Cisco WAN :: Configuring HWIC-2SHDSL Card In A 2911 For CO Mode Operation?
Dec 12, 2011
I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
View 3 Replies
ADVERTISEMENT
May 19, 2013
I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies
View Related
Oct 10, 2011
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
View 3 Replies
View Related
Feb 14, 2012
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies
View Related
Jul 13, 2011
I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
View 5 Replies
View Related
Mar 16, 2010
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies
View Related
May 9, 2013
wether the Cisco RV180 router model can be configured with a public IP address on the LAN interface? I'm planning to use it in the following setup:
Internet ------------- WAN port (public IP) RV180 LAN port(public IP)-------------- WAN(public IP) RV016 LAN (private IP)
Disabling gateway operational mode and switching to router should disable NAT and allow this setup but need to confirm if it works? I'm concerned if the web management interface actually allows a public IP to be set on the LAN side.
View 1 Replies
View Related
Oct 6, 2011
According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies
View Related
Feb 24, 2013
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
View 2 Replies
View Related
Feb 27, 2012
On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
View 9 Replies
View Related
Oct 11, 2012
We plan migrate an old existing WAN architecture based on legacy data serial links. These links will be consolidated on a E1 channalized card.
My question :
Is the HWIC-2CE1T1-PRI need a PDVM DSP ressources on router to oparate for data leased lines or no?
The VWIC3-1MFT-T1/E1 will be used for the backup dial in ISDN connexions? this type of cards a PVDM DSP ressources for data connexions or no?
ISR router are 2911.
View 5 Replies
View Related
Mar 26, 2013
I just added an HWIC-16A to a Cisco 2911 router for use as a Terminal Server.[URL]I've installed and configured the card properly. However, I receive the following error message:Attempt from Cisco CLI
View 2 Replies
View Related
May 3, 2012
I am trying to configure multiple dsl-groups on a HWIC-4SDHSL-E module and the option does not exist. According to the Cisco documentation I should be able to do this, but I only get pairs as an option.
1921(config-controller)#dsl-group ? pairs Link number <cr>
[URL]
This is what I am trying to do which I have done before on the 1841.
dsl-group 0 pairs 0, 1
shdsl annex A-B
shdsl rate 4096
[Code].....
View 1 Replies
View Related
May 10, 2011
I have a CISCO 1841 with a HWIC interface to my ISP. I want to make a ADSL connection and my current running-file is: [code] The problem I have is that the ISP connection is established but then goes down.
View 1 Replies
View Related
Dec 5, 2011
if the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies
View Related
Dec 18, 2012
I was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
View 6 Replies
View Related
Aug 19, 2012
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
Sep 2, 2011
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Sep 27, 2012
I configuring QoS policing in a Cisco 2911 in a 128K/256/512 link, but when I apply the configuration in interface I receive the error below:
Configured Percent results in out of range kbps.Allowed range is 8-2000000. The present CIR value is 6.
Current configuration : 191 bytes
!
interface GigabitEthernet0/1
description ***V-SAT***
bandwidth 128
[Code].....
View 7 Replies
View Related
Jan 23, 2011
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
View 2 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Feb 27, 2012
I am trying to configure Crypto PKI in ciscio 2911, Once i configured the root certificate for the router , i can see the validity date wrongly but the same certificate is fine in the other devices . [code]e when i am trying to configure the local certificate.
View 1 Replies
View Related
Apr 5, 2011
We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies
View Related
Mar 20, 2013
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
View 1 Replies
View Related
Jun 5, 2011
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies
View Related
Jun 10, 2011
I have configured Priority Queueing in my Cisco 2911 Router. I have set queue list high, medium, normal and Low. But when I put show interface gi0/2, it is showing the queueing strategy is priority queueing but it is not showing the (size/max/drops) values.
View 1 Replies
View Related
Nov 2, 2011
I have a 2911 router where I was configuring the device to allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared.
View 5 Replies
View Related
Apr 27, 2011
Purchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
View 1 Replies
View Related
Jun 14, 2011
From all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies
View Related
Mar 27, 2013
We're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies
View Related
