Cisco WAN :: Loading Configuration From Flash Card In 2811 Router?
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
ADVERTISEMENT
Feb 15, 2011
I am trying to upgrade a router 2811, the flash has 64 mb and currently has a IOS 32 mb, but require update it with a IOS 37 mb.
What should I do?, I cannot have the two ios in the flash.
View 3 Replies
View Related
Sep 12, 2012
I need to upgrade the IOS and therefore change the flashcard on a router 2811.
What is the procedure to change the flash (64MB to 256MB) on a 2811 router?
I can remove the flashcard when the router has already started, change the flashcard and load the new IOS?
View 3 Replies
View Related
Aug 23, 2011
I've a problem with a router 2811:
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[Code]......
View 14 Replies
View Related
May 22, 2012
I have a WRT54G with updated firmware. Today I saved my configuration to a config.bin file. When I tried loading the file, the admin screen went blank. Now I am no longer able to access either the internet or the router's admin page. Is a hard reset my only option?
View 6 Replies
View Related
Oct 20, 2011
I have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
Oct 6, 2010
I'm having an issue with a Cisco 2811 ISR Router. Sh ver command output lists the correct ios that the router used for booting and it says that the ios is stored in flash but when i give "sh flash" command it doesn't display the ios file. Maybe the flash is corrupted or damaged in some way? In the attached file is the output from the "sh ver" and "sh flash" commands.
View 6 Replies
View Related
Nov 8, 2011
I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
View 5 Replies
View Related
Jul 7, 2011
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies
View Related
Jun 9, 2007
I downloaded an update for the 1370 wireless card from the microsoft site and now my wireless network doesn't work. I went to the dell site and got the driver directly from the dell site (R140747.EXE) and it fails after it reached 59% complete. I tried another download recommended from this forum (R151519.EXE) and the same error at 59%. I have tried everything I have seen in the forums (closing virus software, editting setup ini file, etc) and I still get Update 778 error at 59%. I am running on an Inspirion 6000, CARD (CIRCUIT), IRELESS, MINI PCI CARD, 1370, BROADCOM CORPORATION, Dlink wireless router, windows xp with sp2, USA. I have also received an error that says something about internal setting incompatible (unfortunately I didn't capture the exact wording - I will attempt to recreate the error) This is terribly frustrating considering I was only following the dell suggestion that I update the driver and now that I attempted it, my laptop is sitting not being used.
View 5 Replies
View Related
Mar 24, 2011
1. Do all the 2800 series have a rocker power switch on the rear?
2. Do all 2800 automatically power on when power is connected if the rocker is in the on position?
3. Is it possible to physically damage the flash card in a 2800 router if it was powered off during a write operation?
The story is I have a client who claims that the flash card was damaged due to a power off.
View 2 Replies
View Related
Mar 15, 2012
I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
View 1 Replies
View Related
Nov 20, 2011
I have several Cisco 2811 ISR Routers that are functioning as CallManager MGCP voice gateways. These routers have prtial PRI's attached to them which I realize are not supported by Cisco CallManager using MGCP. The problem is that whenever the router gets rebooted, the configuration under Controller T1 ends up with the improper PRI Timeslots command and I have to go in and manually change it. Solution: I have developed smal text files for each router that contains all of the commends needed to get the chnage accomplished (you have to shut down things and remove lines elsewhere to be able to change the PRI Timeslots) and I just telnet to the router and cut and paste the commands into the router.However, I would like to store those files on the router in such a way that I could telenet to the router and then either somehow display the file and then copy/paste it in or possible have a file that could be run to make the changes. That way I could do the job quickly fram anyplace I could telnet to the router and not have to have the text files on the local machine.
View 1 Replies
View Related
Jun 10, 2012
Can I use Sandisk Compact 4GB Flash card on Cisco 2800 series Routers
View 8 Replies
View Related
Apr 10, 2011
I have a number of SFE2000 10/100 24 port POE switches. They are configured and running OK. I want to be able to save the configuration and be able to load that saved configuration into another new swich in the case of a failure.
I have logged in and gone to Admin-File Management-Save Configuration. I then select the 'Backup' radio button and TFTP the configuration to my TFTP server. All works OK and I have a readable text file with the switch configuration on my TFTP server.
I want to be able to restore that saved configuration on to a new switch. I have set the new switch back to factory defaults. I go to Admin-File Management-Save Configuration. I then select the 'Upgrade' radio button and try and uploade the file into the switch. If load to 'Running Configuration' the switch shows a status of 'Copy Finished' but says 'Copy completed with errors' If load to 'Startup Configuration' the switch shows a status of 'Copy Failed' and says 'Copy completed with errors'
I am guessing I should be able to load my saved Configuration back into a switch, shouldn't I??
And yes the switches are running the same firmware 3.0.0.17
View 7 Replies
View Related
Aug 25, 2012
With firmware 1.0.4.17 I am have issues with configuration pages not loading and needing to restart the web interface and login again. This is a new problem that started after updating to 1.0.4.17
How many months until we can expect a fix?
View 3 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Dec 9, 2011
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies
View Related
Sep 13, 2011
Is there a way to load a spare compact flash with a running-config, ASA IOS, & ASDM software via card reader? I need to load another flash card with all of the settings necessary for normal operation. This "spare" card will replace the flash that is currently in use. The reason for the replacement is capacity and because of changes made to the running-config. The "in-use" card is 256MB, the "spare" one is 512MB. Also, the new card will have a few changes made to the running-config, so it will, in essence, be a reload.
I have a card reader for the compact flash cards. If there is a way to load up this new card using the card reader, without monkeying with the firewall, I would prefer that. Like I said in the previous paragraph, this new flash card will replace the other one, once it's ready.
Hardware: ASA 5510
CF: 256MB (wanting to upgrade to the new 512MB card)
ASA IOS: 8.4
View 15 Replies
View Related
Nov 20, 2012
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
View 2 Replies
View Related
Jul 11, 2011
We have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
View 3 Replies
View Related
Jul 22, 2007
We have open a division in the UK and are using DSL as a back up to a T1-E1, so I was going to use a standard DSL Modem but thought the WiC-1ADSL-I-DG would be better. However I can seem to get the card up and running. Here is the interface config and sh int atm.
interface ATM0/1/0
ip address dhcp
ip access-group 102 in
ip inspect SDM_LOW out
[code]....
That's part of the sh int amt.
View 9 Replies
View Related
May 18, 2011
I had a question regarding the Cisco 2811. I tried fitting an NM 2FE-2W card and the fast Ethernet interfaces of the module never get recognized. Is there a special command to enable it or isn't the module supported at all by the router. If not , is there a way to have the router possess more than the 2 Fast Ethernet interfaces it already has? Let me know if any more info is needed from my end.
Another question I have out of curiosity. Is it possible to make the controller T1 port of a VWIC 1MFT-T1 or a VWIC 2MFT-T1 act as a fast Ethernet.
View 21 Replies
View Related
Oct 26, 2011
what routed ethernet card (WAN) can be inserted in Cisco 2811? I wan to replace 2Mbps Framerelay to 10 Mbps
View 5 Replies
View Related
Feb 25, 2011
I am facing the problem as my CISCO router is detecting the RS 530 DCE cable as DTE 530idb. I am using this cable for X25 link connectivity. The same cable has worked for more than 1 hour with detecting the cable type as 530 DCE, but suddenly it stops the X25 data transfer. After that the cable type it is showing as DTE 530idb.
Below troubleshooting already carried out.
1. Changed the slot, but same output.
2. Removed the cable & reconnected, but same output.
3. Without connecting to the DTE device also, the cable type is showing as DTE 530idb
View 1 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Mar 26, 2012
I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies
View Related
Oct 13, 2011
I have faced configuration of multiple nat/pat problem.Point is when I paste into router another nat pool or nat with route-map or just static nat they doesn't work I mean only one of them works.So, I have several connection hardware cisco 2811 latest ios 15.1
1. internet
2. Local host that must be translated into global local ip addresses be routed
3. vpn local hosts that must be translated into local global addres
View 4 Replies
View Related
May 2, 2013
I have a 2811 router that I need to confirm NAT configurations as expected. I have 2 deviced on the internal LAN that need to access remote resources without PAT. All the other devices are for a guest network with PAT. My interface Fa0/0 is connected to local network (1.1.1.1/23). Fa0/1 is connected to ISP (10.10.10.178/30). Addressable range from ISP of 10.10.10.192/28 (10.10.10.193-10.10.10.206). Internal machine 1.1.1.2 & 1.1.1.3 must connect to a remote server through internet on spacific port numbers.
View 2 Replies
View Related
Feb 26, 2012
Trying to copy the system image file from the sup-bootflash to a new 64MB ATA flash card. Yes the software can support the 64MB card.
The ATA flash card was formated successfully, however I cannot copy the system image to it so that it can boot after a power loss.
The command I tried was: console(enabled) copy sup-bootflash: slot0:
The source filename was typed in as shown in the Show Verison command.The result was: Error opening slot0: no such device.I suspect that I am missing something obvious as I am new to Cisco Switches.
View 1 Replies
View Related
Nov 1, 2011
does cisco 2811 support?if no, can i make it work for BGP?also, i want to know the configuration of bGP for twoo ISPs for link failover.it will be google if u tell me step by step approach for configuring it
View 1 Replies
View Related
