop.. Maybe thats the way it suppose to be? I need to know all the hops between the outside interfaces on the 5505 to the outside interface on the 5510.
View 1 Replies
View Related
Mar 18, 2012
I am absolutely new in the enterprise firewall world but I would like to start learning how to configure ASA 5505 and 5510. I did some research myself and I found that the material or the topic itself is a huge adventure (lots to read and understand). My company uses IOS versions until 8.2 due to the differences in the NAT-ting rules with 8.3 and 8.4.
View 1 Replies
View Related
Aug 16, 2010
I currently use MS ISA Server 2006 to protect a windows internal network, where there is also an MS Exchange server. I have acquired a Cisco 5510 to enhance security at main office. Later I will have ASA 5505 for branches, including VPN-ning. to have firewall at main office. I have several public IPs and would like to setup DMZ for Web, Exchange server and FTP. How do I setup interface and sub-interface for the DMZ?Can I continue using ISA Server connecting to Cisco 5510 on the perimeter? If so, How do I set the interfaces (and sub-interfaces) as well as NAT-ting and access configuration between the inside and outside?
View 12 Replies
View Related
Mar 6, 2011
I have a customer moving from a 5505 to a 5510. They are currently running websense express, which monitors and filters traffic based off of a port mirror on the ASA. Can this function still be performed on the ASA5510? If so, I am having trouble figuring out the method.
View 6 Replies
View Related
Dec 19, 2012
I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.
View 1 Replies
View Related
Oct 19, 2011
Is there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?
View 4 Replies
View Related
Nov 17, 2011
Our company is planning to buy one of cisco ASA 55xx series.But there is still one question left about DHCP pool limitations.Here I found some information about licensing for DHCP on ASA 5505: [URL]In other words, we don't have any information about ASA 5510, which contains DCHP pool licensing.
View 9 Replies
View Related
Feb 12, 2013
is it possible to configure a webfiltering on ASA 5505,5510,5520 ? So if its possible can you provide us a configuartion template.
View 3 Replies
View Related
Dec 16, 2012
Our Firewall is just new. ASA5525X
Today, during a packet_trace to debug a routing problem, the active ASA
- thsasaprd02 - crashed suddenly.
I was able to copy-paste the console - including the command that triggered it - After the reboot I ran the command again, on the same ASA - after doing a manual failover - the command succeeded normally.
View 2 Replies
View Related
Jun 23, 2011
I have an ASA-5510 in a location that loses connectivity to the wan gateway after anywhere from five to fifteen minutes. At first I thought that the unit might be defective, but I replaced it with an ASA-5505 with similar results. A reload of the ASA-5510 will restore connectivity for the next quarter hour.
Here's the version information on the 5510:
Cisco Adaptive Security Appliance Software Version 8.2(1)
Device Manager Version 6.2(1)
Compiled on Tue 05-May-09 22:45 by builders
[Code].....
View 1 Replies
View Related
