Cisco VPN :: 2651 No Matching Crypto Map Entry For Remote Proxy
Jul 14, 2011
ASA is the server, 2651 is the client. Phase 1 is negotiating, after entering XAUTH on the 2651, the ASA is showing:
Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 10.250.2.0/255.255.255.0/0/0 local proxy 10.10.3.0/255.255.255.0/0/0 on interface Outside
Not sure what this means in this instance, the maps are setup the same as the article below. I guess I more expected that sort of error if this was a static tunnel and there was an ACL issue. I don't have a lot of knowledge on the Easy VPN with the ASA. [code]
View 1 Replies
ADVERTISEMENT
Feb 10, 2012
I am using a proxy to access the internet on my computer, how can i use that proxy on my iphone, when sharing internet connection?
View 2 Replies
View Related
May 11, 2012
I want to connect via windows rdp to computer outside the company office and I cannot do that since we have webwasher or proxy installed in the office.I can access this machine with IE (it is a server with open port 80) and I see its website. This is becuase the IE at office has proxy configured correctly.I cannot access the same machine with RDP connection, though. I can access it using other computer outsite the office, so it is not an issue that rdp is not enabled or so. Problem is with proxy at office.I need a way to connect to rdp by using the same proxy.Problem is that that IE at office uses automated proxy script (.pac).I have installed remote utilities server on the machine I want to access and the remote utilities viewer on the computer at office. I set the proxy similary to what is set in IE but I cannot connect anyway. I can connect this way from third computer outside the office though, so the configuration is fine, only proxy is the problem.I managed to get the proxy details like host name and port but I'm not sure those are the right one.The webwasher or proxy is mcafee web gateway 6.8.4.
View 1 Replies
View Related
Sep 26, 2011
I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?
View 2 Replies
View Related
Sep 28, 2011
I have a 2651 IOS ver 12.2(8) T5 and I installed an ATM-T1 4T1-IMA WIC, but the router will not recognize it. Do I need a newer IOS or is there a command to have the router recognize this WIC? Currently it is connecvted to our ISP via the serial connection, but they want to go to an ATM protocol for better video performance.
View 6 Replies
View Related
May 18, 2012
I have some Cisco 2651 routers, I was trying to implement MPLS on those routers, Can i accomplish this upgrading newer IOS version? link to download the supported IOS.
View 2 Replies
View Related
Dec 30, 2011
I have a 2651 that has an adsl1-wic that I am using as my DSL router. I recently acquired a 2801 that I want to replace the 2651 with. I configured the 2801 the same way as the 2651 but on a reload I get the statement that says
Setup: New interface NVIO placed in shutdown state
When I do a show interface all of the interfaces show up except the NVIO and I don't have any connectivity to the outside world. I am using Nat since I have a /29 and using nat pool overload. What am I missing? I am running IPVOICEK9-M 12.4.25c on the 2651 and adventerprise 12.4.24.T on the 2801
View 7 Replies
View Related
May 20, 2013
I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies
View Related
May 28, 2012
I would like to connect devices to my network so that their traffic passes through a proxy running on my computer. I figured the best way to do this is by setting the proxy on my router to the one I am running, but then I would need to have another connection to the computer running the proxy or else there would be an infinite loop ?? something like that. so:
Internet -> router (1) -> my proxy on comp A -> router (2) -> computer B
View 1 Replies
View Related
Mar 31, 2012
I access the internet from my company�s LAN, which has a restrictive firewall, so I cannot request the admin to open any ports manually for me. Hence I use a software called your-freedom. This proxy software supports both http as well as socks 4 and 5 proxy (by entering the proxy IP 127.0.0.1 (localhost) and Port 8080 for http proxy OR 1080 for Socks Proxy), and I have successfully been using web browsers and some other softwares that support proxy/ allow proxy info to be entered to login/ connect to the internet. Your-Freedom also supports port forwarding.However, the softwares I intend to use do not have any options to enter proxy methods or proxy ports (as far as I have noticed). I have tried to proxify these 2 softwares using softwares such as SocksCap and Free Cap, but either they don�t work, or my settings in proxifying are not correct. I believe I will have to do port forwarding or proxify the softwares, but have been unable to do so in the correct manner.
Following is the info on the 2 softwares:
1.NOW Trading terminal:[FONT=Times New Roman]Normally when I start the NOW or Zerodha software, the software starts and I get a login screen, but under firewall conditions, I get the initial Splash screen but then the software stops with the error: [b][u]NOW Initialisation failed for Interactive Engine << os error>>.
2.PowerIndia Bulls:The software is written in Java and starts with a batch file (PowerIndiabulls.bat) located in C:UsersDEFAULT_USERNAMEAppD..... I converted this batch file to .exe (with battoexe software) and then ran it through a proxifying software. The .exe start properly without proxifying software but not under proxifying environment. Basically the software needs to connect to the internet using Port 443. I am also expected to keep ports 443, 41599 and 59598 open. software's requirement is available at Indiabulls Securities: Indiabulls Securities is a leading capital market company offering securities broking and advisory services, depository services, equity research services to its clients in India. (item no. 5).To confirm, while the software is unable to connect through port 443, you will get an error message: "Connection to Login Server could not be established" when you try to login with any random Username and Password.To know that the software is able to connect properly, you will get an error: "This User ID is not enabled to be used with this product".
View 1 Replies
View Related
Dec 7, 2012
I believe that the Cisco Unified Communications Manager Express matches the outbound VoIP dial peer digit-by-digit, because:
1. when using the debug command it shows how it works digit-by-digit till it match a pattern
2. It says in the study guide ( If a match is found, the router immediately processes the call - chapter 6) so I understand its not en bloc
View 3 Replies
View Related
Aug 15, 2011
my config and all the show's ive run sofar tryign to figure this out, but the policy map isnt matching the traffic for some reason
View 9 Replies
View Related
Jan 8, 2013
Anyone know the differnce between these two on a MLS? Seems that proxy arp as I know it works with or without the 'local' version.
View 7 Replies
View Related
Oct 3, 2012
I have a Cisco ASA running 8.2 in routed mode.The ASA has three interfaces, inside, outside and DMZ. They connect to the following three networks:
Inside: 10.1.1.0/24
Outside: 10.1.2.0/24
DMZ: 100.1.1.0/24
I have the following dynamic PAT configuration:
nat (inside) 1 10.1.1.0 255.255.255.0
global (outside) 100.1.1.1
nat control is turned off.
By my understanding any traffic from the inside to outside interface will be PATted to 100.1.1.1. However, communications between inside and the DMZ will not be PATted, and should work with no problems.This seems to be corroborated by this document: [URL]Which states:"The adaptive security appliance translates an address when a NAT rule matches the traffic. If no NAT rule matches, processing for the packet continues."EDIT: I may have misunderstood the above statement.I found this guide to configuring NAT/PAT: [URL]It states:"When you specify a group of IP address(es) in a nat command, then you must perform NAT on that group of addresses when they access any lower or same security level interface; you must apply a global command with the same NAT ID on each interface, or use a static command. NAT is not required for that group when it accesses a higher security interface because to perform NAT from outside to inside you must create a separate nat command using the outside keyword. If you do apply outside NAT, then the NAT requirements preceding come into effect for that group of addresses when they access all higher security interfaces. Traffic identified by a static command is not affected."My problem is that packet tracer does not seem to bear me out. It tells me the packet is dropped due to "no matching global" when I source traffic from the inside interface and send it to the DMZ.
View 3 Replies
View Related
Sep 20, 2011
I have a command line from ASA 5505 like below :
nat (inside) 0 access-list NO_NAT
The problem is I cannot see any matching ID of 0 at the (outside) like :
nat (outside) 0 xxxxxxxxxxxxx
Another problem is there is also no any access list with the name of NO_NAT.
View 2 Replies
View Related
Jun 24, 2011
Got to set up a site to site VPN to one in a clients office and we're struggling to get Phase 2 working, just seems to loop around saying "Received encrypted packet with no matching SA, dropping" which to me means the ACLs arent mirrored correctly?
View 3 Replies
View Related
Mar 29, 2012
i have firwall ASA5400, and the outside interface connected to internet router but i noticed that the interface speed in the outside interface is 1000M, but on the internet router is 115 M. so the interface in the router is highly utilized and also the firwall cpu highly utilized. [code]
View 0 Replies
View Related
Jun 23, 2011
I am trying to set up remote access vpn on an asa 5520 running 8.4.1. I have the ipsec group, policies, and ip pool set up. When I try and connect with the cisco vpn client I see the following in the logs. Deny icmp src outside:214.67.39.42 dst outside:24.252.51.73 (type 3, code 3) by access-group "acl_inbound". Do I need to put in some firewall rules to allow this traffice so that the VPN can connect?
View 9 Replies
View Related
May 15, 2012
I am trying to remove a static route I added: [code]
I was practicing setting up static routing on three routers r2 (2600xm) connected to r1(2600xm) via T1 module cards on the serial ports. connected to r1 is an old 2500 router called PC.
I removed the static routes off r2 and PC but when I get to r2 which I am connecting to via console cable from another 2500 that I use for an access server I get the above error. all the IPs are just generic subnets I created to play around with static routing. I
View 4 Replies
View Related
Aug 23, 2012
We are configuring a twice-nat to send traffic for scansafe, its on a asa5505 ve 8.4(3) on a remote location for the customes. The nat redirecion is working but we also have a VPN tunnel to the corporate network. Through the tunnel we need to reach a http server. The problem we are having is that when we add the scan-safe nat, all http traffic gets redirected to scansafe, includind the traffic to the http server on the corporate network.
10.2.1.0 ---<ASA5505> ---Internet,scansafe ---- <Corporate> --- 10.1.1.0
the http server is 10.1.1.75
the remote location network is 10.2.1.0/24
[Code].....
View 9 Replies
View Related
Jan 12, 2012
I'm performing tests with following desired scenario: We have several remote offices, connected to our HQ via MPLS. In these remote offices, we have several vlan's. Each vlan has it's own ip-range. The MPLS cloud is routed, so we cannot switch our HQ vlan's to the remote offices. In this case, the client pc is in a guest vlan which allows him internet access. The uplink for this internet access is hosted in our HQ datacenter.
basic scheme:
client pc --> MPLS cloud (managed by ISP) --> 6500 switch LAN --> Checkpoint Firewall --> 6500 switch DMZ --> ASA Firewall
My test scheme:
Client pc is in a subnet A (guest vlan range office).
We receive this traffic on our first LAN 6500.
[Code].....
View 29 Replies
View Related
Sep 18, 2012
My company is composed of three different campuses, all with a similar network topology. We currently are experiencing high bandwidth on our serial interface at one of the campuses in particular. The network is composed of about 20 VLANS routed internally using a Cisco 6509. Traffic to the outside is PAT’d by an ASA 5510 and then forwarded through our edge router interface. Each VLAN is PAT’d to a specific public address.Due to the PAT, how would you recommend determining what specific private addresses are consuming our resources on the serial interface. When I look at our NMS, it reports the public address, but that only narrows it down to a VLAN. For example, all the devices in VLAN 6 are translated to 146.34.118.245, and 146.34.11.245 is a top talker.
View 1 Replies
View Related
May 15, 2012
RV220W - I'm trying to create a one-to-one NAT connection to a PC on my network. I have 5 static IP's assigned by my ISP. I've gone through the step of 'registering' each IP in turn on the WAN port, and pinging that IP from an external device until it starts to respond, then I set the WAN IP back to the one I want to use to manage the device.
I think what I want to do is simple. I simply want to NAT ALL traffic hitting my 2nd IP address, let's call it 24.15.120.73 (not the real value) to 192.168.1.10 internally. I want ALL ports both UDP and TCP to be forwarded. This Server is then going to be one end of a VPN tunnel going to another site, but I don't want to complicate things with that for now. So I can't even seem to get one-to-one NAT working! I created the one-to-one NAT on the Advanced tab of the firewall and created rules for all ports for UDP and TCP, but I can still never 'see' the internal server from the Internet. Also, the server will not get out to the Internet (can't hit Google, etc).
View 2 Replies
View Related
Jul 2, 2012
My router password is "55xxxxx"
But when I want to change the router password in CCC, it warns me "Current password is not match"
View 1 Replies
View Related
Sep 6, 2012
Im having a (from google-fu) seemingly unique issue with load balancing. So for background, I am running the ACE 4710 device in "on a stick" mode, so I am using NAT and all that good stuff. I am also utilizing class maps and host header matching so I can save on IP space. [code]
Basically, as soon as I add that ACL_CLASS_beta.mainsite.com class map, all I get back from the ACE is RST packets and it comes back with an L7 LB Policy Miss.
It SEEMS like it should work, but it doesnt seem to like matching on those source addresses at all.
View 1 Replies
View Related
Mar 7, 2011
I have this situation, I need to establish an IP sec communication to another site but I need to identify all my packets sent, as a different networks as my local one. for example: my local network is 10.5.0.0/24 and I need to sent packets as 10.6.0.0/24. I suppose that I need to do Nat with this IPs. But in this router Nat is already applied to outbound traffic to Internet. How can I apply this NAT to crypto map only?
My router is a Cisco 877 with 12.4 IOS an this is the relevant configuration, crypto map vpn it´s used to sent traffic to second site.
crypto isakmp policy 2 encr 3des authentication pre-share group 2crypto isakmp key xxxxxxxxx address XX.XX.XX.XX
crypto ipsec transform-set vpn esp-3des esp-sha-hmac
crypto map vpn 1 ipsec-isakmp set peer XX.XX.XX.XX
[ code]....
View 2 Replies
View Related
Jan 11, 2013
I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies
View Related
Jun 26, 2011
I have to connect one of our it labors with some ec2 instances in amazon vpc. I downloaded a configuration file from amazon which starts with the command
crypto isakmp policy 200
My router tells me that he does not know crypto isakmp.
I searched on the internet and found that i have to install a specific license, but unfortunately i cannot find which license i have to install.
The show license command show following licenses
AdvIpServices active
AdvSecurity active
advsecurity_npe, ios-ips-update, waas_Express no state displayed
ssl_vpn active but eula not accepted
I found that i can accept the eula license with license boot module c880-data technology-package SSL_VPN command
But this command is also not available on my device. getting the crypto isakmp command working?
View 5 Replies
View Related
Sep 4, 2012
I have a 2650XM 16mb flash, 64 mb ram. 12.2(12a). now I want to buy 12.4(25d) with crypto. How much is it? And where can I buy it ?
View 10 Replies
View Related
Aug 8, 2012
i have 2951 ISR but i cant configure encryption it have UniversalK9 IOS and i cant find any other ios that will support crypto map?
View 4 Replies
View Related
Aug 5, 2012
i have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
View 6 Replies
View Related
Jun 13, 2012
This setting is correct?
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
[Code]...
View 1 Replies
View Related
Aug 21, 2012
I have a Cisco 881 ISR (CISCO881-SEC-K9) and have the advanced security license installed and enabled/active and in use (see screenshot). However, the isakmp crypto module is not available.
[code]....
View 2 Replies
View Related
