Connection Between POS Register And PC?
Mar 7, 2011I need to run a windows hyper terminal program between my POS register which has a serial RJ11 port to my PC db9 male port
View 2 Replies
ADVERTISEMENT
Servers :: How To Register Website
Feb 21, 2011Whenever I go to sites like godaddy.com or mydomain.com to register a personal domain, they only offer me sites like url...What can I do? Computers have lots of memory but no imagination..
View 1 Replies View RelatedError - Unable To Register To SIP Server
Dec 26, 2012I am using PC to mobile dialer. It was working fine but now I am unable to login to my wowcall account due to error - Unable to register to SIP server.
View 1 Replies View RelatedCisco WAN :: How To Set Config-register On 2960
Feb 6, 2007I have tried the config-register command and it is not available. Here is part of the show ver command. I want to change the config-reg from 0xF to 0x2102.I have run into this before but don't remember how to correct it.....I think I have to use the boot command but not sure. Here it the output show ver Cisco IOS Software, C2960 Software (C2960-LANBASE-M), Version 12.2(25)FX, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C2960 boot loader
BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
System returned to ROM by power-on?System image file is "flash:c2960-lanbase-mz.122-25.FX/c2960-lanbase-mz.122-25.FX.bin"cisco WS-C2960-24TT-L (PowerPC405) processor (revision A0) with 61440K/4088K bytes of memory.last reset from power-on
4 Virtual Ethernet interfaces
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.64K bytes of flash-simulated non-volatile configuration memory.
Model number : WS-C2960-24TT-L
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 12.2(25)FX C2960-LANBASE-M
Configuration register is 0xF
Cisco WAN :: 877 Keeps Changing Configuration Register
Mar 30, 2011I'm having troubles with a cisco 877 router, it keeps changing itself to either 0x2101 which is good, or to 0x3100 which is bad because it messes up my bautrate to 1200 instead of 9600.it doesn't seem to matter if I change it, it will still tell me that it will change at next reload. [code]
I have never seen this before.the command in conf t : configuration-register 0x2101 is not working, played with wr mem or copy start run neither of one useful.
Cisco :: Configuring A 2811 With FXS Card To Register With CM?
Jul 11, 2011We have a few remote sites that connect back to HQ with T1 & DMVPN (Cable/DSL) for data. Our CM Publisher/Subscriber reside in HQ. We recently installed FXS cards in these routers to provide Fax functionality to our remote sites since we will be removing some POTS lines.
Can we register the 2811 as a voice gateway (I am thinking MGCP as with VG224's we have in production) and have it handle faxes with FXS card as well as route data or will we need a separate device for this?
Cisco :: Can A Phone Register To Tftp Server From Another LAN
Mar 30, 2012I am trying to implement a small VoIP LAN (you can see the lan in attachments)for a personal project. I am using:
- 2 x XP (on which i installed Cisco IP Communicator 7.0.3.0)
- 1 x Ubuntu (running GNS3 with a c3600 Router)
The problem is that the phone which is not in the same LAN with the tftp server cannot register.
1) Can a phone register to a tftp server from another LAN ?
2) If the answer for 1) is yes, what am i doing wrong (you can see the details in the attachments)? I mention that the ping works well anywhere in the LAN.
Cabling / Cards :: Computer Doesn't Register Anything At All
Feb 6, 2012I've just moved my desktop computer back to my parents house. there is an Internet connection in the house already. if I plug the cable into my laptop it works instantly. when I plug into the desktop there is nothing the green light turns on at the back of the tower but otherwise the computer doesn't register anything at all.
View 7 Replies View RelatedLinksys Wireless Router :: Cannot Register E2500
Sep 3, 2012i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies View RelatedLinksys Cable / DSL :: Why Cannot Register WAG160N Router
Dec 22, 2008Why can I not register a WAG160N router with Linksys? Is this because these devices are not sold in the US?
View 4 Replies View RelatedLinksys Wireless Router :: Can't Register The WRT160N V2
Jul 15, 2011Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies View RelatedCisco :: 6509E Changing Configuration Register Of SP
Jun 1, 2013I am having two 6509E working in VSS and both are working fine. But the configuration register of command "remote command switch show boot" is 0x8000 which is different from that of RP (0x2102) .Now i want to change the value of configuration regsiter of SP to 0x2102.
View 1 Replies View RelatedCisco Wireless :: 4402 Could Not Register IP Add On MSCB
May 17, 2012I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
Cisco Wireless :: 22xx - How LWAP Register To WLC
May 15, 2012i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
Cisco :: 4400 DTLS Error AP Will Not Register
Jan 12, 2011I have just upgraded one of our 4400 to 7.0.98.0. Most of the AP re-registered with out issues. I have two AIR-LAP1142N-E-K9 on a remote site that will not re-register.I have pointed them to another 2125 WLC (7.0.98.0) and they register fine. Point them to yet another 4400 (7.0.98.0) I get the same issue.I am getting this error when the register on the 4400s.*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'abzewwlc'(index 1).*Jan 11 14:39:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller *Jan 11 07:05:55.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 144.46.211.5 peer_port: 5246*Jan 11 07:06:55.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 144.46.211.5:5246 I suspect it may be as they both have In the client config.Then again maybe not.Configured Switch 1 Addr 158.139.177.203Configured Switch 2 Addr 144.46.214.25
Question 1 if I do a "clear config except static IP" will I still be able to telnet tp them or will they default to no telnet no ssh ?
Question 2 any idea how to get past this DTLS error ?
Cisco Wireless :: 36021 AP Failed To Register WLC
May 8, 2013I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 Replies View RelatedSWR54BGA / Router Won't Register With The Pppoe Server
Dec 24, 2010There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies View RelatedCisco WAN :: 2811 / Configure Register Value Changes Automatically?
Sep 13, 2012Facing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
Cisco :: How To Register WLC5508 As SNMP Agent For CAM
Jul 6, 2011I am implementing Cisco Network Access Control with Wireless Controller 5508 (WLC5508 below) . Could you tell me how to register WLC5508 as SNMP Agent for Cisco Access Manager (CAM below) ?
[System Information]
IOS version of WLC5508: 7.0.98.218
Version of CAM: 4.8.0
[Code]....
I succeeded to register WLC5508 by using IP address of Service Port on the CAM Web Console. But WLC5508 has only one Service Port, which has no redundant port. I want to register it by usin Management Interface, which has backup port. It is also desirable to implement redundancy of Service Port if possible.
Cisco Switches :: SG200 Trying To Register Warranty Online
Jun 13, 2012I have just purchased SLM2016T-UK (SG200-18) and trying to register the warranty online (was told by the reseller to do so) but I can't find any link direct me to the correct site.
View 4 Replies View RelatedCisco AAA/Identity/Nac :: Unable To Register A Secondary ACS 5.2 Appliance
Dec 6, 2011 I have installed 2 ACS 5.2 appliances, the two appear as Primary. When I try to register one of them with the other one using "System Administrator -> Local Operation -> Deployment Operations" I get the following message:
This System Failure occurred: Unable to authenticate with node.. Your changes have not been saved.Click OK to return to the list page.
I have tried with both "ACSAdmin" and "admin" users with their respective passwords.
Cisco Wireless :: CAP1602I-E-K9 Can't Register With 2500 Controller
May 18, 2013I am developing CAP1602I & 2500 Controller.The CAP1602I-E-K9 can't register with the 2500 controller. [code] logging appears: capwap can't process uncryped data..I even didn't configure capwap on CAP1602.May I know if CAP1602 doesn't support LWAPP? Why LWAPP doesn't work?According to the logging, I also tried to configure the "Data Encryption" on 2500 controller ( according to 7.0.116.0 guide)
"Cisco 2500, WiSM2, WLC2—By default, these platforms do not contain DTLS. To turn on data DTLS, you must install a license. These platforms have a single image with data DTLS turned off. To use data DTLS you will need to have a license."Note If your controller does not have a data DTLS license and if the access point associated with the controller has DTLS enabled, the data path will be unencrypted. I should purchase a license? or, if I can configure the CAP1602I to don't encrypt data?
Cisco Wireless :: Not Able To Register AP Point On 4402 WLC Running IOS
Jul 15, 2012Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies View RelatedCisco Wireless :: 1231 Fail To Register To Primary WLC
Oct 29, 2011We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies View RelatedCisco Wireless :: 2504 WLC Reboots When AP Attempts To Register
Jan 14, 2013I have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
Cisco AAA/Identity/Nac :: ACS 5.3 - Unable To Re-register Secondary To Primary?
Jun 11, 2012Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
Cisco Switching/Routing :: Config Register On 4507R
Jun 5, 2012Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies View RelatedCisco Wireless :: 2602AP's Won't Register With 5508 Controller
Dec 12, 2012We have a 5508 controller that manages AP's at approximately 20 branches - each branch has their own subnet. We have a single branch (subnet) with new 2602 AP's that will not register with the controller. All communications to this subnet appear normal and there are no ACL's in place between the AP's and the controller. The AP's are able to resolve the controller IP address via DNS and begin the registration process but then timeout. We have successfully installed 2602 AP's at other branch locations and they register with no problems - this is only a problem at a single branch. I've attached some debug messages below for a single AP (this is a production environment so I parsed un-necessary info) and also included the console messages from a different AP (the console messages on the AP's are the same). There are currently 9 AP's at this location and none of them will register.
Debug Capwap Events:
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Discovery Request from 10.29.9.190:44306
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 300, joined Aps =272
[Code]......
Cisco Wireless :: 1262 AP Doesn't Register With WLC4404
Oct 15, 2012We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
Cisco :: Cause High Latency After AP Register WLC 2500 Over Different Network
May 27, 2013\We have purchased AP 1041 and WLC 2500 and I am doing a testing on the configuration. It is fine when both AP and WLC are sitting on the same network. However, if I connect the AP to the WLC which is on another network, I found that latency is quite high when PING the gateway. Here is the brief topology.
AP (172.30.40.212) ------- (VLAN 1: 172.30.40.202) switch (VLAN 2: 172.30.41.202) ----------- (172.30.41.210) WLC
I try to plug the PC to VLAN 1 and do a PING test to the VLAN 1 interface and it causes some packet loss and high latency. [URL] If I do the debug ip udp on the AP, it seems the result is normal.
*May 28 13:53:36.951: UDP: sent src=172.30.40.212(26610), dst=172.30.41.210(5246), length=1069
*May 28 13:53:36.952: UDP: rcvd src=172.30.41.210(5246), dst=172.30.40.212(26610), length=89
*May 28 13:53:36.953: UDP: sent src=172.30.40.212(26610), dst=172.30.41.210(5246), length=685
*May 28 13:53:36.954: UDP: rcvd src=172.30.41.210(5246), dst=172.30.40.212(26610), length=89
Configuration:
AP 1041 Version: 15.2(2)JB
WLC 2500 version: 7.4.100.0
Both device are configured the static IP address manually with default setting and I do not enable DHCP option 43.
Cisco Wireless :: Can't Register AP 1231 On 2504 WLC Controller
Apr 28, 2013WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
Cisco WAN :: ASA 5510 - Ping Gets Through But Phone Unable To Register?
Jan 31, 2011I have to sites connected togather using 4 MBps Link over the tunnel terminated on asa 5510,the call manager in site 1 and the other users on the site 2 unable to register with call mamager on site while i have a suceesull ping goes from site 2 to site 1 (call manager ip) so why this phone its not registered ,so in term of network no problems coz the ping gets through and am rely on ping to confirm that no network problem
----is there any udp traffic problem that prevent the phone registration
Identify Physical Address To Register In New Network To Continue Using Modem?
Sep 15, 2011I bought the modem from clearwire but after a period of time cancel internet because price is going up, i get to retain the modem, I live at campus now and i can get free internet by registin my physical adress and model. How can I identify the physical adress to register it in a new network to continue using the modem and pick up the signal with my modem..
View 1 Replies View Related
