Cisco Wireless :: CAP1602I-E-K9 Can't Register With 2500 Controller
May 18, 2013
I am developing CAP1602I & 2500 Controller.The CAP1602I-E-K9 can't register with the 2500 controller. [code] logging appears: capwap can't process uncryped data..I even didn't configure capwap on CAP1602.May I know if CAP1602 doesn't support LWAPP? Why LWAPP doesn't work?According to the logging, I also tried to configure the "Data Encryption" on 2500 controller ( according to 7.0.116.0 guide)
"Cisco 2500, WiSM2, WLC2—By default, these platforms do not contain DTLS. To turn on data DTLS, you must install a license. These platforms have a single image with data DTLS turned off. To use data DTLS you will need to have a license."Note If your controller does not have a data DTLS license and if the access point associated with the controller has DTLS enabled, the data path will be unencrypted. I should purchase a license? or, if I can configure the CAP1602I to don't encrypt data?
View 10 Replies
ADVERTISEMENT
Mar 5, 2013
I have therefore 2504 Wireless Controller with a wireless access point AIR-CAP1602I-E-K9 (LWAPP image version 7.4.1.37) I saw that I needed to update the Controller in 7.4 for compatibility with my AP. Now when I connect my AP I get error messages:
*Mar 1 00:01:02.387: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:02.387: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
[Code]....
View 10 Replies
View Related
May 27, 2013
\We have purchased AP 1041 and WLC 2500 and I am doing a testing on the configuration. It is fine when both AP and WLC are sitting on the same network. However, if I connect the AP to the WLC which is on another network, I found that latency is quite high when PING the gateway. Here is the brief topology.
AP (172.30.40.212) ------- (VLAN 1: 172.30.40.202) switch (VLAN 2: 172.30.41.202) ----------- (172.30.41.210) WLC
I try to plug the PC to VLAN 1 and do a PING test to the VLAN 1 interface and it causes some packet loss and high latency. [URL] If I do the debug ip udp on the AP, it seems the result is normal.
*May 28 13:53:36.951: UDP: sent src=172.30.40.212(26610), dst=172.30.41.210(5246), length=1069
*May 28 13:53:36.952: UDP: rcvd src=172.30.41.210(5246), dst=172.30.40.212(26610), length=89
*May 28 13:53:36.953: UDP: sent src=172.30.40.212(26610), dst=172.30.41.210(5246), length=685
*May 28 13:53:36.954: UDP: rcvd src=172.30.41.210(5246), dst=172.30.40.212(26610), length=89
Configuration:
AP 1041 Version: 15.2(2)JB
WLC 2500 version: 7.4.100.0
Both device are configured the static IP address manually with default setting and I do not enable DHCP option 43.
View 1 Replies
View Related
Dec 12, 2012
We have a 5508 controller that manages AP's at approximately 20 branches - each branch has their own subnet. We have a single branch (subnet) with new 2602 AP's that will not register with the controller. All communications to this subnet appear normal and there are no ACL's in place between the AP's and the controller. The AP's are able to resolve the controller IP address via DNS and begin the registration process but then timeout. We have successfully installed 2602 AP's at other branch locations and they register with no problems - this is only a problem at a single branch. I've attached some debug messages below for a single AP (this is a production environment so I parsed un-necessary info) and also included the console messages from a different AP (the console messages on the AP's are the same). There are currently 9 AP's at this location and none of them will register.
Debug Capwap Events:
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Discovery Request from 10.29.9.190:44306
*spamApTask0: Dec 11 14:39:32.904: 44:2b:03:9a:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 300, joined Aps =272
[Code]......
View 28 Replies
View Related
Apr 28, 2013
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
View 4 Replies
View Related
Nov 20, 2012
I am trying to configure the Wism running on a 6500 switch.... I have configured the DHCP scope for the AP on the controller itself with the same subnet as of the management for the controller. The AP gets the IP but once it restarts it doesn't register to the controller, this is the log i get on the AP when consoled into it. [code]
View 6 Replies
View Related
Nov 20, 2011
I am having trouble adding a new controller(2500) to the WCS.
-My WCS version 6.0.196.0
-My WLC version 7.0.116.0
If i upgrade my WCS i may add the new contoller? Even if in cisco DATA-SHEET there isnt any mention regarding this WLC(basicly it says that the WCS does not support this WLC)
Monitoring and migration of selected Cisco Aironet standalone (autonomous) access points. Monitoring of the standalone access points of Cisco 800, 1800, 2800, and 3800 Series Integrated Services Routers.
View 3 Replies
View Related
May 10, 2013
By any way can I achieve HA in 2500 controller? I dont mind even I didnt get Stateful switchover.
View 5 Replies
View Related
Dec 7, 2012
i am having wirless controller cisco 2500 series. i want to know how many web authentication users i can create in the 2500 series controller with time out option for each users.
i know it will support the web authentication for internet access for the users but i need to know how many it will accept at a time with hours specification.
View 4 Replies
View Related
Nov 27, 2011
know if Cisco LMS will ever support the 2500 wireless controller ? I have just checked the supported devices for LMS 4.1 and the controller is not there.
View 1 Replies
View Related
May 16, 2012
I have a Cisco 2500 Wireless Controller connected and controlling 5 Cisco AP's. Everything works fine except one device.
This device is used to connect to our AP wirelessly and then any of the wireless laptops can use programming software to connect to the device and program through it. I can successfully set up our device on the network and all PCs can ping it, but the programming software refuses to connect to it. I spent an hour and a half on the phone with the device people who assure me its the network. So, I bought in a cheap Linksys router, hooked one laptop up to it and configured the device wirelessly. With that, the programming software works.
what should I be looking for in the Wireless Controller that may be blocking direct connection to the device even though I can ping it?
View 10 Replies
View Related
Feb 14, 2013
We are currently using a Cisco 2500 (licensed for 50 AP's) WLAN Controller. There has been a lot of issues setting up the VOCERA wireless badges, thats on going. The question I have is all the AP's are showing as being on Channel 6, it was thought that the controller would learn the enviroment and move these to none overlapping channels, but has not. Is this right should they all be on the same channel and not 1, 6, 11 accordingly? it is also worth mentioning that the controller can see 61 rogue AP's, yes that is 61 other wireless networks!
View 2 Replies
View Related
Jul 27, 2011
give me the run down on the features removed from the 4400 series in the 2500 series? Obviously 4400 is now EOL, and so i cannot purchase new. Therefore I was looking at the 2500 for my implementation to save costs also.I would like to have two SSID's, running seperate VLAN's, one voice, one guest, trunk the link to the AP's, which will be 1131AG or newer, N possibly. Voice needs to be encrypted with WPA or WPA2, guest needs to be open using the guest access feature. Here's a sample but with EAP:
[URL]
Is this supported to have WPA on one SSID and Guest access on the other? i did spot a paragraph in the 4400 manual stating that certain restrictions apply regarding one SSID having encryption and the other being guest mode?I notice also in the WCS documentation, it doesn't explicitly state it supports the 2500 series under the managed devices section?
View 1 Replies
View Related
Dec 3, 2012
We have recently installed Cisco for our wireless solution. We are an education and are looking to let staff and pupils bring their own devices. The route that we are planning to take to let them join the school's WiFi is to implement a RADIUS server so that they can authenticate with their Active Directory username and password. I have tried to test the solution but so far without any success. I am using a Windows Server 2008 R2 as my NPS server, I have setup the Cisco controller as per below:
Security Tab | RADIUS | Authentication - I added my windows server there and the preshared key, the Network User and Management is ticket and the server responds to a ping command,In the WLANs Tab, I selected my test WLAN and under Security | AAA Servers I selected the RADIUS server that I configured in the Security TabI then try to logon to my test WLAN and on the Cisco WLAN controller I get the following error: AAA Authentication Failure for UserName:test User Type: WLAN USER
Before trying to tinker with policies on the Windows Server I was wondering if the RADIUS is correctly setup on the Controller or have I missed something obvious?
View 6 Replies
View Related
Dec 5, 2012
Can I connect various Aironet 1242 to Wireless controller 2500?
View 4 Replies
View Related
Jul 9, 2012
We have a Cisco 2500 WLC with 136 APs. Recently, we discovered eight APs that were not listed on the Wireless > Access Points > All AP list. These APs were once working and connected, but now they are no longer in the All AP list. I located one of these APs and found the green LED blinking. I power cycled the AP and it came back online with a solid green LED and was then registered on the All AP list. The All AP list will only show the connected APs. I would like to know if there is a method to show the APs that were once connected and are no longer registered so we can better identify when an AP is not working?
View 15 Replies
View Related
Apr 17, 2012
I have a customer whom has six LAP1131AG-K9 but no controller and they are interested in one of the new 2500 series, specifically a AIR-CT2504-5-K9 with a 5 AP add-on license to bring total AP capacity to 10. I can't determine clearly if this controller will work for these older AP's prior to them making the jump to 802.11n via the 3500 or 3600 series, looking to the community to confirm.
View 3 Replies
View Related
Apr 21, 2013
Looking for some training on the 2500 series controller and 1142 or 1040 AP's preferably.
View 10 Replies
View Related
Oct 25, 2012
when I did connect the AP to the switch and this is already connected to the WLAN 2500, I got this error message [code] And this AP is not joined to the WLAN 2500, but if I use one model of AP like LAP1120 it works, that mean, the wireless is able to see the Ip Address.How can I do to correct the problem with the AP 3600 series?
View 5 Replies
View Related
Apr 16, 2012
I setup cisco wireless controller 2500 connecting 2 Aironet APs, with windows 2008 NPS as radius server (server certificate installed), via
[WPA2][Auth(802.1X)], MAC Filtering
Now I have domain computer (laptop) connected to SSID which provides direct to the LAN dhcp server. That means my notebook got same ip range as when it connected to LAN.
The user used cached domain logon info to logon the computer, then the wireless profile started to connect with radius server which has User group policy.
Problem is the notebook (logon as normal domain user) browse \"domain name" or any \hostname will take 10 mins or more to pop up with "enter network password" or sometimes "The specified netwrok name is no longer avail". However ever if I simply \192.168.2.x which is the host's ip address, I got list of share folders instantly.
And when I disable the wireless and connect to the LAN cable, I had no problem to browse any shared folders.
View 10 Replies
View Related
May 13, 2012
I have a couple 3600s that don't want to join. One i and one e that are both doing the something. It is able to find the controller via layer 3 discovery but it is acting like it is a mesh AP when it tries to join the controller.
From the 2500 controller (running 7.2)
*spamApTask2: May 13 12:03:05.272: f0:f7:55:ae:xx:xx Mesh AP username f0f755aexx xx.
*spamApTask2: May 13 12:03:10.739: f0:f7:55:ae:xx:xx spamProcessJoinRequest : RA
P, Check MAC filter
From the 3602i
flash:/mesh_start_cfg.txt: No such file or directory. The filesystem containing the variables may not be initialized yet.
I should note that 3500 APs are able to join this controller. The field guy is going to try to add the MAC address to the filter list when he gets back out on site to see if it allows it to join.
View 3 Replies
View Related
Feb 3, 2011
have a Dell Poweredge 2500, and it only has PCI slots, and i need to get a sata controller to add 1/2 drives to it, i am unsure what would be the best, but i am not looking to spend more than 60 or so for it, i am not worried about it being the greatest out there, as this server is going to be replaced in 6 mths, i am just outgrowing the 4-18.6 gig hot swap scsi drives, and my pockets arent deep enough to buy high capacity scsi drives, i will probably add 1, 1 or 2 Terabyte hard drive and a dvd-rw.
View 4 Replies
View Related
Jan 1, 2013
Current, i have a project to deploy wifi for hotel 5 stars.And i have two type AP Cisco AIR-CAP1602I-E-K9 and AIR-AP1261N-E-K9 I want to compare performance about:
+ Coverage Radio ( Power transmitter, antenna gain)
+ Bandwith or throught put
+ Concurrent users or connection
View 20 Replies
View Related
May 22, 2013
I have Cisco Access point AIR-CAP1602I-N-K9 ,My doubt is,is this AP support on WLC AIR-WLC2112-K9
View 1 Replies
View Related
May 17, 2012
I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
View 4 Replies
View Related
May 15, 2012
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
View 1 Replies
View Related
May 8, 2013
I have cisco WLC 5508 on the HQ, now I have another site in different subnet I tried to put AP on it and configure a DHCP pool with option 43 but the AP failed to register the WLC on the HQ.
View 13 Replies
View Related
Jul 15, 2012
Not able to register AP Point < Air-Cap35021-E-K9 > on 4402 WLC running IOS (AIR-WLC4400-K9-7-0-235-0 ) Other AP already registered on the WLC are AIR-LAP1242AG-E-K9 & AIR-LAP1131AG-E-K9.
View 13 Replies
View Related
Oct 29, 2011
We have found that only Cisco 1231 WAP are exhibiting this behaviour. Their Primary WLAN controller is Cisco1 WLC but they fail to register to Primary WLC and fall back to Cisco2 WLC. After about 200 sec , they attempt to connect to Primary WLC once again and fail. The whole cycle is repeated every 250 seconds.
View 3 Replies
View Related
Jan 14, 2013
I have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.
WLC2504 : 7.2.103.0
AIR-LAP1142N-E-K9: Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
View 3 Replies
View Related
Oct 15, 2012
We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
View 4 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Jul 15, 2011
Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
View 1 Replies
View Related
