I have a ASA 5510 that has something weird going on I have just added a base config where you can access on a inside interface but for some strange reason after I disconnect i have to ping inside interface first before I can connect via telnet or SSH and then regenerate therecrypto key
View 3 RepliesWe have two Cisco ASA 5510 Firewalls at one site, and two non-Cisco firewalls at another. Both firewall pairs are configured for high availability (Active-Passive), and both have redundant links to the Internet via routers running HSRP. In the event that one of the Internet routers were to fail, we require the VPN to dynamically move from using the old path via the failed router to using the new router with minimal downtime.
I have been looking at using VPN load balancing to achieve this but the only configuration example I can find is for Cisco VPN Client url... Is it possible to define a static crypto map with the VIP of the load balanced group as the peer IP? So in the non-Cisco devices I will define the VIP of the load balanced group?
This setting is correct?
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
[Code]...
I am currently getting a strange error when trying to use and crypto services on our ASA 5520 (8.0.3)Initially I observed that a connected VPN had dropped.Then when I attempted to use ASDM or SSH I was blocked.
In the end I opened telnet as a test and this was successful. Syslog also shows that traffic is passing as normal.The only obvious error I can see when observing various debug traces is this;
FW02# CTM: rsa session with no priority allocated @ 0xCF1FBBA0
CTM: Session 0xCF1FBBA0 uses a nlite (Nitrox Lite) as its hardware engine
CTM: rsa context allocated for session 0xCF1FBBA0
CTM: rsa session with no priority allocated @ 0xCE7A5EA8
[code]....
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies View RelatedI have to connect one of our it labors with some ec2 instances in amazon vpc. I downloaded a configuration file from amazon which starts with the command
crypto isakmp policy 200
My router tells me that he does not know crypto isakmp.
I searched on the internet and found that i have to install a specific license, but unfortunately i cannot find which license i have to install.
The show license command show following licenses
AdvIpServices active
AdvSecurity active
advsecurity_npe, ios-ips-update, waas_Express no state displayed
ssl_vpn active but eula not accepted
I found that i can accept the eula license with license boot module c880-data technology-package SSL_VPN command
But this command is also not available on my device. getting the crypto isakmp command working?
I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies View RelatedWe were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedI would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
View 1 Replies View RelatedI have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
I have just configured identity firewall on our ASA 5510.I have 3 nodes that authenticates against Active Directory, using the Windows Server 2008 R2 builtin Network Policy Server: A laptop, a stationary PC, and a Android Phone. All 3 nodes are authenticated using the same user/password.
Now, in ASDM -> Monitoring -> Properties -> Identity -> Users, I can see two of the nodes with my user name attached to it, namely the laptop and the stationary PC.But not the Android phone.
Then it dawned on me. To set up the ADAgent properly, you have to apply 2 group policy entries. Unfortunately, those 2 entries are applied to the Computer Configuraton part of the Group Policy.This means that your COMPUTER has to be a member of your domain for USER IDENTITY to work.So my Android phone and other nodes not a member of the AD Machine Store will never be detected by identity rules, and can roam the network free.
I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
i have 2951 ISR but i cant configure encryption it have UniversalK9 IOS and i cant find any other ios that will support crypto map?
View 4 Replies View Relatedi have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
I have a Cisco 881 ISR (CISCO881-SEC-K9) and have the advanced security license installed and enabled/active and in use (see screenshot). However, the isakmp crypto module is not available.
[code]....
I currenty have 2 cisco 5510 firewalls one of the firewals is completly dead but contains a Cisco ASA SSM-10 can i remove this card and just place it into a working unit, will i have any problems doing so.
View 1 Replies View RelatedI am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
This is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedWe have setup new ip camera system and as per our vendor to access the camera from outside we need to open,TCP ports and in firewall and forward to our camera server.
Let say our public ip address is 207.114.111.22 and our local ip address for the camera is 11.11.1.30. We have cisco asa 5510.
We've in our company a Cisco Asa 5510 v8.4(3), Asdm 6.4(7) and a SSM-CSC-10-K9. The firewall is in transparent mode. I get an exchange 2003 SP2 server behind. When users trying to send mailing lists with many recipients (above 300), the Exchange server didn't send these mails. I'm pretty sure that this problem come from the ASA Firewall, because when I plug my server directly on my Internet Connection, the mailing list is sent. I've search on the web, and disable "ESMTP Inspection", but it didn't work. [code]
View 4 Replies View RelatedI have applied a crypto map (fo ipsec vpn) on the dialer interface (for PPoE connection) in Cisco 2800; every time when the router restarts the crypto map is removed from the dialer interface even though i save the configuration every tim when i apply the map on the interface. Is there any way that the crypto map remains there on the dialer interface after the restart of router.
View 1 Replies View RelatedIn a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedIn my test lab , I have a CISCO 1841 with a AIM-VPN/BPII-PLUS board , everything was working fine , until I would like to see the difference with and without the accelerator.Sins the moment that the IOS told me that he will change to SW accelerator instead of HW accelerator , I can not make it work anymore.I have a copy of the full working configuration before I did this , I have put it back on my router but still NO VPN. [code]
View 2 Replies View RelatedI have a network architecture like the one HERE but with alot more spokes (32). Would my cisco 3925 be able to support so many crypto maps?
View 2 Replies View RelatedI am trying to configure Crypto PKI in ciscio 2911, Once i configured the root certificate for the router , i can see the validity date wrongly but the same certificate is fine in the other devices . [code]e when i am trying to configure the local certificate.
View 1 Replies View RelatedNew to the forum and not much Cisco IOS experience let alone on the security side of things. I know how to navigate the IOS and can do basic switching and routing just fine. My company currently has a DMVPN setup w/ about 10 tunnels going back to the hub. We have 4 more sites they want me to setup and I keep getting stuck at the crypto maps. I have been reading about VPN's, DMVPN's , etc. for days now but can't find any examples of how we are configured. The priority of our crypto maps start at 65536 and go up. Default max is 65335 from what I have read, and I cannot assign a priority that high statically. [code]
View 3 Replies View RelatedI ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.
View 5 Replies View RelatedI have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.