Cisco WAN :: Adding A HWIC 1FE Card To 2811 Router?
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
ADVERTISEMENT
Jun 12, 2011
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Apr 20, 2012
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies
View Related
Feb 14, 2012
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies
View Related
Sep 2, 2011
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies
View Related
Jan 23, 2011
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
View 2 Replies
View Related
Mar 20, 2013
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
View 1 Replies
View Related
Jan 2, 2012
I'm trying to learn a little about Cisco router setup, since I'm fairly well versed in configuration. I have an 1841 w/ K9 that I'd like to set up as a WAN Router to hot swap if one of ours goes down. I installed a VWIC2-1MFT-T1/E1 MultiFlex card in Slot 1 of the router.
Currently, if I run a "show diag", the VWIC2-1MFT-T1/E1 shows up in Slot 1 but in the configuration I can't see it or configure it. Am I missing an enable or something? I thought I had to declare card type but I can only do that on the existing card, the router doesn't seem to recognize that the card is there in any place other than "show diag".
View 7 Replies
View Related
Sep 7, 2009
I would like to ask if a cisco 2811 running on an ios c2800nm-adventerprisek9-mz.124-25a.bin should be able to make an HWIC-1FE card work? I am also not detecting the card on any show commands. Plus i am seeing that all the LEDs (FDX/COL,100 and LINK/ACT) are lit steadily even though there is no cable attached to it, is it safe to say that the card could be defective?
View 6 Replies
View Related
Oct 26, 2011
i am currently trying to configure a four port ISDN BRI interface on a Cisco 2811 router.Upon upgrading to a later version of IOS, c2800nm-advipservicesk9-mz.124-25d.bin, access to the HWIC-4B-S/T module is lost, the router no longer detects it. In fact iI can only get the router to detect the module using the original IOS version c2800nm-advipservicesk9-mz.124-20.YA3.bin.
Is there some special feature needed in the IOS code to support these modules, if so what would be a suitable version/train to upgrade to?I have tried using the Cisco Software advisor tool but it generates an error when searching on a hardware configuration containing this module type.
The reason for upgrading the code is we have a potential bug with the current version which appears to be preventing the BRI interface syncing up with the providers switch (switch type correctly defined and provider confirms isdn line has been provisioned correctly).
The debug error seen is:
GMT: ISDN BR0/0/0 SERROR: L2_Go: at bailout DLCB is NULL
L2: sapi 63 tei 127 ces 0 ev 0x650
My main question though is why the module is not being detected after a code upgrade and if there is a specific code version/train needed to support this module in a 2811?
View 11 Replies
View Related
Jan 23, 2012
I am adding another ISP (and plan to use BGP). I am looking at having two 2811's with one connected to each ISP, or a single 2811 (with an additional HWIC) connected to both ISPs. I am not sure if there is a best practices or an ideal configuration for this.
Currently I have:
ASA5510 ---> 2811 ---> ISP_A
Should I purchase another 2811 for ISP_B and connect it to an available port on the ASA? Or should I just purchase a HWIC-1FE and add ISP_B to the existing router?
I see some advantages to both, but not sure the best way to go. Of course, I could be looking at this wrong and if I plan on buying another router then maybe I should use HSRP and both routers should connect to both ISPs.
View 2 Replies
View Related
Dec 12, 2010
Is there an ethernet WIC/HWIC that supports NAT for the 2811. I have one 4 port 10/100 card but it doesn't support NAT overload.
View 5 Replies
View Related
Jun 3, 2013
I have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
View 4 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Apr 14, 2012
I currently have a Cisco 2621 powering a network at our co-location facility... It's a simple setup and is working well. The colo provides a redundant HSRP uplink, so I have their two uplinks going into a Dell switch. From that Dell switch I have a uplink into FastEthernet0/0 on the 2621, configured with my routing network, and then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.
View 11 Replies
View Related
Jul 31, 2012
I have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
View 3 Replies
View Related
Oct 20, 2011
I have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies
View Related
Mar 16, 2010
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Dec 5, 2011
if the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies
View Related
Dec 18, 2012
I was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
View 6 Replies
View Related
Aug 19, 2012
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies
View Related
May 19, 2013
I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies
View Related
Dec 12, 2011
I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
View 3 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Dec 14, 2011
i have question about router 2811, for now, all HWIC in 2811 is full,
Slot 0 : VIC2-2E/M
Slot 1 : VIC2-2E/M
Slot 2 : WIC-1T=
Slot 3 : HWIC-1FE
But we need add more 2 module VIC3-2E/M. can we use Network Module ? example : add one NM-HD-2V + two VIC3-2E/M ?
Can we do that? and whether it is the same as we use the VIC2-2E / M on HWIC slots
View 2 Replies
View Related
Apr 5, 2011
We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies
View Related
Jun 5, 2011
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies
View Related
Sep 3, 2012
I have a win xp system which connects to internal network & Internet. The problem I have is, for each work i need to change the IP address.
Ex: For internal network the ip should be 192.168.0.1 To connect to internet the ip should be 192.168.1.1
Now I want to be connected to both internal network as well as internet at the same time. So what should I do ?
* I can not add another physical network card.
* I can not change the IP's of any other system or config servers etc... (as it is used by our internal application, doing so will make a mess.)
* I have the admin rights so any software changes to my system can be done.
So i was hoping to add a virtual network card, and configure it to the new IP. So can that be done ? if so how ?
View 7 Replies
View Related
