Cisco Firewall :: ASA 5505 Route Monitoring Options?
Oct 22, 2012
We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked options is enabled for monitoring the state of the primary route. the detail parameters regarding options as below,
Frequency: 30 seconds Data Size: 28 bytes
Threshold: 3000 milliseconds Tos: 0
Time out: 3000 milliseconds Number of Packets: 8
[code]....
I'm not sure if the setting is so sensitive that the secondary static route begins to work right away, even when some small link flappings occur. What is the best practice to set those parameters up in the production environment. How can we specify the reasonanble monitoring options to fit our needs.
View 5 Replies
ADVERTISEMENT
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Jul 25, 2011
I have a question regarding failover monitoring on the ASA5505 in an active/standby configuration.
I understand that on the 5505 you create VLAN interfaces and then assign the VLANs to the 5505 switchports. With failover configured on the 5505, the VLAN interface names are monitored. For example, VLAN 100 interface named Inside is assigned to ethernet0/1, switchport mode access. When issuing a show failover command the output will show the monitor status of interface Inside..
Does failover monitor the VLAN virtual interface only? Does failover also monitor the link status of the ethernet0/1 switchport?
View 1 Replies
View Related
Mar 27, 2008
I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
View 2 Replies
View Related
Jan 7, 2013
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
View 2 Replies
View Related
Oct 15, 2012
We have a ASA 5505 and a 5510, that we are using site to site.I need to traceroute from the 5505-5510.. From the outside interfaces.. Don't want to do this through the site-to-site.I have temporarily added a few acl on the outside interfaces.when i traceroute it only goes one hop.. Maybe thats the way it suppose to be? I need to know all the hops between the outside interfaces on the 5505 to the outside interface on the 5510.
View 12 Replies
View Related
May 30, 2011
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
View 10 Replies
View Related
Jul 25, 2011
I have purchased a subnet of 8 private IP addresses from my ISP. 109.x.x.128/29.The ISP has placed a juniper router within our data centre which is routing purely from 109.x.x.206/30 to 109.x.x.128/29 with the ip of fa0/1 set to .129.
I have linked a cisco 5505 to fa0/1 of the juniper from fa0/0 and configured its IP to .130. I have configured NAT to translate our client pool 192.168.16.x /24 address' to the internet.
Is it possible for the 5505 to route / map my remaing private IP addresses through its external port? I have tried creating a seperate VLAN for a DMZ for our servers to sit within but am returned with a subnetting error as VLAN for my external port is all ready configured within the same subnet.
View 2 Replies
View Related
Jan 31, 2012
I recently upgraded an ASA 5505 that has the Advanced Endpoint Assessment License to 8.4(3) and ASDM 6.4(7). Now there are no options in ASDM for adding AV, Firewall or AntiSpyware versions and definition levels etc? I have checked Host Scan Extensions and enabled 'Advanced Endpoint Assessment ver 3.5.3.1' however when I click configure and attempt to add any AV etc there are none to select - the 'Add Products' box is just blank.I have AnyConnect 3.0.5075, CSD 3.6.4021 and have tried with the integrated AnyConnect Host Scan image and with the standalone Host Scan image (3.0.5077) and the behaviour is the same ?
View 4 Replies
View Related
Dec 19, 2012
I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.
View 1 Replies
View Related
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Jan 2, 2013
I just recently got out of school and started my first job in the IT field. I'm at a small company and part of a 2-man IT team.One of our current projects is to look into upgrading our software based firewall (ClearOS free version) for a better hardware one. I was wondering what would be some good options?Our company has around 120 users that access our network. We have one 10Mbps internet line that comes to our head office, and is then shared with our six other branches. We're hoping to just get one device we put at our head office.some of the nicer features we'd like are AD integration, usage reports by user, easy to use interface, spam-filtering, and ability to block specific applications on websites (eg, only chat on Facebook).
View 1 Replies
View Related
Feb 11, 2013
Client has a 5515X and two ISP connections and a 2911 router to use for ISP connections. The 2911 as configured only has three ports. They nat a lot of stuff to public ips. What are my options for designing ISP failover?
View 2 Replies
View Related
Feb 12, 2012
I'm trying to get IPSec VPN working onto a new Cisco ASA5505. Pretty standard configuration.Setup:
* Cisco VPN client on Windows 7 (v5.0.07.0290 x64 on Laptop1 and v5.0.07.0440 x64 on Laptop2)
* PPPoE/NAT and internal DHCP on the ASA were configured with the Startup Wizard in ASDM
NATting is working fine - internal PCs get an IP address in the 192.168.2.0/24 range and can all access the Internet.I wanted to be able to connect from anywhere to the ASA in order to reach one of the internal servers. Should be pretty basic.First I tried with the built-in ASDM IPSec Wizard, instructions found here.VPN clients can connect to the ASA, are connected (until they're manually disconnected), but cannot reach the internal network nor the Internet. Note VPN client can connect fine to a different VPN site (not administered by myself). [code]
Unfortunately I'm getting the same "AddRoute failed to add a route with metric of 0: code 160" error message.I'm very confused as this should be a pretty standard setup. I tried to follow the instructions on the Cisco site to the letter...The only "differences" in my setup are an internal network of 192.168.2.0 (with ASA IP address 192.168.2.254) and PPPoE with DHCP instead of no PPPoE at all.
View 5 Replies
View Related
Jan 13, 2013
We have a customer, who has the following setup:
ISP router with ip range: x.x.202.1/ 28
That is connected to a Cisco 2960 switch, that doesn't do much but:
Vlan5: x.x.202.14 /28
Port 1-12 is switchport mode access to vlan 5 There are 3 firewall's connected to the 2960
1: D-Link DSR-1000N with ip x.x.202.2 /28
gw: x.x.202.1
2: Uknown
3: Cisco ASA 5505 with ip: x.x202.7 /28
static route: x.x.202.1
Each FW have a LAN behind it. The D-Link and the unknown device are both working perfectly and clients on each subnet can connect to the internet?However when I connect the ASA 5505 to the 2960 SW with a configued static route: Route Outside 0.0.0.0 0.0.0.0 x.x.202.1 1 is says it has no route to host?
Sanitized Config for the ASA 5505 is:
hostname ciscoasa
domain-name network.local
names
!
interface Ethernet0/0
switchport access vlan 2
[code]....
If I connect the ASA5505 to the LAN of D-Link DSR-1000N and give it a static address and a static route match the D-Link LAN network, it works perfectly, however not when I connect it the the Cisco 2960 Switch
View 2 Replies
View Related
Mar 17, 2011
We have a VPN setup and here's the configuration on the Cisco ASA 5505: [code] The problem is that i'm able to ping the otherside of the tunnel i.e. 192.168.23.14 from the dmz IP 172.16.1.2 but i'm unable to ping from the hosts behind the ASA.Also the other side is able to ping 172.16.1.2 IP but no IP's behind the ASA.
View 9 Replies
View Related
Sep 25, 2011
I have a customer thats got a Linksys router now, that has a DMZ port.The DMZ port is configurede to it routes the extra public ip-adress to the DMZ port it has.At the DMZ port they have another router connected, where they routes the public ip-adresses på some other devices.How can i make this setup on a Cisco ASA 5505 (With the Security Plus licens)What i have to do is to replace the Linksys router, and make it so, so it works like it was before with the Linksys.
View 5 Replies
View Related
Nov 8, 2011
i have asa 5505 , so i wanna my inside network to access to the internet. my internet gateway is 155.155.155.1
: Saved
:
ASA Version 8.2(1)
!
interface Vlan1
[Code]....
View 3 Replies
View Related
Apr 30, 2012
Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505.
View 1 Replies
View Related
Sep 25, 2011
Is there a way I can generate bandwidth reports on Cisco PIX 535 ?
View 1 Replies
View Related
Dec 20, 2011
how to configure ip sla monitoring on asa ver 7.0 (6) ?
View 4 Replies
View Related
May 17, 2011
I need to move the client machines off of the 3750 (and their DHCP dependency on it) to the SGE2010 and absolutely route their internet traffic out through the outside interface on the 5505. They must also be able to communicate back into the internal environment in order to communicate with the production servers.
The clients currently use .254 addressing through a dumb dell switch to the 3750 but I am trying to migrate them over slowly to the .253. I know that the 2010 will not do DHCP, so I am putting a DHCP server on that switch right now. The 5505 won't let me add an additional nameif statement onto one of the other eth0/x interfaces and I'm not sure if that has anything to do with it's capabilities to act as a DHCP server (it's not an option in the ASDM) or it's ability to serve as the internet gateway for the 2010 clients. (Side notes: The 5505 has a base license and is currently also connecting 1 site to site VPN. As is the 5520, so all of it's interfaces are used as well).
I statically assigned a moved client with a .253 address and plugged it into the 2010. I have tried giving the 2010 both a .4 address and a .253 address but neither will allow me to ping any of the addresses on the 5505. The 2010 shows automatic routes to the two subnets and I set it's default route to 253.1. The link between the 2010 and the 3750 works - clients receive a .254 address from the 3750 and can get out to the internet via the 5505 and reach the production servers as well.
Why won't the 2010 see the 5505 as a gateway and allow clients to get to the internet and also traverse the 3750 when they need access to the production network?
The reason why I dont' just connect the two swtiches and call it a day is because I also need the production servers to ALWAYS go out/receive web requests via the 5520 outbound/outside interface. I'm having such a hard time wrapping my head around why i can't get my clients moved over to the new switch, I haven't even grasped how I'm going to do that yet.
View 4 Replies
View Related
Jul 30, 2012
We have two sites: 192.168.100.x and 192.168.101.x currently connected via IPsec VPN. On each end we have a Cisco ASA 5505. However, each site also has an MPLS VPN with intentions to move all traffic to this link. Will this work on the ASA? We need to make sure traffic can hit the ASA @ site A on the inside interface and trafiic will forward to the MPLS VPN router which then handles the traffic. Too, will it cause any problems in bi-directional flow between the two sites?
View 3 Replies
View Related
Apr 14, 2013
I have 2 Vlans with seperate networks and want to create a route between one server in vlan 465 to another server in vlan 436 via port 80.Vlan 465 has a ASA 5505 inside that IP address 89.254.12.35 will be initiating the connection to address 10.200.1.213.
-Vlan 465: server address 10.200.1.213
-Vlan 436: server address 89.254.12.35
However for extended security I would like to restrict the firewall opening to an IP to IP opening.
View 7 Replies
View Related
Mar 5, 2012
I have an ASA 5500 Firewall. I need to figure out how to log all events using Port 25 to determine if there are any rogue devices on our network. I was trying to figure out how to do this via the Real-Time Monitoring (filter) but have had no success.
View 1 Replies
View Related
Jan 10, 2011
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
View 4 Replies
View Related
Apr 15, 2012
I am interested in gathering cumulative threat-detection statistics from an ASA running 8.3, and displaying number of attacks over time. I am already capturing traffic information via netflow, but am interested in getting threat information.
Is there a way to capture the statistics via SNMP or any other method?
View 3 Replies
View Related
Jan 10, 2012
What are considered the best practices for monitoring ASA's--specifically the 5510 with Sec+ License.
My current monitoring application keeps reporting issues with outbound interface buffers being too high, but there are not any performance issues and I believe the thresholds are just set absurdly low.
View 1 Replies
View Related
Jan 30, 2013
i have a couple of ASA 5510 in Active/Failover configuration. Failover LAN is configured on management0/0 e the ASA are connected with a back-to-back direct cable.
ASA has an interface in access mode inside with standby ip address and show failover is compliant with expected result in show failover (Normal)
ASA-PRIMARY# sh failover Failover On Failover unit PrimaryFailover LAN Interface: LANfailover Management0/0 (up)Unit Poll frequency 1 seconds, holdtime 15 secondsInterface Poll frequency 5 seconds, holdtime 25 secondsInterface Policy
[Code]....
View 2 Replies
View Related
May 21, 2013
We are using MS System Center Operations Manager to monitor network devices. We are trying to monitor our Cisco ASA 5525-X firewall interfaces.
We have a generic management pack installed that seems to work for parts of the 5525. We can see performance info for IF-4 but none of the other interfaces.
Our Management Pack is a generic Cisco Adaptive Security Appliance Version 9.1(1) management pack.
Is there a management pack that is specifically for this Cisco firewall?
View 0 Replies
View Related
Jan 25, 2011
I have a 5520 ASA running 8.2(1) and ASDM 6.2(1). The ASA has been running for 223 days without issue. Today it stopped showing real time status on the Device Dashboard from within ASDM. All of the graphs state "Lost connection to Firewall."I try to manually reconnect but it will not. I have tried on a couple different computers and cannot get the monitoring connection to work.It is a very busy firewall and I will have to schedule for a restart (which I was thinking of doing) even though I do not see a memory issue as per snip below. I don't want to restart unless it is the best option.
View 13 Replies
View Related
Dec 3, 2012
LENOVO G580 - i5,4gb ram, 500gb harddisk , network adapters- atheros ar8162 pcie- fast ethernet controller, broadcom 802.11n network adapter.i am using quickheal total secutity for a total antivirus protection.My problem is that whenever i connect my laptop using a d-link crossover cable to connect to my desktop the connection establishes successfully but on browsing or copying data the system gives a bsod error.initially i didn't got a clue as to what causes the error but then i figured out that uninstalling q-heal solves the problem an reintalling it again causes the same problem.ive tried using different versions/products of qiuckheal but all end up generating a blue screen error.not only this , whenever i use a software that has some thing to do with network like monitoring appliction wise bandwith or something it also ends up in bsod.
View 5 Replies
View Related
May 1, 2012
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies
View Related
