Lenovo G580 BSOD On Using Firewall / Net Monitoring Applications
Dec 3, 2012
LENOVO G580 - i5,4gb ram, 500gb harddisk , network adapters- atheros ar8162 pcie- fast ethernet controller, broadcom 802.11n network adapter.i am using quickheal total secutity for a total antivirus protection.My problem is that whenever i connect my laptop using a d-link crossover cable to connect to my desktop the connection establishes successfully but on browsing or copying data the system gives a bsod error.initially i didn't got a clue as to what causes the error but then i figured out that uninstalling q-heal solves the problem an reintalling it again causes the same problem.ive tried using different versions/products of qiuckheal but all end up generating a blue screen error.not only this , whenever i use a software that has some thing to do with network like monitoring appliction wise bandwith or something it also ends up in bsod.
I have lenovo g580 and it was working ok with windows starter , i formated it and now im using windows 8 but i dont have a wifi connection again and the wireless function key not working too . i downloaded a bunch of wireless drivers and installed them but still not working.
when I connect to VPN with ASA 5510, can not connect to web applications in HTTP instead https in other applications are working properly. how can I fix this?
I would like to know about asa 5500-x. Does it supports application visibility and granular control for different applications. Moreover bandwidth control based on different users and different applications
I just got a DIR-501 and wired it to my desktop. It runs great! (This DIR-601 board is the closest one I can find to DIR-501.)
After connecting the DIR-501, when coming out of hibernation or when booting up, my computer would hang, apparently after the desktop has already appeared (Win XP Home SP3). The first time this happened I got a BSOD with the following:
I have an ASA 5500 Firewall. I need to figure out how to log all events using Port 25 to determine if there are any rogue devices on our network. I was trying to figure out how to do this via the Real-Time Monitoring (filter) but have had no success.
I am new to the PIX firewall. And recently implemented the PIX 506e in my network. I wants to know how we can monitor the system that is generating the more traffic on Network through Firewall.
I have a question regarding failover monitoring on the ASA5505 in an active/standby configuration.
I understand that on the 5505 you create VLAN interfaces and then assign the VLANs to the 5505 switchports. With failover configured on the 5505, the VLAN interface names are monitored. For example, VLAN 100 interface named Inside is assigned to ethernet0/1, switchport mode access. When issuing a show failover command the output will show the monitor status of interface Inside..
Does failover monitor the VLAN virtual interface only? Does failover also monitor the link status of the ethernet0/1 switchport?
We have one pair Cisco ASA 5505 located in different location and there are two point to point links between those two locations, one for primary link (static route w/ low metric) and the other for backup (static route w/ high metric). The tracked options is enabled for monitoring the state of the primary route. the detail parameters regarding options as below,
Frequency: 30 seconds Data Size: 28 bytes Threshold: 3000 milliseconds Tos: 0 Time out: 3000 milliseconds Number of Packets: 8
[code]....
I'm not sure if the setting is so sensitive that the secondary static route begins to work right away, even when some small link flappings occur. What is the best practice to set those parameters up in the production environment. How can we specify the reasonanble monitoring options to fit our needs.
I am interested in gathering cumulative threat-detection statistics from an ASA running 8.3, and displaying number of attacks over time. I am already capturing traffic information via netflow, but am interested in getting threat information.
Is there a way to capture the statistics via SNMP or any other method?
I am trying to monitor my ASA 5505. This asa is connect via a ip-sec tunnel to our network. I have no problems with snmp monitoring devices behind the ASA, but when trying to monitor the asa itself I do not get a SNMP response.
What are considered the best practices for monitoring ASA's--specifically the 5510 with Sec+ License.
My current monitoring application keeps reporting issues with outbound interface buffers being too high, but there are not any performance issues and I believe the thresholds are just set absurdly low.
i have a couple of ASA 5510 in Active/Failover configuration. Failover LAN is configured on management0/0 e the ASA are connected with a back-to-back direct cable.
ASA has an interface in access mode inside with standby ip address and show failover is compliant with expected result in show failover (Normal)
ASA-PRIMARY# sh failover Failover On Failover unit PrimaryFailover LAN Interface: LANfailover Management0/0 (up)Unit Poll frequency 1 seconds, holdtime 15 secondsInterface Poll frequency 5 seconds, holdtime 25 secondsInterface Policy
I recently replaced my harddisk and ever since I've been getting BSOD's whenever I try to watch a video online (no matter what website I'm on). I'm pretty sure it's not my GPU, because I can watch my own videos just fine. It could be the RAM,ause I ran Memtest86+ for 7 passes and it found two errors, but I have no problems playing games. So, I'm thinking it's my network-driver (Realtek) even though I already (re)installed the latest version[CODE]
We are using MS System Center Operations Manager to monitor network devices. We are trying to monitor our Cisco ASA 5525-X firewall interfaces.
We have a generic management pack installed that seems to work for parts of the 5525. We can see performance info for IF-4 but none of the other interfaces.
Our Management Pack is a generic Cisco Adaptive Security Appliance Version 9.1(1) management pack.
Is there a management pack that is specifically for this Cisco firewall?
I have a 5520 ASA running 8.2(1) and ASDM 6.2(1). The ASA has been running for 223 days without issue. Today it stopped showing real time status on the Device Dashboard from within ASDM. All of the graphs state "Lost connection to Firewall."I try to manually reconnect but it will not. I have tried on a couple different computers and cannot get the monitoring connection to work.It is a very busy firewall and I will have to schedule for a restart (which I was thinking of doing) even though I do not see a memory issue as per snip below. I don't want to restart unless it is the best option.
Since recently replacing my home router with a Linksys E2500, I have been getting Blue Screen of Death (BSOD) with my Company's VPN (AT&T). It only happens when I am running wireless with my E2500. If I am hooked up to my E2500 through a ethernet cable it doesn't happen. I have updated the BIOS on my Lenovo Thinkpad T410 and ensured all of my drivers are up to date. I am 99.9% sure the problem is caused by my Linksys E2500 because I have used my laptop on other wireless routes at work and school and never get this problem. I am also ensured that my E2500 has the current firmware installed and upgraded my Company's VPN to the most current level to no avail.
I am getting DRIVER_IRQL_NOT_LESS_OR_EQUAL Blue Screen of Death in agnfilt.sys.
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
Dell dimension 2400 XP home. Connects fine to old linksys g router.With new qwest dsl modem/router get IRQL not less than or equal as soon as I click on connect .Blue screen stop and must reboot.Qwest router works fine with my lenovo lap top. Win 7.
I'm currently implementing Microsoft System Center 2012 Operations Manager, the curent stage of the project is to add the network devices to SCOM via SNMP in order to monitor them, I am able to add them all and monitor; however, my ASA 5510, although SCOM discovers the ASA via SNMP and adds it to the network monitoring list, it loses SNMP connectivy every 30 minutes, and 15 later it reconnect with SCOM, then after another 15 minutes it loses the connection again, and so on and so for.
I just did a fresh install of windows 7 x64 on a 2tb hd. the only drivers I have installed are the chipset, the onboard audio, usb 3.0, onboard HD GFX, marvell raid controller, and the intel management engine. The only other program installed is intel desktop utility. my onboard NIC is not working. i get an error saying the Local Area Connection doesn't have a valid IP configuration. I've tried setting the IP's and DNS addresses manually. I've tried disabling flow control. I've tried disabling IPV6. I've tried restarting the computer numerous times. The cable is fine, it was working yesterday. This also happened a couple days ago when I uninstalled my BigFoot 2100NIC, so I just said screw it and reinstalled it and internet worked great after that. I've tried pinging two adresses and it failed to ping 192.168.1.1 (the router address). I'm considering just installing the BigFoot I have right next to me, but i'm hesitant because the whole point of the clean OS install was to diagnose a stop 124 BSOD. I guess the question is would I rather have internets or GPU (the hardware I was planning on installing next), but its puzzling me why my onboard NIC is not working.
Here's my IPconfig/all. I've already reset ipv4,ipv6 and winsock through cmd with admin.
Windows IP Configuration Host Name . . . . . . . . . . . . : Erik-PC Primary Dns Suffix . . . . . . . :
About 10 months ago I got a new computer, with it I got a the Linksys AE1000 wireless adapter. At first all was fine, no blue screens. About a month after I got all my game and such installed (I am a bit of a gamer) I started to get bsod error 0x0000000D1 in the middle of my game. I wasn't sure the cause of the problem, so at first I ignored it. I started to get the same error more and more frequently and the same cause of the problem. I believe that the wireless adapter is the cause of the problem, but alas I can never be sure..
Trying to install WMP54G v4.0 on XP SP3. I have tried all three PCI slots. Removing driver RT2500.SYS system will boot. Put it back and BSOD Error:driver_irql_not_less_or_equal
Region : UnitedStates Model : TL-WDR3600 Hardware Version : V1 Firmware Version : 3.13.26 Build 130129 Rel.59449n ISP : Charter
I've set up my printer (HP PSC 2410) to the router using TL-WDR3600_V1.0_USB Print Service Client Setup and that part's fine. The USB Printer Controller sees the printer as an "auto-connected printer" and I can select the printer as my default to print to. My problem lies with the fact that every time I try to print something, it causes a BSOD. I'm using Windows 8 and checked to make sure the USB Print Service Client Setup program was compatible with Windows 8 before I attempted anything. The HP PSC 2410 printer is on the Print Server Compatibility list so I don't know why I'm having problems.
The error I get each time I try to print is: SYSTEM_SERVICE_EXCEPTION (TplinkUDSTcpBus.sys). One of the draws of this router was that I could hook up my printer via USB and print wirelessly
My dad recently purchased a wireless LAN card to connect to our router for ADSL internet. The card is labelled on the box as a Mecer WF-2113M 300Mbps Wireless-N PCI-E Adapter. Link: WF-2113 Mecer 802.11b/g/n Internal Wireless PCI-e Card - Mecer
First off I could not get the card to work with the original drivers that came with the card so I updated the drivers. (The card's chipset is a Realtek RTL8192CE). After the driver update the card worked perfected until the BSOD's started completely at random. see attached image with description of BSOD.
PC's Specs: Asus P8H61M LX Motherboard Intel Core I3-2100 CPU @ 3,10ghz 2x2gb DDR3-1333 Ram Gigabyte ODIN 460w PSU Nvidia Geforce 9500Gt GPU Windows 7 Ultimate x64
The PC was running perfectly before we installed the card. Is there anything that I can do to solve the issue? Unfortunately I cannot test the card in my PC or my brother's as we both don't have PCI-E x1 slots. Also not sure the PC shop will take the card back.
Most of my applications and games that connect to the internet are unable to do so. My browser is working fine, though.This morning, my AVG found 2 trojans, and deleted them. However, it also deleted a couple registry keys along with them. I suspect this might be the problem, or maybe the antivirus itself, but I don't know which keys were deleted.
I randomly get disconnected from the online applications that I'm using.(Msn, skype, online games, etc.)And I'm running this program in the background to check what's going on.As you can see, everything is normal till I get 0 ping for a couple of times, then it immediately goes back to normal till it hits 0 ping again.It's very random, it happens on the 345th hop or 789th etc.I'm on a wi-fi connection but not using wireless modem.The cable's plugged to my computer.
We are having issues transferring a 200GB VHD file across our point to point without being corrupted in the process. Any good application for testing the line quality across the point to point?Preferably we want something free, but if there is an in depth tool that costs money, we are open to that option as well.
I've tried scanning for viruses, using winsock fix (they had a static ip I also set to automatic since they should not need it). I just turned off the firewall as well, tried "selective startup" and unchecked "load startup items" and nothing has worked so far. We're working on giving them another computer but I'd like to know why this happens.
I recently was instructed to block Facebook from a specific persons phone. I was able to block access to Facebook from the browser, but this person can still access Facebook via the mobile app. I have already placed m.facebook.com and facebook.com on the "no-go list" on my router, which like I said, specificaly blocks the browser on phone, but not the app. I can't seem to figure out how the app accesses the site and how to block it.I've already done some Googling, and read that port 9339 plays some kind of role. I don't know how true this is, but I tried it anyway, to no avail. I am not to savvy with ports so it could be my error.And before it is mentioned, this person cannot access cell data, as the phone does not get service, only WiFi.
