Cisco :: Configuring A 2811 With FXS Card To Register With CM?
Jul 11, 2011
We have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
View 3 Replies
ADVERTISEMENT
Sep 13, 2012
Facing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
View 4 Replies
View Related
May 31, 2010
I have Cisco 2811 Router and few days ago my router doesn't work correctly. I checked config and found config-register was changed (0xC502).
HUV_Murun#sh version
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
HUV_Murun uptime is 23 hours, 36 minutes
[code]...
Configuration register is 0xC502. What is the meaning of this config-register (0xC502) and how can be changed config ?
View 3 Replies
View Related
Nov 2, 2011
I have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies
View Related
May 26, 2012
I have a 2811 ISR configured to provide the following services to my network: Internet access to LAN usersCisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations.Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 2 Replies
View Related
May 26, 2012
I have a 2811 ISR configured to provide the following services to my network:
Internet access to LAN users Cisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 3 Replies
View Related
Jun 13, 2011
I have configured Cisco 2811 and 3825 routers to connect the main and remote sites as per the attached topology. At the main site, the Cisco 3825 router is equipped with SFP ports (HWIC-1GE-SFP with GLC-LH-SM=) for fiber optic connectivity and also has a HWIC-1CE1T1-PRI installed The Cisco 2811 routers at the remote sites are each equipped with a WIC-1SHDSL-V3 module for SHDSL connectivity and with a WIC-1B-S/T-V3 for backup ISDN connectitivty.
In normal time the routers are using the SHDSL to Fiber optic connectitivty for communication. This has already been configured and is working. Now, there is a need to implement a backup connection between these sites such that in case the SHDSL or fiber optic connectivity fails, the routers should automatically dial up the backup ISDN connectivity so as to ensure business continuity.
View 3 Replies
View Related
Oct 20, 2011
I have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies
View Related
Jul 22, 2007
We have open a division in the UK and are using DSL as a back up to a T1-E1, so I was going to use a standard DSL Modem but thought the WiC-1ADSL-I-DG would be better. However I can seem to get the card up and running. Here is the interface config and sh int atm.
interface ATM0/1/0
ip address dhcp
ip access-group 102 in
ip inspect SDM_LOW out
[code]....
That's part of the sh int amt.
View 9 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
May 18, 2011
I had a question regarding the Cisco 2811. I tried fitting an NM 2FE-2W card and the fast Ethernet interfaces of the module never get recognized. Is there a special command to enable it or isn't the module supported at all by the router. If not , is there a way to have the router possess more than the 2 Fast Ethernet interfaces it already has? Let me know if any more info is needed from my end.
Another question I have out of curiosity. Is it possible to make the controller T1 port of a VWIC 1MFT-T1 or a VWIC 2MFT-T1 act as a fast Ethernet.
View 21 Replies
View Related
Oct 26, 2011
what routed ethernet card (WAN) can be inserted in Cisco 2811? I wan to replace 2Mbps Framerelay to 10 Mbps
View 5 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
Feb 25, 2011
I am facing the problem as my CISCO router is detecting the RS 530 DCE cable as DTE 530idb. I am using this cable for X25 link connectivity. The same cable has worked for more than 1 hour with detecting the cable type as 530 DCE, but suddenly it stops the X25 data transfer. After that the cable type it is showing as DTE 530idb.
Below troubleshooting already carried out.
1. Changed the slot, but same output.
2. Removed the cable & reconnected, but same output.
3. Without connecting to the DTE device also, the cable type is showing as DTE 530idb
View 1 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Nov 13, 2012
I am using a Cisco 1921 with a Verizon 4G LTE card installed. The primary connection is a Cable Modem with the 4G LTE acting as the backup. I've setup a track on the static route to the primary ISP. I'm having multiple issues. Initially I used the Gig 0/0 int instead of a Loopback address for the IP SLA source. The IP SLA traffic would be sent to the cellular interface and cause an IP source violation and the interface would flap. Then I used the Loopback and I could not get the route to fail back when the connection came back up. Even with the Loopback as the source for IP SLA I'm still getting flapping and I think that is a NAT configuration issue. I've applied an access-group on the cellular interface to try to fix the ip source violation issues, but it doesn't appear to work. The IP-SLA-POLICY route map is an attempt to force the IP SLA traffic to the primary interface. [code]
View 1 Replies
View Related
Mar 26, 2012
I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies
View Related
Jul 5, 2011
brought 2nd hsnd pda and then a wireless card to access internet. Have tried everything but can't get connection to work. Card flashes, pda flashes but no connection.
View 1 Replies
View Related
Jul 24, 2012
Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies
View Related
Dec 12, 2011
I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
View 3 Replies
View Related
Mar 7, 2011
I need to run a windows hyper terminal program between my POS register which has a serial RJ11 port to my PC db9 male port
View 2 Replies
View Related
Feb 6, 2007
I have tried the config-register command and it is not available. Here is part of the show ver command. I want to change the config-reg from 0xF to 0x2102.I have run into this before but don't remember how to correct it.....I think I have to use the boot command but not sure. Here it the output show ver Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on?System image file is "flash:c2960-lanbase-mz.122-25.FX/c2960-lanbase-mz.122-25.FX.bin"cisco WS-C2960-24TT-L (PowerPC405) processor (revision A0) with 61440K/4088K bytes of memory.last reset from power-on
4 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.64K bytes of flash-simulated non-volatile configuration memory.
Model number : WS-C2960-24TT-L
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)FX C2960-LANBASE-M
Configuration register is 0xF
View 6 Replies
View Related
Mar 30, 2011
I'm having troubles with a cisco 877 router, it keeps changing itself to either 0x2101 which is good, or to 0x3100 which is bad because it messes up my bautrate to 1200 instead of 9600.it doesn't seem to matter if I change it, it will still tell me that it will change at next reload. [code]
I have never seen this before.the command in conf t : configuration-register 0x2101 is not working, played with wr mem or copy start run neither of one useful.
View 5 Replies
View Related
Feb 21, 2011
Whenever I go to sites like godaddy.com or mydomain.com to register a personal domain, they only offer me sites like url...What can I do? Computers have lots of memory but no imagination..
View 1 Replies
View Related
Mar 30, 2012
I am trying to implement a small VoIP LAN (you can see the lan in attachments)for a personal project. I am using:
- 2 x XP (on which i installed Cisco IP Communicator 7.0.3.0)
- 1 x Ubuntu (running GNS3 with a c3600 Router)
The problem is that the phone which is not in the same LAN with the tftp server cannot register.
1) Can a phone register to a tftp server from another LAN ?
2) If the answer for 1) is yes, what am i doing wrong (you can see the details in the attachments)? I mention that the ping works well anywhere in the LAN.
View 11 Replies
View Related
Jun 1, 2013
I am having two 6509E working in VSS and both are working fine. But the configuration register of command "remote command switch show boot" is 0x8000 which is different from that of RP (0x2102) .Now i want to change the value of configuration regsiter of SP to 0x2102.
View 1 Replies
View Related
May 17, 2012
I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
View 4 Replies
View Related
May 15, 2012
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
View 1 Replies
View Related
Jan 12, 2011
I have just upgraded one of our 4400 to 7.0.98.0. Most of the AP re-registered with out issues. I have two AIR-LAP1142N-E-K9 on a remote site that will not re-register.I have pointed them to another 2125 WLC (7.0.98.0) and they register fine. Point them to yet another 4400 (7.0.98.0) I get the same issue.I am getting this error when the register on the 4400s.*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'abzewwlc'(index 1).*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller *Jan 11 07:05:55.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 144.46.211.5 peer_port: 5246*Jan 11 07:06:55.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 144.46.211.5:5246 I suspect it may be as they both have In the client config.Then again maybe not.Configured Switch 1 Addr 158.139.177.203Configured Switch 2 Addr 144.46.214.25
Question 1 if I do a "clear config except static IP" will I still be able to telnet tp them or will they default to no telnet no ssh ?
Question 2 any idea how to get past this DTLS error ?
View 4 Replies
View Related
May 8, 2013
I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 Replies
View Related
Jul 6, 2011
I am implementing Cisco Network Access Control with Wireless Controller 5508 (WLC5508 below) . Could you tell me how to register WLC5508 as SNMP Agent for Cisco Access Manager (CAM below) ?
[System Information]
IOS version of WLC5508: 7.0.98.218
Version of CAM: 4.8.0
[Code]....
I succeeded to register WLC5508 by using IP address of Service Port on the CAM Web Console. But WLC5508 has only one Service Port, which has no redundant port. I want to register it by usin Management Interface, which has backup port. It is also desirable to implement redundancy of Service Port if possible.
View 2 Replies
View Related
Dec 26, 2012
I am using PC to mobile dialer. It was working fine but now I am unable to login to my wowcall account due to error - Unable to register to SIP server.
View 1 Replies
View Related
